Any suggestions on this ?
*Thanks & Regards* *Sasmita Panda* *Senior Network Testing and Software Engineer* *3CLogic , ph:07827611765* On Fri, Jul 26, 2024 at 4:55 PM Sasmita Panda <spa...@3clogic.com> wrote: > Hi , Thanks for the reply . > Rather than configuration change , I have done through dynamic routing . > > In the dr_gateway table I have added socket information > *udp:x.x.x.x:5060* > mysql> select * from dr_gateways; > > +----+------+------+---------------------------------------+-------+------------+-------+------------+-------+-----------------------+-------------+ > | id | gwid | type | address | strip | > pri_prefix | attrs | probe_mode | state | socket | > description | > > +----+------+------+---------------------------------------+-------+------------+-------+------------+-------+-----------------------+-------------+ > | 1 | gw4 | 3 | fs.3c.com:6080 | 0 | NULL | NULL | > 0 | 0 | udp:192.168.0.69:5060 | NULL | > > +----+------+------+---------------------------------------+-------+------------+-------+------------+-------+-----------------------+-------------+ > > I only have a single Invite on a single session on this leg . There is no > Re-Invite at all . Will I need to set record_route_preset on this case as > well ? > > *Thanks & Regards* > *Sasmita Panda* > *Senior Network Testing and Software Engineer* > *3CLogic , ph:07827611765* > > > On Wed, Jul 24, 2024 at 7:06 PM Ben Newlin <ben.new...@genesys.com> wrote: > >> Sasmita, >> >> >> >> You need to be using $socket_out. [1] >> >> >> >> By default, OpenSIPS will use the receiving socket as the sending socket. >> This means if you receive the message on TLS and do not change $socket_out >> then the message will be sent out the TLS socket. >> >> >> >> Additionally, unless you are using B2BUA or maybe topology_hiding you >> will likely need to “remember” this protocol transition by adding a double >> Record-Route [2] to the message. You may also need to change any >> “transport” params that exist in the Request-URI and possibly the Contact >> header. >> >> >> >> [1] https://www.opensips.org/Documentation/Script-CoreVar-3-2#toc86 >> >> [2] https://opensips.org/docs/modules/3.2.x/rr.html >> >> >> >> Ben Newlin >> >> >> >> *From: *Users <users-boun...@lists.opensips.org> on behalf of Sasmita >> Panda <spa...@3clogic.com> >> *Date: *Wednesday, July 24, 2024 at 1:54 AM >> *To: *OpenSIPS users mailling list <users@lists.opensips.org> >> *Subject: *[OpenSIPS-Users] I need some info while setiing sethostport >> on opensips config . >> >> * EXTERNAL EMAIL - Please use caution with links and attachments * >> >> >> ------------------------------ >> >> Hi All , >> >> >> >> I am using openisp version : 3.2 >> >> >> >> I have an opensips config on which I was listening on UDP port only and >> hence using sethostport to route calls to a particular destination . like >> below . >> >> >> >> if(is_from_gw() || ($rp=~"5505")) >> { >> sethostport("freeswitch-test.xyz.com:6080"); >> route(inbound); >> exit; >> } >> >> >> >> Now I have to accept a call on TLS and send that to some other >> destination on UDP . I have enabled the tls module and also the dependent >> modules like tls_openssl, tls_mgm . >> >> >> >> socket=udp:192.168.0.y:5060 >> socket=tls:192.168.0.y:5061 >> socket=tcp:192.168.0.y:5060 >> >> if(is_from_gw() || ($rp=~"5505")) >> { >> sethostport("freeswitch-test.xyz.com:6080"); >> route(inbound); >> exit; >> } >> >> >> >> This above configuration is not working . I am getting "477 Send Failed " >> >> >> >> *Thanks & Regards* >> >> *Sasmita Panda* >> >> *Senior Network Testing and Software Engineer* >> >> *3CLogic , ph:07827611765* >> _______________________________________________ >> Users mailing list >> Users@lists.opensips.org >> http://lists.opensips.org/cgi-bin/mailman/listinfo/users >> >
_______________________________________________ Users mailing list Users@lists.opensips.org http://lists.opensips.org/cgi-bin/mailman/listinfo/users
