I totally missed that. Thanks, that clears it up!
On Mon, Apr 9, 2018 at 12:29 PM, Dominik Holler <[email protected]> wrote: > Different logical networks in oVirt attached to the same host should use > different IP networks. > > On Mon, 9 Apr 2018 09:16:49 -0700 > Cole Johnson <[email protected]> wrote: > >> If I mouse over the ovirtmgmt label in "Setup Host", it indicates that >> it is the default route. Please see the attached screen shot. The >> output of ip route in the terminal shows: >> >> [root@kerensk ~]# ip route >> default via 10.0.0.1 dev eno2 proto static metric 100 >> default via 10.0.0.1 dev eno3 proto static metric 101 >> 10.0.0.0/24 dev ovirtmgmt proto kernel scope link src 10.0.0.240 >> 10.0.0.0/24 dev gluster proto kernel scope link src 10.0.0.243 >> 10.0.0.0/24 dev eno2 proto kernel scope link src 10.0.0.241 metric 100 >> 10.0.0.0/24 dev eno3 proto kernel scope link src 10.0.0.242 metric 101 >> 169.254.0.0/16 dev ovirtmgmt scope link metric 1021 >> 169.254.0.0/16 dev gluster scope link metric 1028 >> >> On Mon, Apr 9, 2018 at 8:20 AM, Dominik Holler <[email protected]> >> wrote: >> > On Mon, 9 Apr 2018 07:39:13 -0700 >> > Cole Johnson <[email protected]> wrote: >> > >> >> Where can I find this information? The best I can find is if I am >> >> in the "Setup Host" dialog, and mouse over the un-synced network. >> >> The message reads "Host Network's configurations differ from DC". >> > >> > The table below this message in dialog.jpeg shows the values not in >> > sync, which is the default route of the host. >> > >> >> If this >> >> is the error message, what do I need to do to make the >> >> configurations match? >> > >> > Ensure that the gateway of ovirtmgt is the default route on the >> > host. >> >> Isn't this the whole point of what I am trying to do here? I >> >> have attached some screenshots of the different messages that I >> >> encounter. >> >> >> >> On Mon, Apr 9, 2018 at 12:54 AM, Dominik Holler >> >> <[email protected]> wrote: >> >> > On Wed, 4 Apr 2018 11:19:33 -0700 >> >> > Cole Johnson <[email protected]> wrote: >> >> > >> >> >> Hello, >> >> >> I am trying to set up a 3 host gluster hyperconverged self >> >> >> hosted engine running on oVirt Nodes. ( I think that I have all >> >> >> of the buzzwords here) All of the hardware is the same. I am >> >> >> using the guide from here: >> >> >> https://www.ovirt.org/blog/2018/02/up-and-running-with-ovirt-4-2-and-gluster-storage/ >> >> >> and the documentation here: >> >> >> https://www.ovirt.org/documentation/gluster-hyperconverged/Gluster_Hyperconverged_Guide/ >> >> >> for reference. >> >> >> I have used the setup wizards from the cockpit interface to >> >> >> setup gluster and the hosted engine successfully. I have >> >> >> configured the gluster storage and setup all of the hosts >> >> >> inside the hosted engine. >> >> >> >> >> >> My problem occurs when I try to configure a separate storage >> >> >> network as shown in the blog post. I can get thru the process >> >> >> as outlined, on all three hosts, but the status will not change >> >> >> from "out-of-sync". I can press the "Sync All Networks", and I >> >> >> get a notification which says "Finished SyncAllHostNetworks", >> >> >> but the status of the storage network remains "out-of-sync" . >> >> >> >> >> > >> >> > >> >> > The "Setup Host Networks" dialog presents the information why the >> >> > network is marked as "out-of-sync". >> >> > Does the information presented helps you? >> >> > >> >> >> I don't know if this is related, but I cannot migrate the >> >> >> HostedEngine vm between hosts. >> >> >> >> >> >> I have attached the contents of vdsm.log >> >> >> >> >> >> Any help is appreciated. >> >> > >> > > _______________________________________________ Users mailing list [email protected] http://lists.ovirt.org/mailman/listinfo/users
