On Wed, 2014-01-22 at 15:13 +0000, Dan Kenigsberg wrote: > On Wed, Jan 22, 2014 at 07:43:52AM +0000, Karli Sjöberg wrote: > > On Tue, 2014-01-21 at 21:22 -0300, Federico Sayd wrote: > > > Hello: > > > > > > I am having problems with bonding > > > > > > I have installed Centos 6.5 in order to use it as host. I configured > > > eth0 with the vlan of the management network (Vlan 70). Then I > > > registered the host to the engine (3.3.2-1-el6) and the engine > > > installed oVirt in the host without problem. Ovirtmgmt was created > > > automatically and bridged with eth0.70. > > > > > > Now I need to bond a second network interface (eth1) with eth0. But > > > when I try to bond the nics, I get the next error: > > > > > > "A slave interface is not properly configured. Please verify slaves do > > > not contain any of the following properties: network name, boot > > > protocol, IP address, netmask, gateway or vlan-ID notation (as part of > > > interface's name or explicitly)" > > Federico, where exactly do you get this error? Would you attach the > setupNetwork log from supervdsmd.log? > > > > > > > I delete any unnecessary parameters from ifcfg-eth0 and ifcfg-eth1. > > > > > > This is my network config: > > > > > > ifcfg-eth0: > > > DEVICE=eth0 > > > TYPE=Ethernet > > > ONBOOT=yes > > > > > > ifcfg-eth1: > > > DEVIC E=eth1 > > > TYPE=Ethernet > > > ONBOOT=yes > > > > > > ifcfg-eth0.70: > > > # Generated by VDSM version 4.13.2-1.el6 > > > DEVICE=eth0.70 > > > ONBOOT=yes > > > VLAN=yes > > > BRIDGE=ovirtmgmt > > > NM_CONTROLLED=no > > > STP=no > > > > > > ifcfg-ovirtmgmt: > > > # Generated by VDSM version 4.13.2-1.el6 > > > DEVICE=ovirtmgmt > > > ONBOOT=yes > > > TYPE=Bridge > > > DELAY=0 > > > IPADDR=192.168.1.101 > > > NETMASK=255.255.255.0 > > > BOOTPROTO=none > > > DEFROUTE=yes > > > NM_CONTROLLED=no > > > STP=no > > > > > > No others ifcfg-* files. > > > > > > I don't see the parameters that oVirt doesn't like. Any clue, > > > workaround, bug report....? > > > > > > Thanks! > > > > > > Federico > > > > > > PD: Sorry for my basic english > > > > > > > I´ve seen issues from folks trying to configure Host network through > > webadmin and failing one too many times now, so I decided to write > > something up: > > > > http://www.ovirt.org/Bonding_VLAN_Bridge > > > > Hope this helps! > > Thanks Karli! Though it SHOULD be possible to start with eth0 and eth0.2 > on the host (where "2" is the vlan id of your manamgement network), and > from there on, do all configuration via Engine. > > I'd like to automate as much as possible out of this process, and iron > out remaining bugs. Hence, I would like to hear more about Federico's > mode of failure.
Couldn´t agree with you more. But it´s always good to have something to fall back on, if only as reference, I think. > > One comment to your wiki page: in order to better intergrate with our > recent source-routing support (mostly useful for display network), > please set GATEWAY only in ifcfg-ovirtmgmt, and remember to set > DEFROUTE=no in any other ifcfg that mentions IPADDR so as not to > override the default. > > Dan. Does that imply that default gateway is supposed to be on the same net as ovirtmgmt? -- Med Vänliga Hälsningar ------------------------------------------------------------------------------- Karli Sjöberg Swedish University of Agricultural Sciences Box 7079 (Visiting Address Kronåsvägen 8) S-750 07 Uppsala, Sweden Phone: +46-(0)18-67 15 66 karli.sjob...@slu.se _______________________________________________ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users _______________________________________________ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users