shouldn't be hard https://wiki.ubuntu.com/SystemdForUpstartUsers
On Monday, February 8, 2016 at 5:02:33 PM UTC+1, Jim S wrote: > > I played with this a bit over the weekend but was unable to get it working > on Ubuntu 15.x. > > My production servers all run 14.4. > > I think the problem is the change from upstart to systemd on Ubuntu. Does > anyone have experience getting uwsgi to start using systemd? I don't know > enough about these systems to get it all right. I think it involves have a > uwsgi.service file defined so that systemd will start it up, but I don't > know for sure how to get that all working. > > -Jim > > > On Saturday, February 6, 2016 at 10:20:31 AM UTC-6, xmarx wrote: >> >> >> selman@selman-VirtualBox:~$ ps -ewwf | grep uwsgi >> selman 1878 1848 0 18:15 pts/2 00:00:00 grep --color=auto uwsgi >> selman@selman-VirtualBox:~$ sudo restart uwsgi-emperor >> [sudo] password for selman: >> restart: Upstart'a bağlanılamıyor: Failed to connect to socket >> /com/ubuntu/upstart: Bağlantı reddedildi >> >> >> english: could't connect upstart. Failed to connect to socket >> /com/ubuntu/upstart: connection denied. >> >> >> >> >> >> 6 Şubat 2016 Cumartesi 00:46:28 UTC+2 tarihinde Jim S yazdı: >>> >>> Also, what happens when you run: >>> >>> sudo restart uwsgi-emperor >>> >>> >>> You should get something like this: >>> >>> >>> uwsgi-emperor start/running, process 2749 >>> >>> >>> -Jim >>> >>> >>> >>> On Friday, February 5, 2016 at 4:34:54 PM UTC-6, Jim S wrote: >>>> >>>> Do you know if uwsgi is running: >>>> >>>> Try this from the command line... >>>> >>>> ps -ewwf | grep uwsgi >>>> >>>> results should look something like this: >>>> >>>> [image: Inline image 1] >>>> >>>> -Jim >>>> >>>> >>>> >>>> On Fri, Feb 5, 2016 at 3:18 PM, xmarx <[email protected]> wrote: >>>> >>>>> ubuntu 15.10 is running on vm VirtualBox. >>>>> i exec the script and didn't install anything. nginx is installed by >>>>> the script and running. >>>>> http://localhost/ and https://localhost/ raise 502 Bad Gateway page. >>>>> >>>>> there isn't a routes.py file in /home/www-data/web2py/ >>>>> web2py file is attached in /etc/nginx/sites-available/ >>>>> >>>>> my script is: >>>>> https://raw.githubusercontent.com/web2py/web2py/master/scripts/setup-web2py-nginx-uwsgi-ubuntu.sh >>>>> >>>>> thanks for your help Jim. >>>>> >>>>> >>>>> >>>>> 5 Şubat 2016 Cuma 21:56:00 UTC+2 tarihinde Jim S yazdı: >>>>>> >>>>>> Did you install nginx after running the script? nginx is >>>>>> automatically installed by the script, you don't have to do it manually. >>>>>> >>>>>> If you didn't do that (I could be reading your message wrong), can >>>>>> you post the following files? >>>>>> >>>>>> /home/www-data/web2py/routes.py >>>>>> /etc/nginx/sites-available/web2py >>>>>> >>>>>> They will tell us a bit about how it is behaving. >>>>>> >>>>>> -Jim >>>>>> >>>>>> >>>>>> On Friday, February 5, 2016 at 1:28:10 PM UTC-6, xmarx wrote: >>>>>>> >>>>>>> i read the deployment recipes page and nginx section again and >>>>>>> again. i don`t see about `after install` >>>>>>> >>>>>>> i try install this script >>>>>>> http://web2py.googlecode.com/hg/scripts/setup-web2py-ubuntu.sh >>>>>>> after your message. when installing done. i type localhost on my >>>>>>> browser. >>>>>>> then i get web2py welcome page. but when i install nginx\ localhost is >>>>>>> nginx`s welcome page. >>>>>>> >>>>>>> thanks. >>>>>>> >>>>>>> 5 Şubat 2016 Cuma 17:54:39 UTC tarihinde Jim S yazdı: >>>>>>>> >>>>>>>> Actually, this is the link you want: >>>>>>>> >>>>>>>> >>>>>>>> http://web2py.com/books/default/chapter/29/13/deployment-recipes#Nginx >>>>>>>> >>>>>>>> Also, notice that there are automatic install scripts at the end of >>>>>>>> this section for ubuntu and nginx. >>>>>>>> >>>>>>>> Assuming you're in production, you don't 'have' to run under nginx, >>>>>>>> it is just recommended. >>>>>>>> >>>>>>>> Once this is setup, web2py will be running through nginx and uwsgi, >>>>>>>> no need to 'start' it with the web2py.py pgm. >>>>>>>> >>>>>>>> If you read through the docs it is explained pretty well. >>>>>>>> >>>>>>>> -Jim >>>>>>>> >>>>>>>> >>>>>>>> On Friday, February 5, 2016 at 11:52:16 AM UTC-6, Jim S wrote: >>>>>>>>> >>>>>>>>> Have you read through this? >>>>>>>>> >>>>>>>>> >>>>>>>>> http://web2py.com/books/default/chapter/29/13/deployment-recipes#Linux-and-Unix >>>>>>>>> >>>>>>>>> -Jim >>>>>>>>> >>>>>>>>> On Friday, February 5, 2016 at 11:33:57 AM UTC-6, xmarx wrote: >>>>>>>>>> >>>>>>>>>> i install on ubuntu web2py, nginx and uwsgi. >>>>>>>>>> >>>>>>>>>> when i run web2py (sudo python web2py.py) admin says Running on >>>>>>>>>> Rocket 1.2.6, Python 2.7.10. >>>>>>>>>> >>>>>>>>>> where did i mistake? it must run on nginx, am i right? >>>>>>>>>> >>>>>>>>>> thanks. >>>>>>>>>> >>>>>>>>> -- >>>>> Resources: >>>>> - http://web2py.com >>>>> - http://web2py.com/book (Documentation) >>>>> - http://github.com/web2py/web2py (Source code) >>>>> - https://code.google.com/p/web2py/issues/list (Report Issues) >>>>> --- >>>>> You received this message because you are subscribed to a topic in the >>>>> Google Groups "web2py-users" group. >>>>> To unsubscribe from this topic, visit >>>>> https://groups.google.com/d/topic/web2py/ZM9IIEjtHSI/unsubscribe. >>>>> To unsubscribe from this group and all its topics, send an email to >>>>> [email protected]. >>>>> For more options, visit https://groups.google.com/d/optout. >>>>> >>>> >>>> -- Resources: - http://web2py.com - http://web2py.com/book (Documentation) - http://github.com/web2py/web2py (Source code) - https://code.google.com/p/web2py/issues/list (Report Issues) --- You received this message because you are subscribed to the Google Groups "web2py-users" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
