Fabian, Thanks for the debugging steps.
I did the steps for all three scenarios and created a bug for this: https://bugzilla.redhat.com/show_bug.cgi?id=1010221 Kind Regards, Jorick On Thu, 2013-09-19 at 15:27 +0200, Fabian Deutsch wrote: > Am Donnerstag, den 19.09.2013, 15:12 +0200 schrieb Jorick Astrego: > > Hmmm, I'm beginning to suspect the LSI MegaRaid chips. > > > > I replaced the SSD of the first node with a brand new Samsung 256GB SSD and > > the second node with a 1TB HDD. > > > > When I change the SWAP size on both nodes to 4GB, it fails to install the > > bootloader. > > > > When I leave everything on default and just continue the steps, I get an > > "error 30 read-only filesystem" on BOTH nodes. > > > > When I choose Other drive and select /dev/sda, I get the ValueError > > exception. > > > > So I'm kinda stuck :-& > > > > Our RAID chip is LSI 2108 SAS > > Hey Jorick, > > thanks for the informations from this and your last e-mail. > I think we need some deeper debugging, could you please do the following > to get more debugging informations: > 1. Boot the ISO as usual > 2. When the installer TUI comes up, press F" and drop to a shell > 3. Set a password for root > 4. Now run: ovirt-node-installer --debug > This will run the installer in debug mode (writing tons of infos > to /var/log/ovirt-node.debug.log). > 5. Continue the installation as usual until you reach a problem, then: > > 6. Switch to a second console and login (the setup tui should come up) > 7. Drop to shell by pressing F2 > 8. Please send the files > * /var/log/ovirt-node.debug.log > * /var/log/ovirt.log > * /tmp/ovirt.log (if available) > > That would really help us to find out what the problem is. > > I think we should also open a bug for this. > > Thanks and greetings > fabian > > > Kind regards, > > > > Jorick Astrego > > > > -----Original Message----- > > > From: "Jorick Astrego" <[email protected]> > > > To: "Fabian Deutsch" <[email protected]> > > > Cc: [email protected] > > > Date: 19/09/2013 12:53 > > > Subject: Re: [Users] Exception: ValueError("invalid literal for int() > > > with base 10: ' '", ) > > > > > > Hi, > > > > > > I'm using ovirt-node-iso-3.0.1-1.0.2.vdsm.fc19.iso and I tried > > > reproducing on two nodes. I thought maybe the first node's SSD had failed. > > > > > > See screenshots attached (they are very small). > > > > > > As the Local disk first only reported 1GB, i used Other device /dev/sda > > > and got the ValueError (xxx_144.png). > > > > > > When using Local disk, I get a 'Read-only file system' error. > > > (xxx_145.png) > > > > > > This is on two identical nodes with a SSD connected through LSI MegaRAID. > > > I could try it without RAID, but I'll have to visit the datacenter and > > > reflash the LSI firmware for this. > > > > > > Both nodes had an older 2.6 node image running on it before. > > > > > > After a full RAID re-initialization that produced no errors, I now get > > > yet another faillure: > > > > > > "Exception: RuntimeError('Failed to set install bootloader'.)" > > > (xxx_147.png) > > > > > > Can it be the SSD or RAID controller? I could swap out the SSD for a 2.5 > > > hdd to test it out. > > > > > > Thanks in advance! > > > > > > Jorick Astrego > > > Netbulae B.V. > > > > > > > > > -----Original Message----- > > > > From: "Fabian Deutsch" <[email protected]> > > > > To: "Jorick Astrego" <[email protected]> > > > > Cc: [email protected] > > > > Date: 18/09/2013 15:49 > > > > Subject: Re: [Users] Exception: ValueError("invalid literal for int() > > > > with base 10: ' '", ) > > > > > > > > Hey, > > > > > > > > Am Mittwoch, den 18.09.2013, 15:35 +0200 schrieb Jorick Astrego: > > > > > I'm trying to deploy the ovirt node 3.0.1-1.0.2 image. Because we > > > > > only have a small SSD and don't need overcommit I changed the swap > > > > > file size to a smaller value. > > > > > > > > > > While installing I now get the following error and have to reboot: > > > > > > > > > > Exception: ValueError("invalid literal for int() with base 10: ' '",) > > > > > > > > I tried to reproduce this problem but couldn't trigger it using: > > > > 1. Enter the storage sizes page > > > > 2. Changed the swap value to 100 (allowed value depends on your hosts > > > > mem size) > > > > 3. Saved page, went through the next pages and installed > > > > > > > > Could you explain in detail how you triggered this problem? > > > > And are you using the fc19 or el6 iso? > > > > > > > > Greetings > > > > fabian > > > > > > > > > > > > > If I don't change the value of the swap, I get a message that the > > > > > installer is unable to format/partition the disk. > > > > > > > > > > Kind regards, > > > > > > > > > > Jorick Astrego > > > > > > > > > > > > > > > > > > > > > > > > > _______________________________________________ > > > > > Users mailing list > > > > > [email protected] > > > > > http://lists.ovirt.org/mailman/listinfo/users > > > > > > > > > > > _______________________________________________ > > > Users mailing list > > > [email protected] > > > http://lists.ovirt.org/mailman/listinfo/users > > > > > > > > > > > _______________________________________________ Users mailing list [email protected] http://lists.ovirt.org/mailman/listinfo/users
