Ran into the same issue with oVirt Node 4.2.7.1 when installing as a virtual guest. Didi, Can you point us in the right direction?
Thanks On Mon, Dec 10, 2018 at 2:23 AM Vincent Royer <vinc...@epicenergy.ca> wrote: > > This happened to me too. > > The NIC doesn't come "up" on the first boot, even though it was initiated > during the setup. DHCP or static makes no difference to this situation. iirc > I used nmtui to bring the interface up and verify the hostname. Can't do it > in cockpit without the interface being up... > > Once you're in the engine you can initialize and add the rest of the required > nics. > > I'm not sure if this is as designed or a bug, but it last happened to me on > 4.2.5, and was the same process on my 3 hosts. > > > On Sun, Dec 9, 2018 at 12:14 AM Eitan Raviv <era...@redhat.com> wrote: >> >> On Thu, Dec 6, 2018 at 7:10 PM Stefan Wolf <shb...@gmail.com> wrote: >> > >> > Hello, >> > >> > >> > >> > I ve downloaded an installed OVIRT NODE 4.2.7.1. >> > >> > During the installation I ‘ve setup a static ip (I ‘ve also tried dhcp, >> > both work) >> > >> >> how did you setup the static ip? did you use Cockpit? >> >> >> > The installation passes and after the reboot ovirt node starts without any >> > problems. >> > >> > BUT the network is not configured. >> >> what do you mean by 'network is not configured'? the static IP is not >> assigned to your selected NIC or sth else? >> >> >> > >> > I know https://www.ovirt.org/documentation/install-guide/chap-oVirt_Nodes/ >> > and I know >> > >> > https://www.ovirt.org/documentation/admin-guide/chap-Hosts/ >> > >> > >> > >> > and now I am between these two documents >> > >> > oVirt is installed but network is not configured to add it to datacenter >> > >> > >> > >> > of course I know the scripts under /etc/sysconfig/network-scripts >> > >> > do I really have do edit it manuel? >> > >> > >> > >> > if I change ip in command line >> > >> > ip a add … dev.. >> > >> > and ip route add … >> > >> > it fails to add node to datacenter >> > >> > >> > >> > - with one of the last version I ‘ve added the IP address in bash >> > >> > - added the host to datacenter, >> > >> > - after reboot readd the ip address in bash after reboot >> > >> > - an then I could change network settings in oVirt Manger >> > >> > >> > >> > What is best practices for adding a node to datacenter when the ip address >> > is not assigned after installation >> > >> > >> > >> > Thx shb >> > >> > _______________________________________________ >> > Users mailing list -- users@ovirt.org >> > To unsubscribe send an email to users-le...@ovirt.org >> > Privacy Statement: https://www.ovirt.org/site/privacy-policy/ >> > oVirt Code of Conduct: >> > https://www.ovirt.org/community/about/community-guidelines/ >> > List Archives: >> > https://lists.ovirt.org/archives/list/users@ovirt.org/message/TH5MRXJUU4SI62Z5XXQX2S6GKBOQIJWW/ >> _______________________________________________ >> Users mailing list -- users@ovirt.org >> To unsubscribe send an email to users-le...@ovirt.org >> Privacy Statement: https://www.ovirt.org/site/privacy-policy/ >> oVirt Code of Conduct: >> https://www.ovirt.org/community/about/community-guidelines/ >> List Archives: >> https://lists.ovirt.org/archives/list/users@ovirt.org/message/PULDN5JRT6PZYVCPHQDIRVLVKIASXNAT/ _______________________________________________ Users mailing list -- users@ovirt.org To unsubscribe send an email to users-le...@ovirt.org Privacy Statement: https://www.ovirt.org/site/privacy-policy/ oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/ List Archives: https://lists.ovirt.org/archives/list/users@ovirt.org/message/JU7CNSWWKVEQBX44BSGTEFD6UMJMEZSS/
