Hi
The rpm packages you listed in the other mail are installed but I had
not run vdsm-tool ovn-config to create tunnel as the OVN controller is
on the same host.
[root@h2 ~]# rpm -q openvswitch-ovn-common
openvswitch-ovn-common-2.6.90-1.el7.centos.x86_64
[root@h2 ~]# rpm -q openvswitch-ovn-host
openvswitch-ovn-host-2.6.90-1.el7.centos.x86_64
[root@h2 ~]# rpm -q python-openvswitch
python-openvswitch-2.6.90-1.el7.centos.noarch
After removing my manually created br-int and run
vdsm-tool ovn-config 127.0.0.1 172.27.1.1
then I have the br-int but 'ip link show' does not show any link
'genev_sys_' nor does 'ovs-vsctl show' any port for ovn. I assume these
are when there is an actual tunnel?
[root@h2 ~]# ovs-vsctl show
ebb6aede-cbbc-4f4f-a88a-a9cd72b2bd23
Bridge br-int
fail_mode: secure
Port br-int
Interface br-int
type: internal
Bridge ovirtbridge
Port ovirtbridge
Interface ovirtbridge
type: internal
Bridge "ovsbridge0"
Port "ovsbridge0"
Interface "ovsbridge0"
type: internal
Port "eth0"
Interface "eth0"
ovs_version: "2.6.90"
[root@h2 ~]# ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode
DEFAULT qlen 1
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
master ovs-system state UP mode DEFAULT qlen 1000
link/ether 44:8a:5b:84:7d:b3 brd ff:ff:ff:ff:ff:ff
3: ovs-system: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 5a:14:cf:28:47:e2 brd ff:ff:ff:ff:ff:ff
4: ovsbridge0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue
state UNKNOWN mode DEFAULT qlen 1000
link/ether 44:8a:5b:84:7d:b3 brd ff:ff:ff:ff:ff:ff
5: br-int: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 9e:b0:3a:9d:f2:4b brd ff:ff:ff:ff:ff:ff
6: ovirtbridge: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue
state UNKNOWN mode DEFAULT qlen 1000
link/ether a6:f6:e5:a4:5b:45 brd ff:ff:ff:ff:ff:ff
7: dummy0: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue master
ovirtmgmt state UNKNOWN mode DEFAULT qlen 1000
link/ether 66:e0:1c:c3:a9:d8 brd ff:ff:ff:ff:ff:ff
8: ovirtmgmt: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue
state UP mode DEFAULT qlen 1000
link/ether 66:e0:1c:c3:a9:d8 brd ff:ff:ff:ff:ff:ff
Firewall settings:
[root@h2 ~]# firewall-cmd --list-all-zones
work
target: default
icmp-block-inversion: no
interfaces:
sources:
services: dhcpv6-client ssh
ports:
protocols:
masquerade: no
forward-ports:
sourceports:
icmp-blocks:
rich rules:
drop
target: DROP
icmp-block-inversion: no
interfaces:
sources:
services:
ports:
protocols:
masquerade: no
forward-ports:
sourceports:
icmp-blocks:
rich rules:
internal
target: default
icmp-block-inversion: no
interfaces:
sources:
services: dhcpv6-client mdns samba-client ssh
ports:
protocols:
masquerade: no
forward-ports:
sourceports:
icmp-blocks:
rich rules:
external
target: default
icmp-block-inversion: no
interfaces:
sources:
services: ssh
ports:
protocols:
masquerade: yes
forward-ports:
sourceports:
icmp-blocks:
rich rules:
trusted
target: ACCEPT
icmp-block-inversion: no
interfaces:
sources:
services:
ports:
protocols:
masquerade: no
forward-ports:
sourceports:
icmp-blocks:
rich rules:
home
target: default
icmp-block-inversion: no
interfaces:
sources:
services: dhcpv6-client mdns samba-client ssh
ports:
protocols:
masquerade: no
forward-ports:
sourceports:
icmp-blocks:
rich rules:
dmz
target: default
icmp-block-inversion: no
interfaces:
sources:
services: ssh
ports:
protocols:
masquerade: no
forward-ports:
sourceports:
icmp-blocks:
rich rules:
public (active)
target: default
icmp-block-inversion: no
interfaces: eth0 ovsbridge0
sources:
services: dhcpv6-client ssh
ports:
protocols:
masquerade: no
forward-ports:
sourceports:
icmp-blocks:
rich rules:
block
target: %%REJECT%%
icmp-block-inversion: no
interfaces:
sources:
services:
ports:
protocols:
masquerade: no
forward-ports:
sourceports:
icmp-blocks:
rich rules:
ovirt (active)
target: default
icmp-block-inversion: no
interfaces: ovirtbridge ovirtmgmt
sources:
services: dhcp ovirt-fence-kdump-listener ovirt-http ovirt-https
ovirt-imageio-proxy ovirt-postgres ovirt-provider-ovn
ovirt-vmconsole-proxy ovirt-websocket-proxy ssh vdsm
ports:
protocols:
masquerade: yes
forward-ports:
sourceports:
icmp-blocks:
rich rules:
rule family="ipv4" port port="6641" protocol="tcp" accept
rule family="ipv4" port port="6642" protocol="tcp" accept
The db dump is attached
/Sverker
Den 2016-12-29 kl. 09:50, skrev Marcin Mirecki:
Hi,
Can you please do: "sudo ovsdb-client dump"
on the host and send me the output?
Have you configured the ovn controller to connect to the
OVN north? You can do it using "vdsm-tool ovn-config" or
using the OVN tools directly.
Please check out: https://www.ovirt.org/blog/2016/11/ovirt-provider-ovn/
for details.
Also please note that the OVN provider is completely different
from the neutron-openvswitch plugin. Please don't mix the two.
Marcin
----- Original Message -----
From: "Marcin Mirecki" <[email protected]>
To: "Sverker Abrahamsson" <[email protected]>
Cc: "Ovirt Users" <[email protected]>
Sent: Thursday, December 29, 2016 9:27:19 AM
Subject: Re: [ovirt-users] Issue with OVN/OVS and mandatory ovirtmgmt network
Hi,
br-int is the OVN integration bridge, it should have been created
when installing OVN. I assume you have the following packages installed
on the host:
openvswitch-ovn-common
openvswitch-ovn-host
python-openvswitch
Please give me some time to look at the connectivity problem.
Marcin
----- Original Message -----
From: "Sverker Abrahamsson" <[email protected]>
To: "Marcin Mirecki" <[email protected]>
Cc: "Ovirt Users" <[email protected]>
Sent: Thursday, December 29, 2016 12:47:04 AM
Subject: Re: [ovirt-users] Issue with OVN/OVS and mandatory ovirtmgmt
network
From
/usr/libexec/vdsm/hooks/before_device_create/ovirt_provider_ovn_hook
(installed by ovirt-provider-ovn-driver rpm):
BRIDGE_NAME = 'br-int'
Den 2016-12-28 kl. 23:56, skrev Sverker Abrahamsson:
Googling on the message about br-int suggested adding that bridge to ovs:
ovs-vsctl add-br br-int
Then the VM is able to boot, but it fails to get network connectivity.
Output in /var/log/messages:
Dec 28 23:31:35 h2 ovs-vsctl: ovs|00001|vsctl|INFO|Called as ovs-vsctl
--timeout=5 -- --if-exists del-port vnet0 -- add-port br-int vnet0 --
set Interface vnet0 "external-ids:attached-mac=\"00:1a:4a:16:01:51\""
-- set Interface vnet0
"external-ids:iface-id=\"e8853aac-8a75-41b0-8010-e630017dcdd8\"" --
set Interface vnet0
"external-ids:vm-id=\"b9440d60-ef5a-4e2b-83cf-081df7c09e6f\"" -- set
Interface vnet0 external-ids:iface-status=active
Dec 28 23:31:35 h2 kernel: device vnet0 entered promiscuous mode
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ebtables --concurrent -t nat -D PREROUTING -i vnet0 -j
libvirt-J-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ebtables --concurrent -t nat -D POSTROUTING -o vnet0 -j
libvirt-P-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ebtables --concurrent -t nat -L libvirt-J-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ebtables --concurrent -t nat -L libvirt-P-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ebtables --concurrent -t nat -F libvirt-J-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ebtables --concurrent -t nat -X libvirt-J-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ebtables --concurrent -t nat -F libvirt-P-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ebtables --concurrent -t nat -X libvirt-P-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ebtables --concurrent -t nat -F J-vnet0-mac' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ebtables --concurrent -t nat -X J-vnet0-mac' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ebtables --concurrent -t nat -F J-vnet0-arp-mac' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ebtables --concurrent -t nat -X J-vnet0-arp-mac' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/iptables -w2 -w -D libvirt-out -m physdev
--physdev-is-bridged --physdev-out vnet0 -g FO-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/iptables -w2 -w -D libvirt-out -m physdev --physdev-out
vnet0 -g FO-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/iptables -w2 -w -D libvirt-in -m physdev --physdev-in vnet0
-g FI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/iptables -w2 -w -D libvirt-host-in -m physdev --physdev-in
vnet0 -g HI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/iptables -w2 -w -F FO-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/iptables -w2 -w -X FO-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/iptables -w2 -w -F FI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/iptables -w2 -w -X FI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/iptables -w2 -w -F HI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/iptables -w2 -w -X HI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/iptables -w2 -w -E FP-vnet0 FO-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/iptables -w2 -w -E FJ-vnet0 FI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/iptables -w2 -w -E HJ-vnet0 HI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ip6tables -w2 -w -D libvirt-out -m physdev
--physdev-is-bridged --physdev-out vnet0 -g FO-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ip6tables -w2 -w -D libvirt-out -m physdev --physdev-out
vnet0 -g FO-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ip6tables -w2 -w -D libvirt-in -m physdev --physdev-in
vnet0 -g FI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ip6tables -w2 -w -D libvirt-host-in -m physdev --physdev-in
vnet0 -g HI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ip6tables -w2 -w -F FO-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ip6tables -w2 -w -X FO-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ip6tables -w2 -w -F FI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ip6tables -w2 -w -X FI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ip6tables -w2 -w -F HI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ip6tables -w2 -w -X HI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ip6tables -w2 -w -E FP-vnet0 FO-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ip6tables -w2 -w -E FJ-vnet0 FI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ip6tables -w2 -w -E HJ-vnet0 HI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ebtables --concurrent -t nat -D PREROUTING -i vnet0 -j
libvirt-I-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ebtables --concurrent -t nat -D POSTROUTING -o vnet0 -j
libvirt-O-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ebtables --concurrent -t nat -L libvirt-I-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ebtables --concurrent -t nat -L libvirt-O-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ebtables --concurrent -t nat -F libvirt-I-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ebtables --concurrent -t nat -X libvirt-I-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ebtables --concurrent -t nat -F libvirt-O-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ebtables --concurrent -t nat -X libvirt-O-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ebtables --concurrent -t nat -L libvirt-P-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ebtables --concurrent -t nat -E libvirt-P-vnet0
libvirt-O-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ebtables --concurrent -t nat -F I-vnet0-mac' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ebtables --concurrent -t nat -X I-vnet0-mac' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ebtables --concurrent -t nat -F I-vnet0-arp-mac' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED:
'/usr/sbin/ebtables --concurrent -t nat -X I-vnet0-arp-mac' failed:
[root@h2 etc]# ovs-vsctl show
ebb6aede-cbbc-4f4f-a88a-a9cd72b2bd23
Bridge ovirtbridge
Port "ovirtport0"
Interface "ovirtport0"
type: internal
Port ovirtbridge
Interface ovirtbridge
type: internal
Bridge "ovsbridge0"
Port "ovsbridge0"
Interface "ovsbridge0"
type: internal
Port "eth0"
Interface "eth0"
Bridge br-int
Port br-int
Interface br-int
type: internal
Port "vnet0"
Interface "vnet0"
ovs_version: "2.6.90"
Searching through the code it appears that br-int comes from
neutron-openvswitch plugin ??
[root@h2 share]# rpm -qf
/usr/share/otopi/plugins/ovirt-host-deploy/openstack/neutron_openvswitch.py
ovirt-host-deploy-1.6.0-0.0.master.20161215101008.gitb76ad50.el7.centos.noarch
/Sverker
Den 2016-12-28 kl. 23:24, skrev Sverker Abrahamsson:
In addition I had to add an alias to modprobe:
[root@h2 modprobe.d]# cat dummy.conf
alias dummy0 dummy
Den 2016-12-28 kl. 23:03, skrev Sverker Abrahamsson:
Hi
I first tried to set device name to dummy_0, but then ifup did not
succeed in creating the device unless I first did 'ip link add
dummy_0 type dummy' but then it would not suceed to establish the if
on reboot.
Setting fake_nics = dummy0 would not work neither, but this works:
fake_nics = dummy*
The engine is now able to find the if and assign bridge ovirtmgmt to
it.
However, I then run into the next issue when starting a VM:
2016-12-28 22:28:23,897 ERROR
[org.ovirt.engine.core.dal.dbbroker.auditloghandling.AuditLogDirector]
(ForkJoinPool-1-worker-2) [] Correlation ID: null, Call Stack: null,
Custom Event ID: -1, Message: VM CentOS7 is down with error. Exit
message: Cannot get interface MTU on 'br-int': No such device.
This VM has a nic on ovirtbridge, which comes from the OVN provider.
/Sverker
Den 2016-12-28 kl. 14:38, skrev Marcin Mirecki:
Sverker,
Can you try adding a vnic named veth_* or dummy_*,
(or alternatively add the name of the vnic to
vdsm.config fake_nics), and setup the management
network using this vnic?
I suppose adding the vnic you use for connecting
to the engine to fake_nics should make it visible
to the engine, and you should be able to use it for
the setup.
Marcin
----- Original Message -----
From: "Marcin Mirecki" <[email protected]>
To: "Sverker Abrahamsson" <[email protected]>
Cc: "Ovirt Users" <[email protected]>
Sent: Wednesday, December 28, 2016 12:06:26 PM
Subject: Re: [ovirt-users] Issue with OVN/OVS and mandatory
ovirtmgmt network
I have an internal OVS bridge called ovirtbridge which has a port
with
IP address, but in the host network settings that port is not
visible.
I just verified and unfortunately the virtual ports are not
visible in engine
to assign a network to :(
I'm afraid that the engine is not ready for such a scenario (even
if it
works).
Please give me some time to look for a solution.
----- Original Message -----
From: "Sverker Abrahamsson" <[email protected]>
To: "Marcin Mirecki" <[email protected]>
Cc: "Ovirt Users" <[email protected]>
Sent: Wednesday, December 28, 2016 11:48:24 AM
Subject: Re: [ovirt-users] Issue with OVN/OVS and mandatory
ovirtmgmt
network
Hi Marcin
Yes, that is my issue. I don't want to let ovirt/vdsm see eth0 nor
ovsbridge0 since as soon as it sees them it messes up the network
config
so that the host will be unreachable.
I have an internal OVS bridge called ovirtbridge which has a port
with
IP address, but in the host network settings that port is not
visible.
It doesn't help to name it ovirtmgmt.
The engine is able to communicate with the host on the ip it has
been
given, it's just that it believes that it HAS to have a ovirtmgmt
network which can't be on OVN.
/Sverker
Den 2016-12-28 kl. 10:45, skrev Marcin Mirecki:
Hi Sverker,
The management network is mandatory on each host. It's used by the
engine to communicate with the host.
Looking at your description and the exception it looks like it is
missing.
The error is caused by not having any network for the host
(network list retrieved in
InterfaceDaoImpl.getHostNetworksByCluster -
which
gets all the networks on nics for a host from vds_interface
table in the
DB).
Could you maybe create a virtual nic connected to ovsbridge0 (as I
understand you
have no physical nic available) and use this for the management
network?
I then create a bridge for use with ovirt, with a private address.
I'm not quite sure I understand. Is this yet another bridge
connected to
ovsbridge0?
You could also attach the vnic for the management network here
if need
be.
Please keep in mind that OVN has no use in setting up the
management
network.
The OVN provider can only handle external networks, which can
not be used
for a
management network.
Marcin
----- Original Message -----
From: "Sverker Abrahamsson" <[email protected]>
To: [email protected]
Sent: Wednesday, December 28, 2016 12:39:59 AM
Subject: [ovirt-users] Issue with OVN/OVS and mandatory ovirtmgmt
network
Hi
For long time I've been looking for proper support in ovirt for
Open
vSwitch
so I'm happy that it is moving in the right direction. However,
there
seems
to still be a dependency on a ovirtmgmt bridge and I'm unable
to move
that
to the OVN provider.
The hosting center where I rent hw instances has a bit special
network
setup,
so I have one physical network port with a /32 netmask and
point-to-point
config to router. The physical port I connect to a ovs bridge
which has
the
public ip. Since ovirt always messes up the network config when
I've
tried
to let it have access to the network config for the physical
port, I've
set
eht0 and ovsbridge0 as hidden in vdsm.conf.
I then create a bridge for use with ovirt, with a private
address. With
the
OVN provider I am now able to import these into the engine and
it looks
good. When creating a VM I can select that it will have a vNic
on my OVS
bridge.
However, I can't start the VM as an exception is thrown in the
log:
2016-12-28 00:13:33,350 ERROR
[org.ovirt.engine.core.bll.RunVmCommand]
(default task-5) [3c882d53] Error during ValidateFailure.:
java.lang.NullPointerException
at
org.ovirt.engine.core.bll.scheduling.policyunits.NetworkPolicyUnit.validateRequiredNetworksAvailable(NetworkPolicyUnit.java:140)
[bll.jar:]
at
org.ovirt.engine.core.bll.scheduling.policyunits.NetworkPolicyUnit.filter(NetworkPolicyUnit.java:69)
[bll.jar:]
at
org.ovirt.engine.core.bll.scheduling.SchedulingManager.runInternalFilters(SchedulingManager.java:597)
[bll.jar:]
at
org.ovirt.engine.core.bll.scheduling.SchedulingManager.runFilters(SchedulingManager.java:564)
[bll.jar:]
at
org.ovirt.engine.core.bll.scheduling.SchedulingManager.canSchedule(SchedulingManager.java:494)
[bll.jar:]
at
org.ovirt.engine.core.bll.validator.RunVmValidator.canRunVm(RunVmValidator.java:133)
[bll.jar:]
at
org.ovirt.engine.core.bll.RunVmCommand.validate(RunVmCommand.java:940)
[bll.jar:]
at
org.ovirt.engine.core.bll.CommandBase.internalValidate(CommandBase.java:886)
[bll.jar:]
at
org.ovirt.engine.core.bll.CommandBase.validateOnly(CommandBase.java:366)
[bll.jar:]
at
org.ovirt.engine.core.bll.PrevalidatingMultipleActionsRunner.canRunActions(PrevalidatingMultipleActionsRunner.java:113)
[bll.jar:]
at
org.ovirt.engine.core.bll.PrevalidatingMultipleActionsRunner.invokeCommands(PrevalidatingMultipleActionsRunner.java:99)
[bll.jar:]
at
org.ovirt.engine.core.bll.PrevalidatingMultipleActionsRunner.execute(PrevalidatingMultipleActionsRunner.java:76)
[bll.jar:]
at
org.ovirt.engine.core.bll.Backend.runMultipleActionsImpl(Backend.java:613)
[bll.jar:]
at
org.ovirt.engine.core.bll.Backend.runMultipleActions(Backend.java:583)
[bll.jar:]
Looking at that section of code where the exception is thrown,
I see
that
it
iterates over host networks to find required networks, which I
assume is
ovirtmgmt. In the host network setup dialog I don't see any
networks at
all
but it lists ovirtmgmt as required. It also list the OVN
networks but
these
can't be statically assigned as they are added dynamically when
needed,
which is fine.
I believe that I either need to remove ovirtmgmt network or
configure
that
it
is provided by the OVN provider, but neither is possible.
Preferably it
shouldn't be hardcoded which network is management and
mandatory but be
possible to configure.
/Sverker
Den 2016-12-27 kl. 17:10, skrev Marcin Mirecki:
_______________________________________________
Users mailing list
[email protected]
http://lists.ovirt.org/mailman/listinfo/users
_______________________________________________
Users mailing list
[email protected]
http://lists.ovirt.org/mailman/listinfo/users
_______________________________________________
Users mailing list
[email protected]
http://lists.ovirt.org/mailman/listinfo/users
_______________________________________________
Users mailing list
[email protected]
http://lists.ovirt.org/mailman/listinfo/users
_______________________________________________
Users mailing list
[email protected]
http://lists.ovirt.org/mailman/listinfo/users
AutoAttach table
_uuid mappings system_description system_name
----- -------- ------------------ -----------
Bridge table
_uuid auto_attach controller datapath_id
datapath_type datapath_version external_ids fail_mode flood_vlans flow_tables
ipfix mcast_snooping_enable mirrors name netflow other_config
ports
protocols rstp_enable rstp_status sflow status stp_enable
------------------------------------ ----------- ---------- ------------------
------------- ---------------- ------------ --------- ----------- -----------
----- --------------------- ------- ------------ -------
------------------------
----------------------------------------------------------------------------
--------- ----------- ----------- ----- ------ ----------
d4af5bbb-df14-4ffc-aae9-b6566a5ffd87 [] [] "0000448a5b847db3"
"" "<unknown>" {} [] [] {}
[] false [] "ovsbridge0" [] {}
[a7cca8f5-3437-43dc-8310-195454fb7771, b7361c57-41aa-4a8f-b6fe-67e643129aca]
[] false {} [] {} false
9d3ab09e-a146-4bf2-a5bb-ba9948c4f2dd [] [] "00009eb03a9df24b"
"" "<unknown>" {} secure [] {}
[] false [] br-int []
{disable-in-band="true"} [406caf72-a6f9-4fd8-83dc-2bc4fb21944c]
[] false {} [] {} false
a4e5f6a5-4ec1-455b-98e9-8b5e6a8b4cc4 [] [] "0000a6f6e5a45b45"
"" "<unknown>" {} [] [] {}
[] false [] ovirtbridge [] {}
[7b45917b-abaf-4ebd-b501-ce76f07fe65e]
[] false {} [] {} false
Controller table
_uuid connection_mode controller_burst_limit controller_rate_limit
enable_async_messages external_ids inactivity_probe is_connected local_gateway
local_ip local_netmask max_backoff other_config role status target
----- --------------- ---------------------- ---------------------
--------------------- ------------ ---------------- ------------ -------------
-------- ------------- ----------- ------------ ---- ------ ------
Flow_Sample_Collector_Set table
_uuid bridge external_ids id ipfix
----- ------ ------------ -- -----
Flow_Table table
_uuid external_ids flow_limit groups name overflow_policy prefixes
----- ------------ ---------- ------ ---- --------------- --------
IPFIX table
_uuid cache_active_timeout cache_max_flows external_ids obs_domain_id
obs_point_id other_config sampling targets
----- -------------------- --------------- ------------ -------------
------------ ------------ -------- -------
Interface table
_uuid admin_state bfd bfd_status cfm_fault
cfm_fault_status cfm_flap_count cfm_health cfm_mpid cfm_remote_mpids
cfm_remote_opstate duplex error external_ids ifindex ingress_policing_burst
ingress_policing_rate lacp_current link_resets link_speed link_state lldp mac
mac_in_use mtu mtu_request name ofport ofport_request options
other_config statistics
status
type
------------------------------------ ----------- --- ---------- ---------
---------------- -------------- ---------- -------- ----------------
------------------ ------ ----- ------------ ------- ----------------------
--------------------- ------------ ----------- ---------- ---------- ---- ---
------------------- ---- ----------- ------------ ------ -------------- -------
------------
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
-----------------------------------------------------------------------
--------
db4ffac0-fd98-4143-91c0-3ca4767ebc52 down {} {} [] []
[] [] [] [] []
[] [] {} 5 0 0
[] 0 [] down {} [] "9e:b0:3a:9d:f2:4b"
1500 [] br-int 65534 [] {} {}
{collisions=0, rx_bytes=0, rx_crc_err=0, rx_dropped=0, rx_errors=0,
rx_frame_err=0, rx_over_err=0, rx_packets=0, tx_bytes=0, tx_dropped=0,
tx_errors=0, tx_packets=0} {driver_name=openvswitch}
internal
21df7a58-e572-4042-8b64-6370d8e58f92 up {} {} [] []
[] [] [] [] []
[] [] {} 4 0 0
[] 1 [] up {} [] "44:8a:5b:84:7d:b3"
1500 [] "ovsbridge0" 65534 [] {} {}
{collisions=0, rx_bytes=193718, rx_crc_err=0, rx_dropped=39, rx_errors=0,
rx_frame_err=0, rx_over_err=0, rx_packets=2672, tx_bytes=32719, tx_dropped=0,
tx_errors=0, tx_packets=248} {driver_name=openvswitch}
internal
d8c5780d-b9bb-477a-8732-b29c28020831 up {} {} [] []
[] [] [] [] []
[] [] {} 6 0 0
[] 1 [] up {} [] "a6:f6:e5:a4:5b:45"
1500 [] ovirtbridge 65534 [] {} {}
{collisions=0, rx_bytes=0, rx_crc_err=0, rx_dropped=0, rx_errors=0,
rx_frame_err=0, rx_over_err=0, rx_packets=0, tx_bytes=822, tx_dropped=0,
tx_errors=0, tx_packets=13} {driver_name=openvswitch}
internal
0ac4a1a4-1f06-4ba6-b013-c4fb454f315c up {} {} [] []
[] [] [] [] []
full [] {} 2 0 0
[] 1 1000000000 up {} [] "44:8a:5b:84:7d:b3"
1500 [] "eth0" 1 [] {} {}
{collisions=0, rx_bytes=234394, rx_crc_err=0, rx_dropped=0, rx_errors=0,
rx_frame_err=0, rx_over_err=0, rx_packets=2711, tx_bytes=33603, tx_dropped=0,
tx_errors=0, tx_packets=257} {driver_name="r8169",
driver_version="2.3LK-NAPI", firmware_version=""} ""
Manager table
_uuid connection_mode external_ids inactivity_probe is_connected max_backoff
other_config status target
----- --------------- ------------ ---------------- ------------ -----------
------------ ------ ------
Mirror table
_uuid external_ids name output_port output_vlan select_all select_dst_port
select_src_port select_vlan snaplen statistics
----- ------------ ---- ----------- ----------- ---------- ---------------
--------------- ----------- ------- ----------
NetFlow table
_uuid active_timeout add_id_to_interface engine_id engine_type external_ids
targets
----- -------------- ------------------- --------- ----------- ------------
-------
Open_vSwitch table
_uuid bridges
cur_cfg
datapath_types db_version external_ids
iface_types
manager_options next_cfg other_config ovs_version ssl statistics
system_type system_version
------------------------------------
------------------------------------------------------------------------------------------------------------------
------- ---------------- ----------
--------------------------------------------------------------------------------------------------------------------------------------------------------------------
------------------------------------------------------------- ---------------
-------- ------------ ----------- --- ---------- ----------- --------------
ebb6aede-cbbc-4f4f-a88a-a9cd72b2bd23 [9d3ab09e-a146-4bf2-a5bb-ba9948c4f2dd,
a4e5f6a5-4ec1-455b-98e9-8b5e6a8b4cc4, d4af5bbb-df14-4ffc-aae9-b6566a5ffd87] 68
[netdev, system] "7.14.0" {hostname="h2.limetransit.com",
ovn-encap-ip="172.27.1.1", ovn-encap-type=geneve,
ovn-remote="tcp:127.0.0.1:6642",
system-id="6e4dd29f-7607-48d7-8e5a-eef4c6aeefb5"} [geneve, gre, internal, lisp,
patch, stt, system, tap, vxlan] [] 68 {} "2.6.90"
[] {} centos "7"
Port table
_uuid bond_active_slave bond_downdelay
bond_fake_iface bond_mode bond_updelay external_ids fake_bridge interfaces
lacp mac name other_config protected qos
rstp_statistics rstp_status statistics status tag trunks vlan_mode
------------------------------------ ----------------- --------------
--------------- --------- ------------ ------------ -----------
-------------------------------------- ---- --- ------------ ------------
--------- --- --------------- ----------- ---------- ------ --- ------ ---------
406caf72-a6f9-4fd8-83dc-2bc4fb21944c [] 0 false
[] 0 {} false
[db4ffac0-fd98-4143-91c0-3ca4767ebc52] [] [] br-int {} false
[] {} {} {} {} [] [] []
b7361c57-41aa-4a8f-b6fe-67e643129aca [] 0 false
[] 0 {} false
[0ac4a1a4-1f06-4ba6-b013-c4fb454f315c] [] [] "eth0" {} false
[] {} {} {} {} [] [] []
7b45917b-abaf-4ebd-b501-ce76f07fe65e [] 0 false
[] 0 {} false
[d8c5780d-b9bb-477a-8732-b29c28020831] [] [] ovirtbridge {} false
[] {} {} {} {} [] [] []
a7cca8f5-3437-43dc-8310-195454fb7771 [] 0 false
[] 0 {} false
[21df7a58-e572-4042-8b64-6370d8e58f92] [] [] "ovsbridge0" {} false
[] {} {} {} {} [] [] []
QoS table
_uuid external_ids other_config queues type
----- ------------ ------------ ------ ----
Queue table
_uuid dscp external_ids other_config
----- ---- ------------ ------------
SSL table
_uuid bootstrap_ca_cert ca_cert certificate external_ids private_key
----- ----------------- ------- ----------- ------------ -----------
sFlow table
_uuid agent external_ids header polling sampling targets
----- ----- ------------ ------ ------- -------- -------
_______________________________________________
Users mailing list
[email protected]
http://lists.ovirt.org/mailman/listinfo/users
