On Wed, May 16, 2018 at 3:36 PM, <[email protected]> wrote: > Simone, unfortunately I deleted that install after it failed. > I can re-run the install based on the df -h (see previous post) or I can > change disks & increase the size of /var then re-run the install. > What do you think? > The error I was getting said it could not find the hosted engine at vibr0 > on 192.168.xxx.xx
On my opinion you could simply retry. Please share your log file it fails again. > > > On 2018-05-16 06:30, Simone Tiraboschi wrote: > >> On Wed, May 16, 2018 at 3:25 PM, <[email protected]> wrote: >> >> This is what I had. >>> Does this look correct? >>> >> >> Yes, I think so. >> >> can you please share your hosted-engine-setup log file to understand >> where it's failing? >> >> [root@ovirt-node1 ~]# df -h >>> Filesystem >>> Size Used Avail Use% Mounted on >>> /dev/mapper/onn_ovirt--node1-ovirt--node--ng--4.2.3--0.20180515.0+1 >>> 14G 1.8G 12G 14% / >>> devtmpfs >>> 32G 0 32G 0% /dev >>> tmpfs >>> 32G 8.0K 32G 1% /dev/shm >>> tmpfs >>> 32G 18M 32G 1% /run >>> tmpfs >>> 32G 0 32G 0% /sys/fs/cgroup >>> /dev/sda1 >>> 976M 207M 702M 23% /boot >>> /dev/mapper/onn_ovirt--node1-home >>> 976M 2.6M 907M 1% /home >>> /dev/mapper/onn_ovirt--node1-tmp >>> 976M 2.8M 906M 1% /tmp >>> /dev/mapper/onn_ovirt--node1-var >>> 15G 112M 14G 1% /var >>> /dev/mapper/onn_ovirt--node1-var_log >>> 7.8G 42M 7.3G 1% /var/log >>> /dev/mapper/onn_ovirt--node1-var_log_audit >>> 2.0G 6.3M 1.8G 1% /var/log/audit >>> /dev/mapper/onn_ovirt--node1-var_crash >>> 9.8G 37M 9.2G 1% /var/crash >>> tmpfs >>> 6.3G 0 6.3G 0% /run/user/0 >>> >>> On 2018-05-16 06:14, Simone Tiraboschi wrote: >>> On Wed, May 16, 2018 at 2:52 PM, <[email protected]> wrote: >>> >>> >>> https://www.ovirt.org/documentation/install-guide/chap- >> System_Requirements/ >> >>> [1] >>> [1] says: >>> Important: If you are also installing the oVirt Engine Virtual >>> Appliance for self-hosted engine installation, the /var partition >>> must be at least 60 GB. >>> >>> The appliance disk is shipped as a qcow2 image: 4 GB should be >>> enough. >>> >>> Back to the drawing board, I certainly failed to read that!! >>> >>> On 2018-05-16 02:37, Andrea Dell'Amico wrote: >>> On 16 May 2018, at 09:42, Simone Tiraboschi <[email protected]> >>> wrote: >>> >>> On Tue, May 15, 2018 at 6:31 PM, <[email protected]> wrote: >>> >>> Engine network config error >>> >>> Following this blog post: >>> >>> >>> https://www.ovirt.org/blog/2018/02/up-and-running-with-ovirt >> -4-2-and-gluster-storage/ >> >>> [2] >>> [2] >>> >>> [1] >>> >>> I get an error saying the hosted engine setup is "trying" to use >>> vibr0 (192.168.xxx.x) even though I have the bridge interface set >>> to "eno1" >>> >>> Regardless of whether the Edit Hosts File is checked or unchecked, >>> it overwrites my engine IP entry from 10.50.235.x to 192.168.xxx.x >>> >>> The same thing happens whether I set the engine IP to Static or >>> DHCP (I don't have DNS, I'm using static entries in /etc/hosts). >>> >>> Any ideas it "insists" on using "vibr0" instead of "eno1"? >>> >>> Hi, >>> up to this point is absolutely fine: in the new node zero deployment >>> flow, hosted-engine-setup bootstraps a local VM with an engine there >>> to use that engine to configure the rest of the system (storage, >>> network...). >>> That bootstrap VM runs over default natted libvirt network, that's >>> why you see vibr0 and 192.168.xxx.x at that stage. >>> >>> If you are facing any issue, it's definitively not there. >>> >> >> Yes, the blog post describes the 4.2.{0,1} behaviour while the local >> VM is a change introduced in 4.2.2. >> I faced a similar error and in my case the VM creation failed because >> there was not enough space in /var/tmp. It wasn’t a problem before, >> because the engine VM was created directly on top of a gluster volume. >> >> Andrea >> -- >> Andrea Dell'Amico >> http://adellam. sevenseas.org/ [3] [3] [2] >> >> Links: >> ------ >> [1] >> https://www.ovirt.org/blog/2018/02/up-and-running-with-ovirt >> -4-2-and-gluster-storage/ >> [2] >> [2] >> [2] http://sevenseas.org/ >> _______________________________________________ >> Users mailing list -- [email protected] >> To unsubscribe send an email to [email protected] >> >> Links: >> ------ >> [1] >> https://www.ovirt.org/documentation/install-guide/chap- >> System_Requirements/ >> [1] >> [2] >> https://www.ovirt.org/blog/2018/02/up-and-running-with-ovirt >> -4-2-and-gluster-storage/ >> [2] >> [3] http://sevenseas.org/ >> >> >> >> Links: >> ------ >> [1] https://www.ovirt.org/documentation/install-guide/chap- >> System_Requirements/ >> [2] >> https://www.ovirt.org/blog/2018/02/up-and-running-with-ovirt >> -4-2-and-gluster-storage/ >> [3] http://sevenseas.org/ >> >
_______________________________________________ Users mailing list -- [email protected] To unsubscribe send an email to [email protected]
