Solved, One of the main changes I had made (apart from installing other software) was to change the root RW partition from 8mb to 15mb.
I had made the same change on an older version without any trouble, Punky is there any reason it causes a failure now and is it still possible to change it? Thanks Wayne > -----Original Message----- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] > On Behalf Of Wayne Lee > Sent: 14 April 2008 10:26 > To: [EMAIL PROTECTED] > Subject: [Voyage-linux] mounting local file systems failed > > Hi Guys > > > I'm playing with a new install of voyage 0.4.1, when mounting the > filesystems during boot it is failing, it then continues to load the OS > fine and it can remount the drives RW and Ro at the last stages of > boot. > > Below is the boot process and marked the mount processes with *****. > > > Thanks > > > Wayne > > > [Linux-initrd @ 0xfe10000, 0x1df28f bytes] > > [6nLinux version 2.6.20-486-voyage ([EMAIL PROTECTED]) (gcc version > 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 PREEMPT Mon Jul 16 > 06:39:47 GMT 2007 () > BIOS-provided physical RAM map: > sanitize start > sanitize end > copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: > 000000000009fc00 type: 1 > copy_e820_map() type is E820_RAM > copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: > 00000000000a0000 type: 2 > copy_e820_map() start: 00000000000f0000 size: 0000000000010000 end: > 0000000000100000 type: 2 > copy_e820_map() start: 0000000000100000 size: 000000000ff00000 end: > 0000000010000000 type: 1 > copy_e820_map() type is E820_RAM > copy_e820_map() start: 00000000fff00000 size: 0000000000100000 end: > 0000000100000000 type: 2 > BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) > BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) > BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) > BIOS-e820: 0000000000100000 - 0000000010000000 (usable) > BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) > 256MB LOWMEM available. > Zone PFN ranges: > DMA 0 -> 4096 > Normal 4096 -> 65536 > early_node_map[1] active PFN ranges > 0: 0 -> 65536 > DMI not present or invalid. > Allocating PCI resources starting at 20000000 (gap: 10000000:eff00000) > Detected 266.668 MHz processor. > Built 1 zonelists. Total pages: 65024 > Kernel command line: root=/dev/hdb1 console=ttyS0,9600n8 > No local APIC present or hardware disabled > Initializing CPU#0 > PID hash table entries: 1024 (order: 10, 4096 bytes) > Console: colour dummy device 80x25 > Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) > Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) > Memory: 254652k/262144k available (1610k kernel code, 6936k reserved, > 562k data, 148k init, 0k highmem) > virtual kernel memory layout: > fixmap : 0xfffbb000 - 0xfffff000 ( 272 kB) > vmalloc : 0xd0800000 - 0xfffb9000 ( 759 MB) > lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) > .init : 0xc0322000 - 0xc0347000 ( 148 kB) > .data : 0xc029297e - 0xc031f1ac ( 562 kB) > .text : 0xc0100000 - 0xc029297e (1610 kB) > Checking if this processor honours the WP bit even in supervisor > mode... Ok. > Calibrating delay using timer specific routine.. 533.84 BogoMIPS > (lpj=266924) > Mount-cache hash table entries: 512 > Compat vDSO mapped to ffffe000. > Remapping vsyscall page to ffffe000 > CPU: NSC Unknown stepping 01 > Checking 'hlt' instruction... OK. > NET: Registered protocol family 16 > PCI: PCI BIOS revision 2.01 entry at 0xf7861, last bus=1 > PCI: Using configuration type 1 > Setting up standard PCI resources > PCI: Probing PCI hardware > PCI: Bridge: 0000:00:0a.0 > IO window: d000-dfff > MEM window: a4000000-a7ffffff > PREFETCH window: 20000000-200fffff > NET: Registered protocol family 2 > IP route cache hash table entries: 2048 (order: 1, 8192 bytes) > TCP established hash table entries: 8192 (order: 3, 32768 bytes) > TCP bind hash table entries: 4096 (order: 2, 16384 bytes) > TCP: Hash tables configured (established 8192 bind 4096) > TCP reno registered > checking if image is initramfs... it is > Freeing initrd memory: 1916k freed > geode-mfgpt: Not a Geode GX/LX processor > io scheduler noop registered > io scheduler cfq registered (default) > Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing > enabled > ÿserial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A > mice: PS/2 mouse device common for all mice > RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize > Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 > ide: Assuming 33MHz system bus speed for PIO modes; override with > idebus=xx > SC1200: IDE controller at PCI slot 0000:00:12.2 > SC1200: chipset revision 1 > SC1200: not 100% native mode: will probe irqs later > ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:pio, hdb:pio > ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:pio, hdd:pio > hdb: CF CARD 1GB, ATA DISK drive > hdb: sc1200_set_xfer_mode(MW DMA 2) > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 > hdb: max request size: 128KiB > hdb: 1981728 sectors (1014 MB) w/1KiB Cache, CHS=1966/16/63, DMA > hdb: hdb1 > i8042.c: Can't read CTR while initializing i8042. > i8042: probe of i8042 failed with error -5 > padlock: No VIA PadLock drivers have been loaded. > padlock: VIA PadLock not detected. > padlock: VIA PadLock Hash Engine not detected. > TCP cubic registered > NET: Registered protocol family 1 > NET: Registered protocol family 17 > Using IPI Shortcut mode > Time: tsc clocksource has been installed. > Freeing unused kernel memory: 148k freed > Loading, please wait... > Begin: Loading essential drivers... ... > Done. > Begin: Running /scripts/init-premount ... > natsemi dp8381x driver, version 2.1, Sept 11, 2006 > originally by Donald Becker <[EMAIL PROTECTED]> > http://www.scyld.com/network/natsemi.html > 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder > natsemi eth0: NatSemi DP8381[56] at 0xa0000000 (0000:00:06.0), > 00:00:24:c9:49:a4, IRQ 10, port TP. > natsemi eth1: NatSemi DP8381[56] at 0xa0001000 (0000:00:07.0), > 00:00:24:c9:49:a5, IRQ 10, port TP. > natsemi eth2: NatSemi DP8381[56] at 0xa0002000 (0000:00:08.0), > 00:00:24:c9:49:a6, IRQ 10, port TP. > natsemi eth3: NatSemi DP8381[56] at 0xa4000000 (0000:01:00.0), > 00:00:24:c8:2d:18, IRQ 5, port TP. > natsemi eth4: NatSemi DP8381[56] at 0xa4001000 (0000:01:01.0), > 00:00:24:c8:2d:19, IRQ 11, port TP. > usbcore: registered new interface driver usbfs > usbcore: registered new interface driver hub > usbcore: registered new device driver usb > ohci_hcd 0000:00:13.0: OHCI Host Controller > ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1 > ohci_hcd 0000:00:13.0: irq 11, io mem 0xa0003000 > usb usb1: configuration #1 chosen from 1 choice > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 3 ports detected > Done. > Begin: Mounting root file system... ... > Begin: Running /scripts/local-top ... > Done. > Begin: Running /scripts/local-premount ... > Done. > Begin: Running /scripts/local-bottom ... > Done. > Done. > Begin: Running /scripts/init-bottom ... > Done. > > INIT: version 2.86 booting > > hostname: the specified hostname is invalid > Starting the hotplug events dispatcher: udevd. > Synthesizing the initial hotplug events...done. > Waiting for /dev to be fully populated...scx200: NatSemi SCx200 Driver > scx200: GPIO base 0x6100 > scx200: Configuration Block base 0x6000 > done. > Activating swap...done. > /etc/rcS.d/S11hwclock.sh: line 51: /etc/adjtime: No such file or > directory > Setting the system clock.. > Cleaning up ifupdown.... > Loading kernel modules...hostap_pci: 0.4.4-kernel (Jouni Malinen > <[EMAIL PROTECTED]>) > done. > Loading device-mapper supportdevice-mapper: ioctl: 4.11.0-ioctl (2006- > 10-12) initialised: [EMAIL PROTECTED] > TSC appears to be running slowly. Marking it as unstable > Time: pit clocksource has been installed. > . > Checking file systems...fsck 1.40-WIP (14-Nov-2006) > done. > Setting kernel variables...done. > ***** Mounting local filesystems...[31mfailed.[39;49m ***** > Activating swapfile swap...done. > Setting up networking.... > Configuring network interfaces...eth0: DSPCFG accepted after 0 usec. > eth1: DSPCFG accepted after 0 usec. > NET: Registered protocol family 10 > lo: Disabled Privacy Extensions > ADDRCONF(NETDEV_UP): eth0: link is not ready > ADDRCONF(NETDEV_UP): eth1: link is not ready > Mobile IPv6 > eth2: DSPCFG accepted after 0 usec. > ADDRCONF(NETDEV_UP): eth2: link is not ready > eth3: DSPCFG accepted after 0 usec. > ADDRCONF(NETDEV_UP): eth3: link is not ready > eth4: DSPCFG accepted after 0 usec. > ADDRCONF(NETDEV_UP): eth4: link is not ready > done. > Starting "Shorewall firewall": not done (check /var/log/shorewall- > init.log). > Starting portmap daemon.... > > INIT: Entering runlevel: 2 > > Starting system log daemon: syslogd. > Starting kernel log daemon: klogd. > Starting DNS forwarder and DHCP server: dnsmasq. > Starting portmap daemon...Already running.. > Starting advanced IEEE 802.11 management: disabled via > /etc/default/hostapd. > nocatsplash daemon disabled - read /etc/default/nocatsplash. > [33m*[39;49m Not starting internet superserver: no services enabled. > Starting PPTP Daemon: pptpd. > Starting network management services: snmpd. > Starting OpenBSD Secure Shell server: sshd. > Starting periodic command scheduler: crond. > Starting watchdog daemon: watchdog. > ***** Remounting / as read-write ... Done. ***** > ***** Removing /etc/nologin ... Done. ***** > ***** Remounting / as read-only ... Done. ***** > > Debian GNU/Linux 4.0 MAN-D&D ttyS0 > > MAN-D&D login: > > > _______________________________________________ > Voyage-linux mailing list > [email protected] > http://list.voyage.hk/mailman/listinfo/voyage-linux _______________________________________________ Voyage-linux mailing list [email protected] http://list.voyage.hk/mailman/listinfo/voyage-linux
