Hi , Thanks for the reply . Rather than configuration change , I have done through dynamic routing .
In the dr_gateway table I have added socket information *udp:x.x.x.x:5060* mysql> select * from dr_gateways; +----+------+------+---------------------------------------+-------+------------+-------+------------+-------+-----------------------+-------------+ | id | gwid | type | address | strip | pri_prefix | attrs | probe_mode | state | socket | description | +----+------+------+---------------------------------------+-------+------------+-------+------------+-------+-----------------------+-------------+ | 1 | gw4 | 3 | fs.3c.com:6080 | 0 | NULL | NULL | 0 | 0 | udp:192.168.0.69:5060 | NULL | +----+------+------+---------------------------------------+-------+------------+-------+------------+-------+-----------------------+-------------+ I only have a single Invite on a single session on this leg . There is no Re-Invite at all . Will I need to set record_route_preset on this case as well ? *Thanks & Regards* *Sasmita Panda* *Senior Network Testing and Software Engineer* *3CLogic , ph:07827611765* On Wed, Jul 24, 2024 at 7:06 PM Ben Newlin <ben.new...@genesys.com> wrote: > Sasmita, > > > > You need to be using $socket_out. [1] > > > > By default, OpenSIPS will use the receiving socket as the sending socket. > This means if you receive the message on TLS and do not change $socket_out > then the message will be sent out the TLS socket. > > > > Additionally, unless you are using B2BUA or maybe topology_hiding you will > likely need to “remember” this protocol transition by adding a double > Record-Route [2] to the message. You may also need to change any > “transport” params that exist in the Request-URI and possibly the Contact > header. > > > > [1] https://www.opensips.org/Documentation/Script-CoreVar-3-2#toc86 > > [2] https://opensips.org/docs/modules/3.2.x/rr.html > > > > Ben Newlin > > > > *From: *Users <users-boun...@lists.opensips.org> on behalf of Sasmita > Panda <spa...@3clogic.com> > *Date: *Wednesday, July 24, 2024 at 1:54 AM > *To: *OpenSIPS users mailling list <users@lists.opensips.org> > *Subject: *[OpenSIPS-Users] I need some info while setiing sethostport on > opensips config . > > * EXTERNAL EMAIL - Please use caution with links and attachments * > > > ------------------------------ > > Hi All , > > > > I am using openisp version : 3.2 > > > > I have an opensips config on which I was listening on UDP port only and > hence using sethostport to route calls to a particular destination . like > below . > > > > if(is_from_gw() || ($rp=~"5505")) > { > sethostport("freeswitch-test.xyz.com:6080"); > route(inbound); > exit; > } > > > > Now I have to accept a call on TLS and send that to some other destination > on UDP . I have enabled the tls module and also the dependent modules like > tls_openssl, tls_mgm . > > > > socket=udp:192.168.0.y:5060 > socket=tls:192.168.0.y:5061 > socket=tcp:192.168.0.y:5060 > > if(is_from_gw() || ($rp=~"5505")) > { > sethostport("freeswitch-test.xyz.com:6080"); > route(inbound); > exit; > } > > > > This above configuration is not working . I am getting "477 Send Failed " > > > > *Thanks & Regards* > > *Sasmita Panda* > > *Senior Network Testing and Software Engineer* > > *3CLogic , ph:07827611765* > _______________________________________________ > Users mailing list > Users@lists.opensips.org > http://lists.opensips.org/cgi-bin/mailman/listinfo/users >
_______________________________________________ Users mailing list Users@lists.opensips.org http://lists.opensips.org/cgi-bin/mailman/listinfo/users
