Tom, My bad. I wasn’t stopping weewx before trying the wee_device commands. With weewx stopped it works perfectly. Thanks, Allan
> On Jul 25, 2019, at 8:09 AM, Thomas Keffer <[email protected]> wrote: > > It does. In fact, that's what I use. > > It's not, by chance, an Envoy 8x? If so, we do not support it. > > If it is a regular Envoy, we'll have to see the log. It may have a few useful > clues. > > > >> On Thu, Jul 25, 2019 at 10:27 AM Allan Tyson <[email protected]> wrote: >> I tried that. I get an unrecognized hardware error and it doesn’t complete. >> Same if I try the wee_device —info >> Does the Vantage driver not support the Weather Envoy ?. >> >>> On Jul 25, 2019, at 4:20 AM, Thomas Keffer <[email protected]> wrote: >>> >> >> >>> Use wee_device with the --clear-memory option. Be sure to stop weewx first. >>> >>> -tk >>> >>>> On Thu, Jul 25, 2019 at 2:48 AM Allan Tyson <[email protected]> wrote: >>>> I have a Davis USB Westher Envoy connected to an RPi running weewx. It was >>>> running fine but I stopped weewx on the RPi and disconnected the Weather >>>> Envoy USB cable from the RPi to connect it to another RPi I was using to >>>> install Raspbian Buster with weewx on a smaller micro SD card so I could >>>> save it’s image to a smaller backup image file having originally >>>> installed it on an internal 120GB SSD drive. >>>> The new installation worked just great but when I reconnected the Weather >>>> Envoy to the original RPi I discovered that the USB loggers’s memory was >>>> somehow corrupted so that weewx would no longer update Nginx. I cleared >>>> the memory by connecting the Logger to my Mac laptop & used WeatherLink to >>>> clear the archive memory. >>>> There was a Post by Tom in 2012 saying you could change the configuration >>>> of a weather envoy using the config utility in weewx as well as using the >>>> WeatherLink software. I did see the instructions for using wee_device to >>>> change the parameters of the Davis driver but when running it I get an >>>> unrecognized hardware error and the Weather Envoy isn’t listed as being >>>> supported hardware in the list of supported hardware. Only the Vantsge >>>> Vue and Vantsge Pro2 Consoles are listed though in the pictorial list of >>>> supported hardware the Weather Envoy is shown. >>>> Is there a way of clearing the Weather Envoy archive memory from the >>>> command line of the RPi so I can clear it without having to stop the RPI, >>>> disconnect the Envoy USB cable and connect it to my laptop to use the >>>> WeatherLink software to perform the clearing and then have to reconnect it >>>> to my RPi ?. >>>> >>>> Allan >>>> >>>> -- >>>> You received this message because you are subscribed to the Google Groups >>>> "weewx-user" group. >>>> To unsubscribe from this group and stop receiving emails from it, send an >>>> email to [email protected]. >>>> To view this discussion on the web visit >>>> https://groups.google.com/d/msgid/weewx-user/e122fd87-079c-4c63-83ff-44ca9bb88cc4%40googlegroups.com. >>> >>> -- >>> You received this message because you are subscribed to the Google Groups >>> "weewx-user" group. >>> To unsubscribe from this group and stop receiving emails from it, send an >>> email to [email protected]. >> >>> To view this discussion on the web visit >>> https://groups.google.com/d/msgid/weewx-user/CAPq0zEBnKYkf3XttDegi%2BCP_jFeGYdoV-D34y-8p4aVJPLBVJw%40mail.gmail.com. >> >> -- >> You received this message because you are subscribed to the Google Groups >> "weewx-user" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> To view this discussion on the web visit >> https://groups.google.com/d/msgid/weewx-user/0DABB0BE-FA73-439B-B274-C6DA0E06DEE8%40gmail.com. > -- > -tk > -- > You received this message because you are subscribed to the Google Groups > "weewx-user" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/weewx-user/CAPq0zEBVSFsjDgBxVgOz6xh2rQVXNCfr78GGnSpBKnccCCwmTg%40mail.gmail.com. -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/weewx-user/E09B5E0C-0C84-4118-B540-4DD5054FCD50%40gmail.com.
