Hey Punky, Am 08.02.2015 um 15:03 schrieb Punky Tse: >> yesterday I got my brandnew Raspberry 2 B board and immediately tried >> Voyage MuBox with it. But I can't fire it up. The kernel locks upon >> bootup. >> > Let me reinstall a to a new uSD card tomorrow and revert to you. > > I first installed for my RPi B+, update the kernel/firmware by > rpi-update, then put the uSD card to RPi 2B and it works perfectly. > https://plus.google.com/107906919028234849442/posts/SiNtFywY6Fj
Okay, that sounds as if there are fewer problems, than I thought. I just downloaded the install script from: http://mirror.voyage.hk/download/voyage-mubox/rpi/install-mubox-rpi.sh Then I ran as root with a 32GB Samsung Micro-SD-Card as /dev/sdf in my desktop: # sh /tmp/install-mubox-rpi.sh /dev/sdf Here's the output from the isntall (just ran it again): # sh /tmp/install-mubox-rpi.sh /dev/sdf 1+0 Datensätze ein 1+0 Datensätze aus 512 Bytes (512 B) kopiert, 0,00114581 s, 447 kB/s Device contains neither a valid DOS partition table, nor Sun, SGI or OSF disklabel Building a new DOS disklabel with disk identifier 0x232b760e. Changes will remain in memory only, until you decide to write them. After that, of course, the previous content won't be recoverable. Warning: invalid flag 0x0000 of partition table 4 will be corrected by w(rite) Command (m for help): Building a new DOS disklabel with disk identifier 0x80c7d365. Changes will remain in memory only, until you decide to write them. After that, of course, the previous content won't be recoverable. Warning: invalid flag 0x0000 of partition table 4 will be corrected by w(rite) Command (m for help): Partition type: p primary (0 primary, 0 extended, 4 free) e extended Select (default p): Partition number (1-4, default 1): First sector (2048-61407231, default 2048): Using default value 2048 Last sector, +sectors or +size{K,M,G} (2048-61407231, default 61407231): Command (m for help): Selected partition 1 Hex code (type L to list codes): Changed system type of partition 1 to c (W95 FAT32 (LBA)) Command (m for help): Partition type: p primary (1 primary, 0 extended, 3 free) e extended Select (default p): Partition number (1-4, default 2): First sector (133120-61407231, default 133120): Using default value 133120 Last sector, +sectors or +size{K,M,G} (133120-61407231, default 61407231): Using default value 61407231 Command (m for help): The partition table has been altered! Calling ioctl() to re-read partition table. WARNING: Re-reading the partition table failed with error 16: Das Gerät oder die Ressource ist belegt. The kernel still uses the old table. The new table will be used at the next reboot or after you run partprobe(8) or kpartx(8) WARNING: If you have created or modified any DOS 6.x partitions, please see the fdisk manual page for additional information. Syncing disks. mkfs.vfat 3.0.13 (30 Jun 2012) mke2fs 1.42.5 (29-Jul-2012) mkfs.ext4: Inodegröße (128) * Anzahl_Inodes (0) ist zu gross für ein Dateisystem mit 0 Blöcken, geben Sie bitte entweder ein höheres Inodeverhältnis (-i) oder eine niedrigere Anzahl an Inodes (-N) an. tune2fs 1.42.5 (29-Jul-2012) tune2fs: Ein Block konnte nicht in einem Zug gelesen werden beim Versuch, /dev/sdf2 zu öffnen Kann keinen gültigen Dateisystem-Superblock finden. Disk /dev/sdf: 31.4 GB, 31440502784 bytes 64 heads, 32 sectors/track, 29984 cylinders, total 61407232 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x80c7d365 Device Boot Start End Blocks Id System /dev/sdf1 2048 133119 65536 c W95 FAT32 (LBA) /dev/sdf2 133120 61407231 30637056 83 Linux mount: you must specify the filesystem type % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 42.1M 100 42.1M 0 0 374k 0 0:01:55 0:01:55 --:--:-- 398k umount: /tmp/cf: not mounted mount: you must specify the filesystem type % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 168 0 168 0 0 281 0 --:--:-- --:--:-- --:--:-- 388 100 43.2M 100 43.2M 0 0 16872 0 0:44:47 0:44:47 --:--:-- 22455 umount: /tmp/cf: not mounted mount: you must specify the filesystem type *** depmod 3.18.6-v7+ *** depmod 3.18.6+ % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 0 0 0 0 0 0 0 0 --:--:-- --:--:-- --:--:-- 0 100 7938 100 7938 0 0 10129 0 --:--:-- --:--:-- --:--:-- 10129 mkdir: kann Verzeichnis „/tmp/cf/boot.bak“ nicht anlegen: Die Datei existiert bereits mv: Verschieben von „/tmp/cf/boot/modules“ nach „/tmp/cf/boot.bak/modules“ nicht möglich: Das Verzeichnis ist nicht leer mv: Verschieben von „/tmp/cf/boot/overlays“ nach „/tmp/cf/boot.bak/overlays“ nicht möglich: Das Verzeichnis ist nicht leer mv: Verschieben von „/tmp/cf/boot/vc“ nach „/tmp/cf/boot.bak/vc“ nicht möglich: Das Verzeichnis ist nicht leer umount: /tmp/cf: not mounted Voyage MuBox for RaspBerry Pi installed! ... this ran obiusly into trouble, again. Obviously something went wrong with the partitioning. The kernel halts after 3.5 seconds and says: Kernel panic - not syncing: VFS: Unable to mount root-fs on unknown block(179,2) Could this possibly stem from Locale-Settings? I just tried the following: # LANG=C; LANGUAGE=C; LC_ALL=C # sh /tmp/install-mubox-rpi.sh /dev/sdf 1+0 records in 1+0 records out 512 bytes (512 B) copied, 5.2387e-05 s, 9.8 MB/s Device contains neither a valid DOS partition table, nor Sun, SGI or OSF disklabel Building a new DOS disklabel with disk identifier 0xa6a4d70b. Changes will remain in memory only, until you decide to write them. After that, of course, the previous content won't be recoverable. Warning: invalid flag 0x0000 of partition table 4 will be corrected by w(rite) Command (m for help): Building a new DOS disklabel with disk identifier 0x32a3a898. Changes will remain in memory only, until you decide to write them. After that, of course, the previous content won't be recoverable. Warning: invalid flag 0x0000 of partition table 4 will be corrected by w(rite) Command (m for help): Partition type: p primary (0 primary, 0 extended, 4 free) e extended Select (default p): Partition number (1-4, default 1): First sector (2048-61407231, default 2048): Using default value 2048 Last sector, +sectors or +size{K,M,G} (2048-61407231, default 61407231): Command (m for help): Selected partition 1 Hex code (type L to list codes): Changed system type of partition 1 to c (W95 FAT32 (LBA)) Command (m for help): Partition type: p primary (1 primary, 0 extended, 3 free) e extended Select (default p): Partition number (1-4, default 2): First sector (133120-61407231, default 133120): Using default value 133120 Last sector, +sectors or +size{K,M,G} (133120-61407231, default 61407231): Using default value 61407231 Command (m for help): The partition table has been altered! Calling ioctl() to re-read partition table. WARNING: Re-reading the partition table failed with error 16: Device or resource busy. The kernel still uses the old table. The new table will be used at the next reboot or after you run partprobe(8) or kpartx(8) WARNING: If you have created or modified any DOS 6.x partitions, please see the fdisk manual page for additional information. Syncing disks. mkfs.vfat 3.0.13 (30 Jun 2012) mkfs.vfat: /dev/sdf1 contains a mounted file system. mke2fs 1.42.5 (29-Jul-2012) Filesystem label= OS type: Linux Block size=4096 (log=2) Fragment size=4096 (log=2) Stride=0 blocks, Stripe width=0 blocks 1916928 inodes, 7659264 blocks 382963 blocks (5.00%) reserved for the super user First data block=0 Maximum filesystem blocks=4294967296 234 block groups 32768 blocks per group, 32768 fragments per group 8192 inodes per group Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208, 4096000 Allocating group tables: done Writing inode tables: done Creating journal (32768 blocks): done Writing superblocks and filesystem accounting information: done tune2fs 1.42.5 (29-Jul-2012) Setting maximal mount count to -1 Setting interval between checks to 0 seconds Disk /dev/sdf: 31.4 GB, 31440502784 bytes 64 heads, 32 sectors/track, 29984 cylinders, total 61407232 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x32a3a898 Device Boot Start End Blocks Id System /dev/sdf1 2048 133119 65536 c W95 FAT32 (LBA) /dev/sdf2 133120 61407231 30637056 83 Linux % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 42.1M 100 42.1M 0 0 453k 0 0:01:35 0:01:35 --:--:-- 284k % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 168 0 168 0 0 294 0 --:--:-- --:--:-- --:--:-- 417 100 43.2M 100 43.2M 0 0 2026k 0 0:00:21 0:00:21 --:--:-- 2680k *** depmod 3.18.6-v7+ *** depmod 3.18.6+ % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 0 0 0 0 0 0 0 0 --:--:-- --:--:-- --:--:-- 0 100 7938 100 7938 0 0 7026 0 0:00:01 0:00:01 --:--:-- 7026 Voyage MuBox for RaspBerry Pi installed! Now it fires up. - Cool! ... Maybe it's a good idea to integrate the Language-Settings into the script? ... can't await to get my Hifiberry DAC+ getting processed by customs, then I'll have a cool and low-cost Media-Player and Web-Radio. By the way: Has anybody already toyed around with the Displays for the Raspberry Pi? Being able to browse through the playlists albums and stuff as with other mpd-clients with a remote would be really cool. CU Stefan. -- Stefan U. Hegner <ste...@teleos-web.de> * * * D-32584 Löhne --- good ole Germany
_______________________________________________ Voyage-linux mailing list Voyage-linux@list.voyage.hk http://list.voyage.hk/mailman/listinfo/voyage-linux
