Hi Chuck,
thanks for the advice. Sadly, though, this doesn't seem to have any (positive)
impact, i.e. using the config below, we still only get max 2500 msg/sec
throughput.
[
["router", {
"id": "Hono.Example.Router",
"mode": "standalone",
"workerThreads": 4
}],
["listener", {
"host": "0.0.0.0",
"port": 5672,
"authenticatePeer": "no",
"linkCapacity": 1000
}],
["address", {
"prefix": "telemetry/",
"distribution": "balanced"
}],
["policy", {
"maxConnections": 1000,
"enableVhostPolicy": true
}],
["vhost", {
"id": "$default",
"maxConnections": 100,
"allowUnknownUser": true,
"groups": {
"$default": {
"remoteHosts": "*",
"maxSessions": 500,
"maxMessageSize": 204800,
"allowUserIdProxy": true,
"sources": "*",
"targets": "*"
}
}
}],
["log", {
"module": "DEFAULT",
"enable": "info+"
}]
]
Any thoughts?
Mit freundlichen Grüßen / Best regards
Kai Hudalla
Chief Software Architect
Bosch Software Innovations GmbH
Schöneberger Ufer 89-91
10785 Berlin
GERMANY
www.bosch-si.com
Registered office: Berlin, Register court: Amtsgericht Charlottenburg, HRB
148411 B;
Executives: Dr.-Ing. Rainer Kallenbach, Michael Hahn
________________________________________
From: Chuck Rolke <[email protected]>
Sent: Tuesday, July 18, 2017 20:40
To: [email protected]
Subject: Re: Dispatch Router throughput
In the hono vhost policy section try adding:
"allowUserIdProxy": true
If the user id proxy setting is false then the router must parse every
message through to the user-id field of the message properties. Then
verify that the user has no name in the message user-id or the
same name that was used when the connection was created.
Allowing the user id proxy bypasses the per-message parsing and checking.
The down side of setting the user id proxy to true is it allows
the user to launch messages into the system with any user-id.
Per-message checks are avoided altogether when the messages arrive
over a 'link routed' path. That should give you even better numbers.
-Chuck
----- Original Message -----
> From: "Hudalla Kai (INST/ECS4)" <[email protected]>
> To: [email protected]
> Sent: Tuesday, July 18, 2017 11:21:40 AM
> Subject: Re: Dispatch Router throughput
>
> Hi,
>
> I think we have narrowed it down.
>
> Running the quiver test as suggested by Gordon (thanks for that :-)) and
> using the Dispatch Router config below, we get around 30000 msg/sec if we
> set "enableVhostPolicy" to false and around 2500 msgs/sec when we set it to
> "true".
>
> [
> ["router", {
> "id": "Hono.Example.Router",
> "mode": "standalone",
> "workerThreads": 4
> }],
>
> ["listener", {
> "host": "0.0.0.0",
> "port": 5672,
> "authenticatePeer": false,
> "linkCapacity": 1000
> }],
>
> ["policy", {
> "enableVhostPolicy": false,
> "defaultVhost": "hono"
> }],
>
> ["vhost", {
> "id": "hono",
> "allowUnknownUser": true,
> "groups": {
> "$default": {
> "remoteHosts": "*",
> "sources": "*",
> "targets": "*"
> }
> }
> }],
>
> ["log", {
> "module": "DEFAULT",
> "enable": "info+"
> }]
> ]
>
> We are running the test against the enmasseproject/qdrouterd-base:0.8.0-1
> Docker image.
> Is this the expected behavior?
>
> Mit freundlichen Grüßen / Best regards
>
> Kai Hudalla
> Chief Software Architect
>
> Bosch Software Innovations GmbH
> Schöneberger Ufer 89-91
> 10785 Berlin
> GERMANY
> www.bosch-si.com
>
> Registered office: Berlin, Register court: Amtsgericht Charlottenburg, HRB
> 148411 B;
> Executives: Dr.-Ing. Rainer Kallenbach, Michael Hahn
>
> ________________________________________
> From: Gordon Sim <[email protected]>
> Sent: Tuesday, July 18, 2017 14:05
> To: [email protected]
> Subject: Re: Dispatch Router throughput
>
> On 18/07/17 11:53, Hudalla Kai (INST/ECS4) wrote:
> > We are running Dispatch Router by means of the
> > enmasseproject/qdrouterd-base:0.8.0-1 Docker image. Do you have any
> > concerns regarding a negative impact this might have on throughput?
>
> Using that image (default config) with qpid-send/qpid-receive from
> qpid::messaging, I see >90k msgs/sec, so I don't think it is the image.
>
> Using the vertx-proton option for Justin Ross's quiver benchmark[1]
> against that same image I get ~39k msgs/sec.
>
> [1] https://github.com/ssorj/quiver/
>
> ---------------------------------------------------------------------
> To unsubscribe, e-mail: [email protected]
> For additional commands, e-mail: [email protected]
>
>
> ---------------------------------------------------------------------
> To unsubscribe, e-mail: [email protected]
> For additional commands, e-mail: [email protected]
>
>
---------------------------------------------------------------------
To unsubscribe, e-mail: [email protected]
For additional commands, e-mail: [email protected]
---------------------------------------------------------------------
To unsubscribe, e-mail: [email protected]
For additional commands, e-mail: [email protected]
