I have no explanation for why there are multiple log entries for some events. It must be something about the logging system on your operating system.
Your friend's Vantage station is using a very long archive interval of 30 minutes. It's quite possible that everything is fine --- you just haven't waited long enough. You could try a shorter archive interval, say 5 minutes: wee_device --set-interval=5 -tk On Sat, May 6, 2017 at 11:52 AM, <[email protected]> wrote: > A lot of thank’s. > > > > Here you have. > > > > Using configuration file /etc/weewx/weewx.conf > > Using database binding 'wx_binding', which is bound to database > 'archive_sqlite' > > > > System info > > CPU implementer: 0x41 > > Features: half thumb fastmult vfp edsp neon vfpv3 tls > vfpv4 idiva idivt vfpd32 lpae evtstrm > > CPU architecture: 7 > > BogoMIPS: 38.40 > > Hardware: BCM2709 > > CPU revision: 5 > > CPU part: 0xc07 > > model name: ARMv7 Processor rev 5 (v7l) > > Serial: 0000000081eaa714 > > processor: 3 > > CPU variant: 0x0 > > Revision: a01041 > > > > Operating system: debian 8.0 > > Linux ea5by-meteo 4.1.17-v7+ #838 SMP Tue Feb 9 > 13:15:09 GMT 2016 armv7l > > 1 minute load average: 0.01 > > 5 minute load average: 0.14 > > 15 minute load average: 0.38 > > > > General weewx info > > Weewx version 3.7.1 detected. > > > > Station info > > Station type: Vantage > > Driver: weewx.drivers.vantage > > > > Driver info > > [Vantage] > > # This section is for a Davis VantagePro2, VantageVue or WeatherLinkIP > > > > # Connection type: serial or ethernet > > # serial (the classic VantagePro) > > # ethernet (the WeatherLinkIP) > > type = serial > > > > # If the connection type is serial, a port must be specified: > > # Debian, Ubuntu, Redhat, Fedora, and SuSE: > > # /dev/ttyUSB0 is a common USB port name > > # /dev/ttyS0 is a common serial port name > > # BSD: > > # /dev/cuaU0 is a common serial port name > > port = /dev/ttyUSB0 > > # port = /dev/ttyUSB0 > > > > # If the connection type is ethernet, an IP Address/hostname is > required: > > host = 1.2.3.4 > > > > ###################################################### > > # The rest of this section rarely needs any attention. > > # You can safely leave it "as is." > > ###################################################### > > > > # Serial baud rate (usually 19200) > > baudrate = 19200 > > > > # TCP port (when using the WeatherLinkIP) > > tcp_port = 22222 > > > > # TCP send delay (when using the WeatherLinkIP): > > tcp_send_delay = 1 > > > > # The id of your ISS station (usually 1) > > iss_id = 1 > > > > # How long to wait for a response from the station before giving up (in > > # seconds; must be greater than 2) > > timeout = 5 > > > > # How long to wait before trying again (in seconds) > > wait_before_retry = 1.2 > > > > # How many times to try before giving up: > > max_tries = 4 > > > > # The driver to use: > > driver = weewx.drivers.vantage > > > > Currently installed extensions > > Extension Name Version Description > > cmon 0.13 Collect and display computer health indicators. > > wcloud 0.10 Upload weather data to WeatherCloud. > > crt 0.13 Emit a Cumulus realtime.txt for LOOP data. > > > > Archive info > > Database name: weewx.sdb > > Table name: archive > > Unit system: 1 (US) > > First good timestamp: 2015-12-08 16:12:02 CET (1449587522) > > Last good timestamp: 2017-05-06 20:30:00 CEST (1494095400) > > Number of records: 110759 > > weewx (weewx.conf) is set to use an archive interval of 300 seconds. > > The station hardware was not interrogated in determining archive > interval. > > > > Databases configured in weewx.conf > > Database name: weewx.sdb > > Database driver: weedb.sqlite > > > > Database name: weewx > > Database driver: weedb.mysql > > Database host: localhost > > > > Database name: cmon.sdb > > Database driver: weedb.sqlite > > > > > > Parsed and obfuscated weewx.conf > > # WEEWX CONFIGURATION FILE > > # > > # Copyright (c) 2009-2015 Tom Keffer <[email protected]> > > # See the file LICENSE.txt for your rights. > > > > ############################################################ > ################## > > > > # This section is for general configuration information. > > > > # Set to 1 for extra debug info, otherwise comment it out or set to zero > > debug = 1 > > > > # Root directory of the weewx data file hierarchy for this station > > WEEWX_ROOT = / > > > > > > # How long to wait before timing out a socket (FTP, HTTP) connection > > socket_timeout = 20 > > > > # Do not modify this. It is used when installing and updating weewx. > > version = 3.7.1 > > > > ############################################################ > ################## > > > > # This section is for information about the station. > > > > [Station] > > > > # Description of the station location > > location = "EA5BY, Santa Pola (Alicante)" # REEMPLAZAR > > > > # Latitude and longitude in decimal degrees > > latitude = 38.191271 # REEMPLAZAR > > longitude = -0.582632 # REEMPLAZAR > > > > # Altitude of the station, with unit it is in. This is downloaded from > > # from the station if the hardware supports it. > > altitude = 22, meter # REEMPLAZAR > > > > # Set to type of station hardware. There must be a corresponding stanza > > # in this file with a 'driver' parameter indicating the driver to be > used. > > station_type = Vantage > > > > # The start of the rain year (1=January; 10=October, etc.). This is > > # downloaded from the station if the hardware supports it. > > rain_year_start = 1 > > > > # Start of week (0=Monday, 6=Sunday) > > week_start = 6 > > > > # If you have a website, you may specify an URL > > station_url = XXX obfuscated by wee_debug XXX > > > > ############################################################ > ################## > > > > [Vantage] > > # This section is for a Davis VantagePro2, VantageVue or WeatherLinkIP > > > > # Connection type: serial or ethernet > > # serial (the classic VantagePro) > > # ethernet (the WeatherLinkIP) > > type = serial > > > > # If the connection type is serial, a port must be specified: > > # Debian, Ubuntu, Redhat, Fedora, and SuSE: > > # /dev/ttyUSB0 is a common USB port name > > # /dev/ttyS0 is a common serial port name > > # BSD: > > # /dev/cuaU0 is a common serial port name > > port = /dev/ttyUSB0 > > # port = /dev/ttyUSB0 > > > > # If the connection type is ethernet, an IP Address/hostname is > required: > > host = 1.2.3.4 > > > > ###################################################### > > # The rest of this section rarely needs any attention. > > # You can safely leave it "as is." > > ###################################################### > > > > # Serial baud rate (usually 19200) > > baudrate = 19200 > > > > # TCP port (when using the WeatherLinkIP) > > tcp_port = 22222 > > > > # TCP send delay (when using the WeatherLinkIP): > > tcp_send_delay = 1 > > > > # The id of your ISS station (usually 1) > > iss_id = 1 > > > > # How long to wait for a response from the station before giving up (in > > # seconds; must be greater than 2) > > timeout = 5 > > > > # How long to wait before trying again (in seconds) > > wait_before_retry = 1.2 > > > > # How many times to try before giving up: > > max_tries = 4 > > > > # The driver to use: > > driver = weewx.drivers.vantage > > > > ############################################################ > ################## > > > > # This section is for uploading data to Internet si > > [StdRESTful] > > > > [[StationRegistry]] > > # To register this weather station with weewx, set this to true > > register_this_station = true > > description = EA5BY HamRadio Station # REEMPLAZAR > > station_url = XXX obfuscated by wee_debug XXX #REEMPLAZAR > > > > [[AWEKAS]] > > # This section is for configuring posts to AWEKAS. > > > > # If you wish to do this, set the option 'enable' to true, > > # and specify a username and password. > > enable = false > > username = XXX obfuscated by wee_debug XXX > > password = XXX obfuscated by wee_debug XXX > > > > [[CWOP]] > > # This section is for configuring posts to CWOP. > > > > # If you wish to do this, set the option 'enable' to true, > > # and specify the station ID (e.g., CW1234). > > enable = true > > station = XXX obfuscated by wee_debug XXX #REEMPLAZAR > > > > # If this is an APRS (radio amateur) station, uncomment > > # the following and replace with a passcode (e.g., 12345). > > passcode = 23265 # REEMPLAZAR CON NUMERO DE REGISTRO UIVIEW > > post_interval = 900 > > log_success = True > > log_failure = True > > > > [[PWSweather]] > > # This section is for configuring posts to PWSweather.com. > > > > # If you wish to do this, set the option 'enable' to true, > > # and specify a station and password. > > enable = false # REEMPLAZAR POR FALSE SI NO INTERESA > > station = XXX obfuscated by wee_debug XXX # REEMPLAZAR SI TRUE > > password = XXX obfuscated by wee_debug XXX # REEMPLAZAR SI TRUE > > > > [[WOW]] > > # This section is for configuring posts to WOW. > > > > # If you wish to do this, set the option 'enable' to true, > > # and specify a station and password. > > enable = false > > station = XXX obfuscated by wee_debug XXX > > password = XXX obfuscated by wee_debug XXX > > > > [[Wunderground]] > > # This section is for configuring posts to the Weather Underground. > > > > # If you wish to do this, set the option 'enable' to true, > > # and specify a station (e.g., 'KORHOODR3') and password. > > enable = false # REEMPLAZAR POR FALSE SI NO INTERESA > > station = XXX obfuscated by wee_debug XXX # REEMPLAZAR SI TRUE > > password = XXX obfuscated by wee_debug XXX # REMPLAZAR SI TRUE > > > > # Set the following to True to have weewx use the WU "Rapidfire" > > # protocol. Not all hardware can support it. See the User's Guide. > > rapidfire = False > > > > [[WeatherCloud]] > > id = XXX obfuscated by wee_debug XXX > > key = XXX obfuscated by wee_debug XXX > > > > ############################################################ > ################## > > > > # This section specifies what reports, using which skins, to generate. > > > > [StdReport] > > > > # Where the skins reside, relative to WEEWX_ROOT > > SKIN_ROOT = /etc/weewx/skins > > > > # Where the generated reports should go, relative to WEEWX_ROOT > > HTML_ROOT = /var/www/weewx > > > > # The database binding indicates which data should be used in reports. > > data_binding = wx_binding > > > > # Each of the following subsections defines a report that will be run. > > > > [[StandardReport]] > > # See the customizing guide to change the units, plot types and > line > > # colors, modify the fonts, display additional sensor data, and > other > > # customizations. Many of those changes can be made here by > overriding > > # parameters, or by modifying templates within the skin itself. > > > > # The StandardReport uses the 'Standard' skin, which contains the > > # images, templates and plots for the report. > > skin = Standard > > [[[Units]]] > > [[[[Groups]]]] > > group_altitude = meter > > group_speed2 = knot2 > > group_pressure = mbar > > group_rain = mm > > group_rainrate = mm_per_hour > > group_temperature = degree_C > > group_degree_day = degree_C_day > > group_speed = knot > > [[cmon]] > > HTML_ROOT = /var/www/weewx/cmon > > skin = cmon > > > > [[FTP]] > > # FTP'ing the results to a webserver is treated as just another > report, > > # albeit one with an unusual report generator! > > skin = Ftp > > # Set to True for a secure FTP (SFTP) connection. Not all servers > > # support this. > > secure_ftp = False > > > > # To upload files from something other than what HTML_ROOT is set > > # to above, specify a different HTML_ROOT here. > > #HTML_ROOT = /var/www/weewx > > > > # Most FTP servers use port 21 > > port = 21 > > > > # If you wish to use FTP, uncomment and fill out the next four > lines. > > passive = 1 > > user = XXX obfuscated by wee_debug XXX # REEMPLAZAR > > password = XXX obfuscated by wee_debug XXX # REEMPLAZAR > > server = ftp.ea5by.es # REEMPLAZAR > > path = /meteo # REEMPLAZAR > > max_tries = 3 > > > > # Set to 1 to use passive mode, zero for active mode > > > > [[RSYNC]] > > # rsync'ing to a webserver is treated as just another report > > skin = Rsync > > > > # If you wish to use rsync, you must configure passwordless ssh > using > > # public/private key authentication from the user account that > weewx > > # runs as to the user account on the remote machine where the files > > # will be copied. > > # > > # The following three lines determine where files will be sent. > > #server = replace with the rsync server name, e.g, > www.threefools.org > > #path = replace with the rsync destination directory (e.g., > /weather) > > #user = replace with the rsync username > > > > # Rsync can be configured to remove files from the remote server if > > # they don't exist under HTML_ROOT locally. USE WITH CAUTION: if > you > > # make a mistake in the remote path, you could could > unintentionally > > # cause unrelated files to be deleted. Set to 1 to enable remote > file > > # deletion, zero to allow files to accumulate remotely. > > delete = 0 > > > > ############################################################ > ################## > > > > # This service acts as a filter, converting the unit system coming from > > # the hardware to a unit system in the database. > > > > [StdConvert] > > > > # The target_unit affects only the unit system in the database. Once > > # chosen it cannot be changed without converting the entire database. > > # Modification of target_unit after starting weewx will result in > > # corrupt data - the database will contain a mix of US and METRIC data. > > # > > # The value of target_unit does not affect the unit system for > > # reporting - reports can display US, Metric, or any combination of > units. > > # > > # In most cases, target_unit should be left as the default: US > > # > > # In particular, those migrating from a standard wview installation > > # should use US since that is what the wview database contains. > > > > # DO NOT MODIFY THIS VALUE UNLESS YOU KNOW WHAT YOU ARE DOING! > > target_unit = US # Options are 'US', 'METRICWX', or 'METRIC' > > > > ############################################################ > ################## > > > > # This section can adjust data using calibration expressions. > > > > [StdCalibrate] > > > > [[Corrections]] > > # For each type, an arbitrary calibration expression can be given. > > # It should be in the units defined in the StdConvert section. > > # Example: > > foo = foo + 0.2 > > > > ############################################################ > ################## > > > > # This section is for quality control checks. If units are not specified, > > # values must be in the units defined in the StdConvert section. > > > > [StdQC] > > > > [[MinMax]] > > barometer = 26, 32.5, inHg > > outTemp = -40, 120, degree_F > > inTemp = 10, 120, degree_F > > outHumidity = 0, 100 > > inHumidity = 0, 100 > > windSpeed = 0, 120, mile_per_hour > > pressure = 24, 34.5, inHg > > > > ############################################################ > ################## > > > > # This section controls the origin of derived values. > > > > [StdWXCalculate] > > [[Calculations]] > > # Derived quantities are calculated by this service. Possible > values are: > > # hardware - use the value provided by hardware > > # software - use the value calculated by weewx > > # prefer_hardware - use value provide by hardware if available, > > # otherwise use value calculated by weewx > > > > pressure = prefer_hardware > > barometer = prefer_hardware > > altimeter = prefer_hardware > > windchill = prefer_hardware > > heatindex = prefer_hardware > > dewpoint = prefer_hardware > > inDewpoint = prefer_hardware > > rainRate = prefer_hardware > > > > ############################################################ > ################## > > > > # For hardware that supports it, this section controls how often the > > # onboard clock gets updated. > > > > [StdTimeSynch] > > > > # How often to check the weather station clock for drift (in seconds) > > clock_check = 14400 > > > > # How much it can drift before we will correct it (in seconds) > > max_drift = 5 > > > > ############################################################ > ################## > > > > # This section is for configuring the archive service. > > > > [StdArchive] > > > > # If the station hardware supports data logging then the archive > interval > > # will be downloaded from the station. Otherwise, specify it (in > seconds). > > archive_interval = 300 > > > > # How long to wait (in seconds) before processing new archive data. > Must > > # be greater than zero. > > archive_delay = 15 > > > > # If possible, new archive records are downloaded from the station > > # hardware. If the hardware does not support this, then new archive > > # records will be generated in software. > > # Set the following to "software" to force software record generation. > > record_generation = software > > > > # Whether to include LOOP data in hi/low statistics > > loop_hilo = True > > > > # The data binding used to save archive records > > data_binding = wx_binding > > > > ############################################################ > ################## > > > > # This section binds a data store to a database. > > > > [DataBindings] > > > > [[wx_binding]] > > # The database must match one of the sections in [Databases]. > > # This is likely to be the only option you would want to change. > > database = archive_sqlite > > # The name of the table within the database > > table_name = archive > > # The manager handles aggregation of data for historical summaries > > manager = weewx.wxmanager.WXDaySummaryManager > > # The schema defines the structure of the database. > > # It is *only* used when the database is created. > > schema = schemas.wview.schema > > [[cmon_binding]] > > manager = weewx.manager.DaySummaryManager > > schema = user.cmon.schema > > table_name = archive > > database = cmon_sqlite > > > > ############################################################ > ################## > > > > # This section defines various databases. > > > > [Databases] > > > > # A SQLite database is simply a single file > > [[archive_sqlite]] > > database_type = SQLite > > database_name = weewx.sdb > > > > # MySQL > > [[archive_mysql]] > > database_type = MySQL > > database_name = weewx > > [[cmon_sqlite]] > > database_name = cmon.sdb > > database_type = SQLite > > > > ############################################################ > ################## > > > > # This section defines defaults for the different types of databases. > > > > [DatabaseTypes] > > > > # Defaults for SQLite databases > > [[SQLite]] > > driver = weedb.sqlite > > # Directory in which the database files are located > > SQLITE_ROOT = /var/lib/weewx > > > > # Defaults for MySQL databases > > [[MySQL]] > > driver = weedb.mysql > > # The host where the database is located > > host = localhost > > # The user name for logging in to the host > > user = XXX obfuscated by wee_debug XXX > > # The password for the user name > > password = XXX obfuscated by wee_debug XXX > > > > ############################################################ > ################## > > > > # This section configures the internal weewx engine. > > > > [Engine] > > > > [[Services]] > > # This section specifies the services that should be run. They are > > # grouped by type, and the order of services within each group > > # determines the order in which the services will be run. > > prep_services = weewx.engine.StdTimeSynch > > data_services = , > > process_services = weewx.engine.StdConvert, > weewx.engine.StdCalibrate, weewx.engine.StdQC, > weewx.wxservices.StdWXCalculate, > user.crt.CumulusRealTime, user.cmon.ComputerMonitor > > archive_services = weewx.engine.StdArchive > > restful_services = weewx.restx.StdStationRegistry, > weewx.restx.StdWunderground, weewx.restx.StdPWSweather, > weewx.restx.StdCWOP, weewx.restx.StdWOW, weewx.restx.StdAWEKAS, > user.wcloud.WeatherCloud > > report_services = weewx.engine.StdPrint, weewx.engine.StdReport > > > > ############################################################ > ################## > > > > # Options for extension 'crt' > > [CumulusRealTime] > > filename = /var/www/weewx/realtime.txt > > unit_system = METRIC > > > > ############################################################ > ################## > > > > # Options for extension 'cmon' > > [ComputerMonitor] > > data_binding = cmon_binding > > ############################################################ > ################## > > ---------- > Ruben Navarro Huedo - EA5BZ > [email protected] > > > > *De: *Thomas Keffer <[email protected]> > *Enviado: *sábado, 6 de mayo de 2017 20:42 > *Para: *weewx-user <[email protected]> > *Asunto: *Re: [weewx-user] weewx <> Vantage Vue Problem > > > > The order in which the engine is loading services is unusual. Could you > please post the complete weewx.conf? Use the tool wee_debug, which will > obfuscate any passwords. > > > > wee_debug --info --output=/var/tmp/weewx.debug > > > > Then post the file /var/tmp/weewx.debug > > > > -tk > > > > On Sat, May 6, 2017 at 11:24 AM, Ruben Navarro Huedo <[email protected]> > wrote: > > Hello friends: > > This evening i was helping a friend with weewx and a Vantage Vue. > weewx is not reading data from Vantage Vue. > > Please...could you help me? > > Attached log and weewx.conf. > > [Vantage] > # This section is for a Davis VantagePro2, VantageVue or WeatherLinkIP > > # Connection type: serial or ethernet > # serial (the classic VantagePro) > # ethernet (the WeatherLinkIP) > type = serial > > # If the connection type is serial, a port must be specified: > # Debian, Ubuntu, Redhat, Fedora, and SuSE: > # /dev/ttyUSB0 is a common USB port name > # /dev/ttyS0 is a common serial port name > # BSD: > # /dev/cuaU0 is a common serial port name > port = /dev/ttyUSB0 > # port = /dev/ttyUSB0 > > # If the connection type is ethernet, an IP Address/hostname is > required: > host = 1.2.3.4 > > ###################################################### > # The rest of this section rarely needs any attention. > # You can safely leave it "as is." > ###################################################### > > # Serial baud rate (usually 19200) > baudrate = 19200 > > # TCP port (when using the WeatherLinkIP) > tcp_port = 22222 > > # TCP send delay (when using the WeatherLinkIP): > tcp_send_delay = 1 > > # The id of your ISS station (usually 1) > iss_id = 1 > > # How long to wait for a response from the station before giving up (in > # seconds; must be greater than 2) > timeout = 5 > > # How long to wait before trying again (in seconds) > wait_before_retry = 1.2 > > # How many times to try before giving up: > max_tries = 4 > > # The driver to use: > driver = weewx.drivers.vantage > > > > May 6 20:20:48 ea5by-meteo weewx[14206]: engine: Initializing weewx > version 3.7.1 > May 6 20:20:48 ea5by-meteo weewx[14206]: engine: Using Python 2.7.9 > (default, Mar 8 2015, 00:52:26) #012[GCC 4.9.2] > May 6 20:20:48 ea5by-meteo weewx[14206]: engine: Platform > Linux-4.1.17-v7+-armv7l-with-debian-8.0 > May 6 20:20:48 ea5by-meteo weewx[14206]: engine: Locale is 'es_ES.UTF-8' > May 6 20:20:48 ea5by-meteo weewx[14206]: engine: pid file is > /var/run/weewx.pid > May 6 20:20:48 ea5by-meteo weewx[14210]: engine: Using configuration file > /etc/weewx/weewx.conf > May 6 20:20:48 ea5by-meteo weewx[14210]: engine: debug is 1 > May 6 20:20:48 ea5by-meteo weewx[14210]: engine: Initializing engine > May 6 20:20:48 ea5by-meteo weewx[14210]: engine: Loading station type > Vantage (weewx.drivers.vantage) > May 6 20:20:48 ea5by-meteo weewx[14197]: Starting weewx weather system: > weewx. > May 6 20:20:48 ea5by-meteo systemd[1]: Started LSB: weewx weather system. > May 6 20:20:48 ea5by-meteo weewx[14210]: vantage: driver version is 3.0.10 > May 6 20:20:48 ea5by-meteo weewx[14210]: vantage: Opened up serial port > /dev/ttyUSB0; baud 19200; timeout 5.00 > May 6 20:20:49 ea5by-meteo weewx[14210]: vantage: gentle wake up of > console successful > May 6 20:20:49 ea5by-meteo weewx[14210]: vantage: _setup; hardware type > is 17 > May 6 20:20:49 ea5by-meteo weewx[14210]: engine: Loading service > weewx.engine.StdTimeSynch > May 6 20:20:49 ea5by-meteo weewx[14210]: engine: Finished loading service > weewx.engine.StdTimeSynch > May 6 20:20:49 ea5by-meteo weewx[14210]: engine: Loading service > weewx.engine.StdConvert > May 6 20:20:49 ea5by-meteo weewx[14210]: engine: StdConvert target unit > is 0x1 > May 6 20:20:49 ea5by-meteo weewx[14210]: engine: Finished loading service > weewx.engine.StdConvert > May 6 20:20:49 ea5by-meteo weewx[14210]: engine: Loading service > weewx.engine.StdCalibrate > May 6 20:20:49 ea5by-meteo weewx[14210]: engine: Finished loading service > weewx.engine.StdCalibrate > May 6 20:20:49 ea5by-meteo weewx[14210]: engine: Loading service > weewx.engine.StdQC > May 6 20:20:49 ea5by-meteo weewx[14210]: engine: Finished loading service > weewx.engine.StdQC > May 6 20:20:49 ea5by-meteo weewx[14210]: engine: Loading service > weewx.wxservices.StdWXCalculate > May 6 20:20:49 ea5by-meteo weewx[14210]: wxcalculate: The following > values will be calculated: barometer=prefer_hardware, > windchill=prefer_hardware, dewpoint=prefer_hardware, > appTemp=prefer_hardware, rainRate=prefer_hardware, windrun=prefer_hardware, > heatindex=prefer_hardware, maxSolarRad=prefer_hardware, > humidex=prefer_hardware, pressure=prefer_hardware, > inDewpoint=prefer_hardware, ET=prefer_hardware, altimeter=prefer_hardware, > cloudbase=prefer_hardware > May 6 20:20:49 ea5by-meteo weewx[14210]: wxcalculate: The following > algorithms will be used for calculations: altimeter=aaNOAA, maxSolarRad=RS > May 6 20:20:49 ea5by-meteo weewx[14210]: engine: Finished loading service > weewx.wxservices.StdWXCalculate > May 6 20:20:49 ea5by-meteo weewx[14210]: engine: Loading service > user.crt.CumulusRealTime > May 6 20:20:49 ea5by-meteo weewx[14210]: crt: service version is 0.13 > May 6 20:20:49 ea5by-meteo weewx[14210]: crt: units will be displayed as > METRIC > May 6 20:20:49 ea5by-meteo weewx[14210]: crt: binding is loop > May 6 20:20:49 ea5by-meteo weewx[14210]: crt: output goes to > /var/www/weewx/realtime.txt > May 6 20:20:49 ea5by-meteo weewx[14210]: engine: Finished loading service > user.crt.CumulusRealTime > May 6 20:20:49 ea5by-meteo weewx[14210]: engine: Loading service > user.cmon.ComputerMonitor > May 6 20:20:49 ea5by-meteo weewx[14210]: cmon: service version is 0.13 > May 6 20:20:49 ea5by-meteo weewx[14210]: manager: Daily summary version > is 1.0 > May 6 20:20:49 ea5by-meteo weewx[14210]: cmon: sysinfo: Linux ea5by-meteo > 4.1.17-v7+ #838 SMP Tue Feb 9 13:15:09 GMT 2016 armv7l > May 6 20:20:49 ea5by-meteo weewx[14210]: cmon: cpuinfo: CPU implementer: > 0x41 > May 6 20:20:49 ea5by-meteo weewx[14210]: cmon: cpuinfo: Features: half > thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm > May 6 20:20:49 ea5by-meteo weewx[14210]: cmon: cpuinfo: CPU architecture: > 7 > May 6 20:20:49 ea5by-meteo weewx[14210]: cmon: cpuinfo: BogoMIPS: 38.40 > May 6 20:20:49 ea5by-meteo weewx[14210]: cmon: cpuinfo: Hardware: BCM2709 > May 6 20:20:49 ea5by-meteo weewx[14210]: cmon: cpuinfo: CPU revision: 5 > May 6 20:20:49 ea5by-meteo weewx[14210]: cmon: cpuinfo: CPU part: 0xc07 > May 6 20:20:49 ea5by-meteo weewx[14210]: cmon: cpuinfo: model name: ARMv7 > Processor rev 5 (v7l) > May 6 20:20:49 ea5by-meteo weewx[14210]: cmon: cpuinfo: Serial: > 0000000081eaa714 > May 6 20:20:49 ea5by-meteo weewx[14210]: cmon: cpuinfo: processor: 3 > May 6 20:20:49 ea5by-meteo weewx[14210]: cmon: cpuinfo: CPU variant: 0x0 > May 6 20:20:49 ea5by-meteo weewx[14210]: cmon: cpuinfo: Revision: a01041 > May 6 20:20:49 ea5by-meteo weewx[14210]: engine: Finished loading service > user.cmon.ComputerMonitor > May 6 20:20:49 ea5by-meteo weewx[14210]: engine: Loading service > weewx.engine.StdArchive > May 6 20:20:49 ea5by-meteo weewx[14210]: engine: Archive will use data > binding wx_binding > May 6 20:20:49 ea5by-meteo weewx[14210]: engine: Record generation will > be attempted in 'software' > May 6 20:20:49 ea5by-meteo weewx[14210]: engine: The archive interval in > the configuration file (300) does not match the station hardware interval > (1800). > May 6 20:20:49 ea5by-meteo weewx[14210]: engine: Using archive interval > of 1800 seconds (specified by hardware) > May 6 20:20:49 ea5by-meteo weewx[14210]: engine: Use LOOP data in hi/low > calculations: 1 > May 6 20:20:49 ea5by-meteo weewx[14210]: manager: Daily summary version > is 1.0 > May 6 20:20:49 ea5by-meteo weewx[14210]: engine: Using binding > 'wx_binding' to database 'weewx.sdb' > May 6 20:20:49 ea5by-meteo weewx[14210]: manager: Starting backfill of > daily summaries > May 6 20:20:49 ea5by-meteo weewx[14210]: engine: Finished loading service > weewx.engine.StdArchive > May 6 20:20:49 ea5by-meteo weewx[14210]: engine: Loading service > weewx.restx.StdStationRegistry > May 6 20:20:50 ea5by-meteo weewx[14210]: restx: StationRegistry: Station > will be registered. > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Finished loading service > weewx.restx.StdStationRegistry > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Loading service > weewx.restx.StdWunderground > May 6 20:20:50 ea5by-meteo weewx[14210]: restx: Wunderground: Posting not > enabled. > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Finished loading service > weewx.restx.StdWunderground > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Loading service > weewx.restx.StdPWSweather > May 6 20:20:50 ea5by-meteo weewx[14210]: restx: PWSweather: Posting not > enabled. > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Finished loading service > weewx.restx.StdPWSweather > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Loading service > weewx.restx.StdCWOP > May 6 20:20:50 ea5by-meteo weewx[14210]: restx: CWOP: Data for station > EA5BY-13 will be posted > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Finished loading service > weewx.restx.StdCWOP > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Loading service > weewx.restx.StdWOW > May 6 20:20:50 ea5by-meteo weewx[14210]: restx: WOW: Posting not enabled. > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Finished loading service > weewx.restx.StdWOW > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Loading service > weewx.restx.StdAWEKAS > May 6 20:20:50 ea5by-meteo weewx[14210]: restx: AWEKAS: Posting not > enabled. > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Finished loading service > weewx.restx.StdAWEKAS > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Loading service > user.wcloud.WeatherCloud > May 6 20:20:50 ea5by-meteo weewx[14210]: restx: WeatherCloud: service > version is 0.10 > May 6 20:20:50 ea5by-meteo weewx[14210]: restx: WeatherCloud: Data will > be uploaded for id=53132c819d3cb39e > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Finished loading service > user.wcloud.WeatherCloud > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Loading service > weewx.engine.StdPrint > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Finished loading service > weewx.engine.StdPrint > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Loading service > weewx.engine.StdReport > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Finished loading service > weewx.engine.StdReport > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Starting up weewx > version 3.7.1 > May 6 20:20:50 ea5by-meteo weewx[14210]: vantage: gentle wake up of > console successful > May 6 20:20:50 ea5by-meteo weewx[14210]: manager: Daily summary version > is 1.0 > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Clock error is -0.10 > seconds (positive is fast) > May 6 20:20:50 ea5by-meteo weewx[14210]: vantage: Getting archive packets > since 2017-05-06 20:00:00 CEST (1494093600) > May 6 20:20:50 ea5by-meteo weewx[14210]: vantage: gentle wake up of > console successful > May 6 20:20:50 ea5by-meteo weewx[14210]: manager: Daily summary version > is 1.0 > May 6 20:20:50 ea5by-meteo weewx[14210]: vantage: Retrieving 0 page(s); > starting index= 0 > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Starting main packet > loop. > May 6 20:20:50 ea5by-meteo weewx[14210]: vantage: gentle wake up of > console successful > May 6 20:20:50 ea5by-meteo weewx[14210]: vantage: Requesting 200 LOOP > packets. > May 6 20:20:50 ea5by-meteo weewx[14210]: vantage: gentle wake up of > console successful > May 6 20:20:49 ea5by-meteo weewx[14210]: engine: Loading service > weewx.restx.StdStationRegistry > May 6 20:20:50 ea5by-meteo weewx[14210]: restx: StationRegistry: Station > will be registered. > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Finished loading service > weewx.restx.StdStationRegistry > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Loading service > weewx.restx.StdWunderground > May 6 20:20:50 ea5by-meteo weewx[14210]: restx: Wunderground: Posting not > enabled. > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Finished loading service > weewx.restx.StdWunderground > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Loading service > weewx.restx.StdPWSweather > May 6 20:20:50 ea5by-meteo weewx[14210]: restx: PWSweather: Posting not > enabled. > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Finished loading service > weewx.restx.StdPWSweather > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Loading service > weewx.restx.StdCWOP > May 6 20:20:50 ea5by-meteo weewx[14210]: restx: CWOP: Data for station > EA5BY-13 will be posted > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Finished loading service > weewx.restx.StdCWOP > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Loading service > weewx.restx.StdWOW > May 6 20:20:50 ea5by-meteo weewx[14210]: restx: WOW: Posting not enabled. > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Finished loading service > weewx.restx.StdWOW > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Loading service > weewx.restx.StdAWEKAS > May 6 20:20:50 ea5by-meteo weewx[14210]: restx: AWEKAS: Posting not > enabled. > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Finished loading service > weewx.restx.StdAWEKAS > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Loading service > user.wcloud.WeatherCloud > May 6 20:20:50 ea5by-meteo weewx[14210]: restx: WeatherCloud: service > version is 0.10 > May 6 20:20:50 ea5by-meteo weewx[14210]: restx: WeatherCloud: Data will > be uploaded for id=53132c819d3cb39e > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Finished loading service > user.wcloud.WeatherCloud > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Loading service > weewx.engine.StdPrint > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Finished loading service > weewx.engine.StdPrint > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Loading service > weewx.engine.StdReport > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Finished loading service > weewx.engine.StdReport > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Starting up weewx > version 3.7.1 > May 6 20:20:50 ea5by-meteo weewx[14210]: vantage: gentle wake up of > console successful > May 6 20:20:50 ea5by-meteo weewx[14210]: manager: Daily summary version > is 1.0 > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Clock error is -0.10 > seconds (positive is fast) > May 6 20:20:50 ea5by-meteo weewx[14210]: vantage: Getting archive packets > since 2017-05-06 20:00:00 CEST (1494093600) > May 6 20:20:50 ea5by-meteo weewx[14210]: vantage: gentle wake up of > console successful > May 6 20:20:50 ea5by-meteo weewx[14210]: manager: Daily summary version > is 1.0 > May 6 20:20:50 ea5by-meteo weewx[14210]: vantage: Retrieving 0 page(s); > starting index= 0 > May 6 20:20:50 ea5by-meteo weewx[14210]: engine: Starting main packet > loop. > May 6 20:20:50 ea5by-meteo weewx[14210]: vantage: gentle wake up of > console successful > May 6 20:20:50 ea5by-meteo weewx[14210]: vantage: Requesting 200 LOOP > packets. > May 6 20:20:50 ea5by-meteo weewx[14210]: vantage: gentle wake up of > console successful > > -- > You received this message because you are subscribed to the Google Groups > "weewx-user" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > For more options, visit https://groups.google.com/d/optout. > > > > -- > You received this message because you are subscribed to a topic in the > Google Groups "weewx-user" group. > To unsubscribe from this topic, visit https://groups.google.com/d/ > topic/weewx-user/7yYGyjs2Pms/unsubscribe. > To unsubscribe from this group and all its topics, send an email to > [email protected]. > For more options, visit https://groups.google.com/d/optout. > > > -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
