On Wed, May 16, 2018 at 3:36 PM, <ov...@fateknollogee.com> wrote:
Simone, unfortunately I deleted that install after it failed.
I can re-run the install based on the df -h (see previous post) or I
can change disks & increase the size of /var then re-run the
install.
What do you think?
The error I was getting said it could not find the hosted engine at
vibr0 on 192.168.xxx.xx
On my opinion you could simply retry.
Please share your log file it fails again.
On 2018-05-16 06:30, Simone Tiraboschi wrote:
On Wed, May 16, 2018 at 3:25 PM, <ov...@fateknollogee.com> wrote:
This is what I had.
Does this look correct?
Yes, I think so.
can you please share your hosted-engine-setup log file to understand
where it's failing?
[root@ovirt-node1 ~]# df -h
Filesystem
Size Used Avail Use% Mounted on
/dev/mapper/onn_ovirt--node1-ovirt--node--ng--4.2.3--0.20180515.0+1
14G 1.8G 12G 14% /
devtmpfs
32G 0 32G 0% /dev
tmpfs
32G 8.0K 32G 1% /dev/shm
tmpfs
32G 18M 32G 1% /run
tmpfs
32G 0 32G 0% /sys/fs/cgroup
/dev/sda1
976M 207M 702M 23% /boot
/dev/mapper/onn_ovirt--node1-home
976M 2.6M 907M 1% /home
/dev/mapper/onn_ovirt--node1-tmp
976M 2.8M 906M 1% /tmp
/dev/mapper/onn_ovirt--node1-var
15G 112M 14G 1% /var
/dev/mapper/onn_ovirt--node1-var_log
7.8G 42M 7.3G 1% /var/log
/dev/mapper/onn_ovirt--node1-var_log_audit
2.0G 6.3M 1.8G 1% /var/log/audit
/dev/mapper/onn_ovirt--node1-var_crash
9.8G 37M 9.2G 1% /var/crash
tmpfs
6.3G 0 6.3G 0% /run/user/0
On 2018-05-16 06:14, Simone Tiraboschi wrote:
On Wed, May 16, 2018 at 2:52 PM, <ov...@fateknollogee.com> wrote:
https://www.ovirt.org/documentation/install-guide/chap-System_Requirements/
[1]
[1]
[1] says:
Important: If you are also installing the oVirt Engine Virtual
Appliance for self-hosted engine installation, the /var partition
must be at least 60 GB.
The appliance disk is shipped as a qcow2 image: 4 GB should be
enough.
Back to the drawing board, I certainly failed to read that!!
On 2018-05-16 02:37, Andrea Dell'Amico wrote:
On 16 May 2018, at 09:42, Simone Tiraboschi <stira...@redhat.com>
wrote:
On Tue, May 15, 2018 at 6:31 PM, <ov...@fateknollogee.com> wrote:
Engine network config error
Following this blog post:
https://www.ovirt.org/blog/2018/02/up-and-running-with-ovirt-4-2-and-gluster-storage/
[2]
[2]
[2]
[1]
I get an error saying the hosted engine setup is "trying" to use
vibr0 (192.168.xxx.x) even though I have the bridge interface set
to "eno1"
Regardless of whether the Edit Hosts File is checked or unchecked,
it overwrites my engine IP entry from 10.50.235.x to 192.168.xxx.x
The same thing happens whether I set the engine IP to Static or
DHCP (I don't have DNS, I'm using static entries in /etc/hosts).
Any ideas it "insists" on using "vibr0" instead of "eno1"?
Hi,
up to this point is absolutely fine: in the new node zero deployment
flow, hosted-engine-setup bootstraps a local VM with an engine there
to use that engine to configure the rest of the system (storage,
network...).
That bootstrap VM runs over default natted libvirt network, that's
why you see vibr0 and 192.168.xxx.x at that stage.
If you are facing any issue, it's definitively not there.
Yes, the blog post describes the 4.2.{0,1} behaviour while the local
VM is a change introduced in 4.2.2.
I faced a similar error and in my case the VM creation failed
because
there was not enough space in /var/tmp. It wasn’t a problem
before,
because the engine VM was created directly on top of a gluster
volume.
Andrea
--
Andrea Dell'Amico
http://adellam. sevenseas.org/ [3] [3] [3] [2]
Links:
------
[1]
https://www.ovirt.org/blog/2018/02/up-and-running-with-ovirt-4-2-and-gluster-storage/
[2]
[2]
[2]
[2] http://sevenseas.org/
_______________________________________________
Users mailing list -- users@ovirt.org
To unsubscribe send an email to users-le...@ovirt.org
Links:
------
[1]
https://www.ovirt.org/documentation/install-guide/chap-System_Requirements/
[1]
[1]
[2]
https://www.ovirt.org/blog/2018/02/up-and-running-with-ovirt-4-2-and-gluster-storage/
[2]
[2]
[3] http://sevenseas.org/
Links:
------
[1]
https://www.ovirt.org/documentation/install-guide/chap-System_Requirements/
[1]
[2]
https://www.ovirt.org/blog/2018/02/up-and-running-with-ovirt-4-2-and-gluster-storage/
[2]
[3] http://sevenseas.org/
Links:
------
[1]
https://www.ovirt.org/documentation/install-guide/chap-System_Requirements/
[2]
https://www.ovirt.org/blog/2018/02/up-and-running-with-ovirt-4-2-and-gluster-storage/
[3] http://sevenseas.org/
_______________________________________________
Users mailing list -- users@ovirt.org
To unsubscribe send an email to users-le...@ovirt.org
