On 2015-11-03 11:28, ioan stan wrote:
Yes, get the “pre-mount” prompt, but fstab is empty as seen below.
[ 9.635227] sd 1:0:0:1: [sdb] Write Protect is off
[ 9.645244] sd 1:0:0:1: [sdb] No Caching mode page found
[ 9.650639] sd 1:0:0:1: [sdb] Assuming drive cache: write through
[ 9.659845] sd 1:0:0:0: [sda] No Caching mode page found
[ 9.665206] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 9.680219] sda: sda1 sda2 sda3 < sda5 >
[ 9.691620] sd 1:0:0:1: [sdb] No Caching mode page found
[ 9.697014] sd 1:0:0:1: [sdb] Assuming drive cache: write through
[ 9.709711] sd 1:0:0:0: [sda] No Caching mode page found
[ 9.715070] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 9.721238] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 9.727862] sdb: sdb1 sdb4
[ 9.742965] sd 1:0:0:1: [sdb] No Caching mode page found
[ 9.748357] sd 1:0:0:1: [sdb] Assuming drive cache: write through
[ 9.754487] sd 1:0:0:1: [sdb] Attached SCSI removable disk
pre-mount:/# ls /etc
cmdline.d group ld.so.conf mtab sysctl.d
conf.d hostid ld.so.conf.d os-release systemd
e2fsck.conf hostname machine-id passwd udev
fstab.empty initrd-release modprobe.d profile virc
fuse.conf ld.so.cache modules-load.d sysctl.conf zfs
pre-mount:/# cat /etc/fstab.empty
pre-mount:/#
Hmm... Something isn't right here. I just went through your log
again and I don't see any reference to zfs-fuse being loaded.
Can you check:
# ps auxw | grep zfs
There should be a process called @sbin/zfs-fuse running.
Is there anything in /sysroot/ ?
Do you have /sbin/zfs-fuse binary?
If zfs-fuse daemon isn't running start it (/sbin/zfs-fuse)
Then do:
# zpool import
That should show you what pools are available (there whould be
one called kirkwood or dreamplug).
Does it work when you _only_ have the RSEL rootfs USB device
plugged in without any other USB devices (i.e. remove whatever
is showing up as /dev/sda).
Gordan
On Nov 3, 2015, at 7:17 PM, Gordan Bobic <[email protected]>
wrote:
On 2015-11-03 03:12, ioan stan wrote:
I was suspecting that fstab needs changes but I couldn't mount the
root partition. Mount command would not work, how would I mount
/dev/sdc1 to /mnt for editing? It seems zfs or zpool would help
but
not sure.
You don't need to modify the image before inserting the card into
the
device. When the boot fails it will drop you to the diagnostic
prompt. Look carefully, it was obscured in your pasted log by kernel
messages from drivers still being loaded.
Hit enter a couple of times and you'll see it. At that point the
rootfs is already mounted and ready to go, just do:
vi /etc/fstab and fix the problem (or comment out the line with
/boot)
then do "reboot" and it should come up OK. You can then fix fstab
properly if you just commented out /boot.
Another question, you're resizing partition with fdisk, parted
would
not work? I did find an article about resizing with fdisk
https://access.redhat.com/articles/1190213 [1] [2]
I am less familiar with parted, I tend to use fdisk (for MBR) and
gdisk (for GPT). If you are more familiar with parted, go for it,
but bear in mind that uboot on *Plugs doesn't support GPT so it is
essential you keep the partition table in MBR format or it won't
work.
Gordan
_______________________________________________
users mailing list
[email protected]
https://lists.redsleeve.org/mailman/listinfo/users
Links:
------
[1] https://access.redhat.com/articles/1190213
_______________________________________________
users mailing list
[email protected]
https://lists.redsleeve.org/mailman/listinfo/users
_______________________________________________
users mailing list
[email protected]
https://lists.redsleeve.org/mailman/listinfo/users
