Is -p not for the ppm offset error? I think -R is the one needed to select 78 for the device type. I tried switching it around both ways, and still get the exact same error.
On Sunday, February 10, 2019 at 10:26:18 PM UTC-6, [email protected] wrote: > > You're running protocol 66 and the WH24 is 78. Try this: > > > rtl_433 -M utc -F json -p 78 -f 915000000 > > (you don't need -G here, since you don't want all protocols turned on) > Also, please post your entire weewx.conf, especially the SDR section. > > > On Sunday, February 10, 2019 at 10:09:04 PM UTC-6, N0ZO wrote: >> >> So I've wanted to use SDR to capture the data of the ObserverIP that I >> have. I have the WS-1400-IP which is a rebranded HP-1000 by Fine Offset. >> It took me forever to actually get where my Pi3B could read the data from >> the SDR. But now I finally got that working when I setup weewx by the >> setup.py method. >> >> Now I have hit a block that I'm not sure I can figure out, especially >> since I'm not finding anything of a fix on the internet. >> >> Running sudo PYTHONPATH=bin python bin/user/sdr.py --cmd="rtl_433 -M utc >>> -F json -G -p 66 -f 915000000" >> >> >> gives me this: >> >> out: ['{"time" : "2019-02-11 03:44:32", "model" : "Fine Offset WH24", >>> "id" : 140, "temperature_C" : 12.600, "humidity" : 80, "wind_dir_deg" : >>> 111, "wind_speed_ms" : 0.280, "gust_speed_ms" : 1.120, "rainfall_mm" : >>> 1150.800, "uv" : 1, "uvi" : 0, "light_lux" : 0.000, "battery" : "OK", "mic" >>> : "CRC"}\n', '{"time" : "2019-02-11 03:44:33", "model" : "Fine Offset >>> Electronics, WH25", "id" : 104, "temperature_C" : 20.000, "humidity" : 57, >>> "pressure_hPa" : 1004.100, "battery" : "OK", "mic" : "CHECKSUM"}\n'] >>> parsed: {'temperature.104.FOWH25Packet': 20.0, >>> 'battery.104.FOWH25Packet': 0, 'dateTime': 1549856673, >>> 'humidity.104.FOWH25Packet': 57.0, 'pressure.104.FOWH25Packet': 1004.1, >>> 'usUnits': 16} >>> out: ['{"time" : "2019-02-11 03:44:48", "model" : "Fine Offset WH24", >>> "id" : 140, "temperature_C" : 12.600, "humidity" : 80, "wind_dir_deg" : >>> 109, "wind_speed_ms" : 0.980, "gust_speed_ms" : 1.120, "rainfall_mm" : >>> 1150.800, "uv" : 1, "uvi" : 0, "light_lux" : 0.000, "battery" : "OK", "mic" >>> : "CRC"}\n'] >> >> >> Under parsed I get that I can now enter the temperature.104.FOWH25Packet >> under the [[Sensor_map]] under SDR. I also understand that my indoor >> device is the Fine Offset WH25, and the outdoor is the Fine Offset WH24. >> But part of what I can't figure out is this: >> It gave me the detail I needed for the Sensor_Map when it parsed the >> WH25, but it didn't do that for WH24. I think my questions may be linked in >> a way since it didn't parse that out. >> >> Now, when I run weewx instead of the sdr.py, I get this: >> >> Feb 10 21:50:27 raspberrypi weewx[2692]: sdr: MainThread: parse_json: >>>> unknown model Fine Offset WH24 >>> >>> Feb 10 21:50:27 raspberrypi weewx[2692]: sdr: MainThread: punt >>>> unrecognized line '{"time" : "2019-02-11 03:50:24", "model" : "Fine Offset >>>> WH24", "id" : 140, "temperature_C" : 12.600, "humidity" : 81, >>>> "wind_dir_deg" : 152, "wind_speed_ms" : 0.840, "gust_speed_ms" : 1.120, >>>> "rainfall_mm" : 1150.800, "uv" : 1, "uvi" : 0, "light_lux" : 0.000, >>>> "battery" : "OK", "mic" : "CRC"}#012' >>> >>> Weewx is generating without error, and even has the inside temperature >> on the page it generated in public_html >> >> I can provide actual logs if needed, but I'm thinking it's some issue >> that I'm not seeing either with rtl_433 or something I missed in a setting >> with weewx. >> >> Also, I'm not sure if it matters or not, but I ran this line under SDR so >> that it captured data: >> >> cmd= rtl_433 -M utc -F json -G -p 66 -f 915000000 >> >> >> >> >> -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
# WEEWX CONFIGURATION FILE # # Copyright (c) 2009-2019 Tom Keffer <[email protected]> # See the file LICENSE.txt for your rights. ############################################################################## # This section is for general configuration information. # Set to 1 for extra debug info, otherwise comment it out or set to zero debug = 1 # Root directory of the weewx data file hierarchy for this station WEEWX_ROOT = /home/weewx # Whether to log successful operations log_success = True # Whether to log unsuccessful operations log_failure = True # How long to wait before timing out a socket (FTP, HTTP) connection socket_timeout = 20 # Do not modify this. It is used when installing and updating weewx. version = 3.9.1 ############################################################################## # This section is for information about the station. [Station] # Description of the station location location = "Calera, AL" # Latitude and longitude in decimal degrees latitude = 33.101070 longitude = -86.752403 # Altitude of the station, with unit it is in. This is downloaded from # from the station if the hardware supports it. altitude = 515, foot # Choose 'foot' or 'meter' for unit # Set to type of station hardware. There must be a corresponding stanza # in this file with a 'driver' parameter indicating the driver to be used. station_type = SDR # If you have a website, you may specify an URL #station_url = http://www.example.com # The start of the rain year (1=January; 10=October, etc.). This is # downloaded from the station if the hardware supports it. rain_year_start = 1 # Start of week (0=Monday, 6=Sunday) week_start = 6 ############################################################################## [SDR] # This section is for the software-defined radio driver. # The driver to use driver = user.sdr log_unknown_sensors = True log_unmapped_sensors = True cmd= rtl_433 -M utc -F json -R 78 -p 66 -f 915000000 [[sensor_map]] inTemp = temperature.104.FOWH25Packet #Living Room Temp inHumidity = humidity.104.FOWH25Packet #Living Room Humidity #pressure = pressure.104.FOWH25Packet ############################################################################## [Simulator] # This section is for the weewx weather station simulator # The time (in seconds) between LOOP packets. loop_interval = 2.5 # The simulator mode can be either 'simulator' or 'generator'. # Real-time simulator. Sleep between each LOOP packet. mode = simulator # Generator. Emit LOOP packets as fast as possible (useful for testing). #mode = generator # The start time. Format is YYYY-mm-ddTHH:MM. If not specified, the default # is to use the present time. #start = 2011-01-01T00:00 # The driver to use: driver = weewx.drivers.simulator ############################################################################## # This section is for uploading data to Internet sites [StdRESTful] [[StationRegistry]] # To register this weather station with weewx, set this to true register_this_station = false [[AWEKAS]] # This section is for configuring posts to AWEKAS. # If you wish to do this, set the option 'enable' to true, # and specify a username and password. # To guard against parsing errors, put the password in quotes. enable = false username = replace_me password = replace_me [[CWOP]] # This section is for configuring posts to CWOP. # If you wish to do this, set the option 'enable' to true, # and specify the station ID (e.g., CW1234). enable = false station = replace_me # If this is an APRS (radio amateur) station, uncomment # the following and replace with a passcode (e.g., 12345). #passcode = replace_me (APRS stations only) [[PWSweather]] # This section is for configuring posts to PWSweather.com. # If you wish to do this, set the option 'enable' to true, # and specify a station and password. # To guard against parsing errors, put the password in quotes. enable = false station = replace_me password = replace_me [[WOW]] # This section is for configuring posts to WOW. # If you wish to do this, set the option 'enable' to true, # and specify a station and password. # To guard against parsing errors, put the password in quotes. enable = false station = replace_me password = replace_me [[Wunderground]] # This section is for configuring posts to the Weather Underground. # If you wish to do this, set the option 'enable' to true, # and specify a station (e.g., 'KORHOODR3') and password. # To guard against parsing errors, put the password in quotes. enable = false station = replace_me password = replace_me # Set the following to True to have weewx use the WU "Rapidfire" # protocol. Not all hardware can support it. See the User's Guide. rapidfire = False ############################################################################## # This section specifies what reports, using which skins, to generate. [StdReport] # Where the skins reside, relative to WEEWX_ROOT SKIN_ROOT = skins # Where the generated reports should go, relative to WEEWX_ROOT HTML_ROOT = public_html # The database binding indicates which data should be used in reports. data_binding = wx_binding # Whether to log a successful operation log_success = True # Whether to log an unsuccessful operation log_failure = False # Each of the following subsections defines a report that will be run. # See the customizing guide to change the units, plot types and line # colors, modify the fonts, display additional sensor data, and other # customizations. Many of those changes can be made here by overriding # parameters, or by modifying templates within the skin itself. [[SeasonsReport]] # The SeasonsReport uses the 'Seasons' skin, which contains the # images, templates and plots for the report. skin = Seasons enable = true [[SmartphoneReport]] # The SmartphoneReport uses the 'Smartphone' skin, and the images and # files are placed in a dedicated subdirectory. skin = Smartphone enable = false HTML_ROOT = public_html/smartphone [[MobileReport]] # The MobileReport uses the 'Mobile' skin, and the images and files # are placed in a dedicated subdirectory. skin = Mobile enable = false HTML_ROOT = public_html/mobile [[StandardReport]] # This is the old "Standard" skin. By default, it is not enabled. skin = Standard enable = false [[FTP]] # FTP'ing the results to a webserver is treated as just another report, # albeit one with an unusual report generator! skin = Ftp # If you wish to use FTP, set "enable" to "true", then # fill out the next four lines. # Use quotes around passwords to guard against parsing errors. enable = false user = replace_me password = replace_me server = replace_me # The ftp server name, e.g, www.myserver.org path = replace_me # The destination directory, e.g., /weather # Set to True for an FTP over TLS (FTPS) connection. Not all servers # support this. secure_ftp = False # To upload files from something other than what HTML_ROOT is set # to above, specify a different HTML_ROOT here. #HTML_ROOT = public_html # Most FTP servers use port 21 port = 21 # Set to 1 to use passive mode, zero for active mode passive = 1 [[RSYNC]] # rsync'ing to a webserver is treated as just another report skin = Rsync # If you wish to use rsync, you must configure passwordless ssh using # public/private key authentication from the user account that weewx # runs to the user account on the remote machine where the files # will be copied. # # If you wish to use rsync, set "enable" to "true", then # fill out server, user, and path. # The server should appear in your .ssh/config file. # The user is the username used in the identity file. # The path is the destination directory, such as /var/www/html/weather. # Be sure that the user has write permissions on the destination! enable = false server = replace_me user = replace_me path = replace_me # To upload files from something other than what HTML_ROOT is set # to above, specify a different HTML_ROOT here. #HTML_ROOT = public_html # Rsync can be configured to remove files from the remote server if # they don't exist under HTML_ROOT locally. USE WITH CAUTION: if you # make a mistake in the remote path, you could could unintentionally # cause unrelated files to be deleted. Set to 1 to enable remote file # deletion, zero to allow files to accumulate remotely. delete = 0 #### # Various options for customizing your reports. [[Defaults]] [[[Units]]] # The following section sets what unit to use for each unit group. # NB: The unit is always in the singular. I.e., 'mile_per_hour', # NOT 'miles_per_hour' [[[[Groups]]]] group_altitude = foot # Options are 'foot' or 'meter' group_degree_day = degree_F_day # Options are 'degree_F_day' or 'degree_C_day' group_pressure = inHg # Options are 'inHg', 'mmHg', 'mbar', or 'hPa' group_rain = inch # Options are 'inch', 'cm', or 'mm' group_rainrate = inch_per_hour # Options are 'inch_per_hour', 'cm_per_hour', or 'mm_per_hour' group_speed = mile_per_hour # Options are 'mile_per_hour', 'km_per_hour', 'knot', or 'meter_per_second' group_speed2 = mile_per_hour2 # Options are 'mile_per_hour2', 'km_per_hour2', 'knot2', or 'meter_per_second2' group_temperature = degree_F # Options are 'degree_F' or 'degree_C' # The following section sets the formatting for each type of unit. [[[[StringFormats]]]] centibar = %.0f cm = %.2f cm_per_hour = %.2f degree_C = %.1f degree_F = %.1f degree_compass = %.0f foot = %.0f hPa = %.1f hour = %.1f inHg = %.3f inch = %.2f inch_per_hour = %.2f km_per_hour = %.0f km_per_hour2 = %.1f knot = %.0f knot2 = %.1f mbar = %.1f meter = %.0f meter_per_second = %.1f meter_per_second2 = %.1f mile_per_hour = %.0f mile_per_hour2 = %.1f mm = %.1f mmHg = %.1f mm_per_hour = %.1f percent = %.0f second = %.0f uv_index = %.1f volt = %.1f watt_per_meter_squared = %.0f NONE = " N/A" # The following section sets the label for each type of unit [[[[Labels]]]] day = " day", " days" hour = " hour", " hours" minute = " minute", " minutes" second = " second", " seconds" NONE = "" # The following section sets the format for each time scale. # The values below will work in every locale, but they may not look # particularly attractive. [[[[TimeFormats]]]] hour = %H:%M day = %X week = %X (%A) month = %x %X year = %x %X rainyear = %x %X current = %x %X ephem_day = %X ephem_year = %x %X [[[[Ordinates]]]] # Ordinal directions. The last one is for no wind direction directions = N, NNE, NE, ENE, E, ESE, SE, SSE, S, SSW, SW, WSW, W, WNW, NW, NNW, N/A # The following section sets the base temperatures used for the # calculation of heating and cooling degree-days. [[[[[DegreeDays]]]]] # Base temperature for heating days, with unit: heating_base = 65, degree_F # Base temperature for cooling days, with unit: cooling_base = 65, degree_F # A trend takes a difference across a time period. The following # section sets the time period, and how big an error is allowed to # still be counted as the start or end of a period. [[[[[Trend]]]]] time_delta = 10800 # 3 hours time_grace = 300 # 5 minutes # The labels to be used for each observation type [[[Labels]]] # Set to hemisphere abbreviations suitable for your location: hemispheres = N, S, E, W # Formats to be used for latitude whole degrees, longitude whole # degrees, and minutes: latlon_formats = %02d, %03d, %05.2f # Generic labels, keyed by an observation type. [[[[Generic]]]] barometer = Barometer dewpoint = Dew Point ET = ET heatindex = Heat Index inHumidity = Inside Humidity inTemp = Inside Temperature outHumidity = Humidity outTemp = Outside Temperature radiation = Radiation rain = Rain rainRate = Rain Rate UV = UV Index windDir = Wind Direction windGust = Gust Speed windGustDir = Gust Direction windSpeed = Wind Speed windchill = Wind Chill windgustvec = Gust Vector windvec = Wind Vector extraTemp1 = Temperature1 extraTemp2 = Temperature2 extraTemp3 = Temperature3 # Sensor status indicators rxCheckPercent = Signal Quality txBatteryStatus = Transmitter Battery windBatteryStatus = Wind Battery rainBatteryStatus = Rain Battery outTempBatteryStatus = Outside Temperature Battery inTempBatteryStatus = Inside Temperature Battery consBatteryVoltage = Console Battery heatingVoltage = Heating Battery supplyVoltage = Supply Voltage referenceVoltage = Reference Voltage [[[Almanac]]] # The labels to be used for the phases of the moon: moon_phases = New, Waxing crescent, First quarter, Waxing gibbous, Full, Waning gibbous, Last quarter, Waning crescent ############################################################################## # This service acts as a filter, converting the unit system coming from # the hardware to a unit system in the database. [StdConvert] # The target_unit affects only the unit system in the database. Once # chosen it cannot be changed without converting the entire database. # Modification of target_unit after starting weewx will result in # corrupt data - the database will contain a mix of US and METRIC data. # # The value of target_unit does not affect the unit system for # reporting - reports can display US, Metric, or any combination of units. # # In most cases, target_unit should be left as the default: US # # In particular, those migrating from a standard wview installation # should use US since that is what the wview database contains. # DO NOT MODIFY THIS VALUE UNLESS YOU KNOW WHAT YOU ARE DOING! target_unit = US # Options are 'US', 'METRICWX', or 'METRIC' ############################################################################## # This section can adjust data using calibration expressions. [StdCalibrate] [[Corrections]] # For each type, an arbitrary calibration expression can be given. # It should be in the units defined in the StdConvert section. # Example: foo = foo + 0.2 ############################################################################## # This section is for quality control checks. If units are not specified, # values must be in the units defined in the StdConvert section. [StdQC] [[MinMax]] barometer = 26, 32.5, inHg pressure = 24, 34.5, inHg outTemp = -40, 120, degree_F inTemp = 10, 120, degree_F outHumidity = 0, 100 inHumidity = 0, 100 windSpeed = 0, 120, mile_per_hour rain = 0, 10, inch ############################################################################## # This section controls the origin of derived values. [StdWXCalculate] [[Calculations]] # How to calculate derived quantities. Possible values are: # hardware - use the value provided by hardware # software - use the value calculated by weewx # prefer_hardware - use value provide by hardware if available, # otherwise use value calculated by weewx pressure = prefer_hardware barometer = prefer_hardware altimeter = prefer_hardware windchill = prefer_hardware heatindex = prefer_hardware dewpoint = prefer_hardware inDewpoint = prefer_hardware rainRate = prefer_hardware ############################################################################## # For hardware that supports it, this section controls how often the # onboard clock gets updated. [StdTimeSynch] # How often to check the weather station clock for drift (in seconds) clock_check = 14400 # How much it can drift before we will correct it (in seconds) max_drift = 5 ############################################################################## # This section is for configuring the archive service. [StdArchive] # If the station hardware supports data logging then the archive interval # will be downloaded from the station. Otherwise, specify it (in seconds). archive_interval = 300 # If possible, new archive records are downloaded from the station # hardware. If the hardware does not support this, then new archive # records will be generated in software. # Set the following to "software" to force software record generation. record_generation = hardware # Whether to include LOOP data in hi/low statistics loop_hilo = True # The data binding used to save archive records data_binding = wx_binding ############################################################################## # This section binds a data store to a database. [DataBindings] [[wx_binding]] # The database must match one of the sections in [Databases]. # This is likely to be the only option you would want to change. database = archive_sqlite # The name of the table within the database table_name = archive # The manager handles aggregation of data for historical summaries manager = weewx.wxmanager.WXDaySummaryManager # The schema defines the structure of the database. # It is *only* used when the database is created. schema = schemas.wview.schema ############################################################################## # This section defines various databases. [Databases] # A SQLite database is simply a single file [[archive_sqlite]] database_name = weewx.sdb database_type = SQLite # MySQL [[archive_mysql]] database_name = weewx database_type = MySQL ############################################################################## # This section defines defaults for the different types of databases. [DatabaseTypes] # Defaults for SQLite databases [[SQLite]] driver = weedb.sqlite # Directory in which the database files are located SQLITE_ROOT = %(WEEWX_ROOT)s/archive # Defaults for MySQL databases [[MySQL]] driver = weedb.mysql # The host where the database is located host = localhost # The user name for logging in to the host user = weewx # The password for the user name (quotes guard against parsing errors) password = weewx ############################################################################## # This section configures the internal weewx engine. [Engine] [[Services]] # This section specifies the services that should be run. They are # grouped by type, and the order of services within each group # determines the order in which the services will be run. prep_services = weewx.engine.StdTimeSynch data_services = , process_services = weewx.engine.StdConvert, weewx.engine.StdCalibrate, weewx.engine.StdQC, weewx.wxservices.StdWXCalculate archive_services = weewx.engine.StdArchive restful_services = weewx.restx.StdStationRegistry, weewx.restx.StdWunderground, weewx.restx.StdPWSweather, weewx.restx.StdCWOP, weewx.restx.StdWOW, weewx.restx.StdAWEKAS report_services = weewx.engine.StdPrint, weewx.engine.StdReport
