Well, geez, we're not trying to fix the working system. Try it on the broken system.
On Wed, Apr 21, 2021 at 5:21 PM Dave McCreath <[email protected]> wrote: > Tom > > Please be aware that my answer is for the current working system, not the > one that was broken. > > I can try the RPi upgrade again and see if the file is located within the > devices directory? > > Dave > > On Thursday, 22 April 2021 at 01:14:53 UTC+1 Dave McCreath wrote: > >> Tom >> >> >> >> Hi. >> >> >> >> Yep, mine is the same as yours: >> >> >> >> [ 4689.183852] cp210x ttyUSB0: cp210x converter now disconnected from >> ttyUSB0 >> >> [ 4689.183939] cp210x 1-1.4:1.0: device disconnected >> >> [ 4689.633565] usb 1-1.4: new full-speed USB device number 5 using >> xhci_hcd >> >> [ 4692.803586] usb 1-1.4: new full-speed USB device number 6 using >> xhci_hcd >> >> [ 4692.938998] usb 1-1.4: New USB device found, idVendor=10c4, >> idProduct=ea60, bcdDevice= 1.00 >> >> [ 4692.939011] usb 1-1.4: New USB device strings: Mfr=1, Product=2, >> SerialNumber=3 >> >> [ 4692.939021] usb 1-1.4: Product: CP2102 USB to UART Bridge Controller >> >> [ 4692.939031] usb 1-1.4: Manufacturer: Silicon Labs >> >> [ 4692.939040] usb 1-1.4: SerialNumber: 0001 >> >> [ 4692.946665] cp210x 1-1.4:1.0: cp210x converter detected >> >> [ 4692.952907] usb 1-1.4: cp210x converter now attached to ttyUSB0 >> >> [ 4693.217302] usb 1-1.4: USB disconnect, device number 6 >> >> [ 4693.217689] cp210x ttyUSB0: cp210x converter now disconnected from >> ttyUSB0 >> >> [ 4693.217742] cp210x 1-1.4:1.0: device disconnected >> >> [ 4693.513548] usb 1-1.4: new full-speed USB device number 7 using >> xhci_hcd >> >> [ 4693.648964] usb 1-1.4: New USB device found, idVendor=10c4, >> idProduct=ea60, bcdDevice= 1.00 >> >> [ 4693.648972] usb 1-1.4: New USB device strings: Mfr=1, Product=2, >> SerialNumber=3 >> >> [ 4693.648979] usb 1-1.4: Product: CP2102 USB to UART Bridge Controller >> >> [ 4693.648986] usb 1-1.4: Manufacturer: Silicon Labs >> >> [ 4693.648992] usb 1-1.4: SerialNumber: 0001 >> >> [ 4693.652553] cp210x 1-1.4:1.0: cp210x converter detected >> >> [ 4693.657075] usb 1-1.4: cp210x converter now attached to ttyUSB0 >> >> pi@raspberrypi:~ $ >> >> >> >> Regards >> >> >> >> Dave >> >> >> >> *From:* [email protected] <[email protected]> *On Behalf >> Of *Tom Keffer >> *Sent:* 22 April 2021 01:07 >> *To:* weewx-user <[email protected]> >> *Subject:* Re: [weewx-user] Re: RPi WeeWx Python 3.7 Issue >> >> >> >> Do you have a device /dev/ttyUSB0? That's normally where a Vantage shows >> up in the device directory, but not always. >> >> >> >> The most reliable way to find out where the Vantage ended up is to unplug >> it, plug it in again, then type 'dmesg'. This will look something like: >> >> >> >> *dmesg* >> >> [14818.699217] usb 2-2.1: USB disconnect, device number 4 >> [14818.699660] pl2303 ttyUSB0: pl2303 converter now disconnected from >> ttyUSB0 >> [14818.699710] pl2303 2-2.1:1.0: device disconnected >> [14820.731608] usb 2-2.1: new full-speed USB device number 10 using >> xhci_hcd >> [14820.844750] usb 2-2.1: New USB device found, idVendor=05ad, >> idProduct=0fba, bcdDevice= 3.00 >> [14820.844756] usb 2-2.1: New USB device strings: Mfr=1, Product=2, >> SerialNumber=0 >> [14820.844759] usb 2-2.1: Product: USB-Serial Controller >> [14820.844761] usb 2-2.1: Manufacturer: Prolific Technology Inc. >> [14820.852720] pl2303 2-2.1:1.0: pl2303 converter detected >> [14820.856368] usb 2-2.1: pl2303 converter now attached to ttyUSB0 >> >> >> >> In my case, the serial-to-usb converter showed up at /dev/ttyUSB0, but >> your results may differ. >> >> >> >> -tk >> >> >> >> On Wed, Apr 21, 2021 at 4:34 PM Dave McCreath <[email protected]> >> wrote: >> >> Forgot to add. >> >> >> >> Now running 4.5.1 from a backup SD card and all is currently well but >> does not look like I'll be able to update/upgrade the RPi until I figure >> out what's wrong. >> >> >> >> Regards >> >> >> >> Dave >> >> On Thursday, 22 April 2021 at 00:08:18 UTC+1 Dave McCreath wrote: >> >> Good Evening Venerable Experts >> >> >> >> Earlier on today I updated my RPi (sudu apt-get update && sudo apt-get >> upgrade). On rebooting WeeWx failed to start, this was post an upgrade >> from 4.2 to 4.5.1. (I have WeeWx added to the sources list) >> >> >> >> So, being savvy, rebooted from a backup sd card to bring the system back >> to where it was prior to the update/upgrade and WeeWx version 4.2. >> >> >> >> I then went about updating/upgrading WeeWx from 4.2 to 4.5 (sudo apt-get >> install weewx), that went fine, rebooted and WeeWx ran without any issues >> post the upgrade. >> >> >> >> Next I then tried sudu apt-get update && sudo apt-get upgrade again. >> Post a reboot, exactly the same issue as before, WeeWx would not start: >> >> >> >> pi@raspberrypi:~ $ service weewx status >> >> ● weewx.service - LSB: weewx weather system >> >> Loaded: loaded (/etc/init.d/weewx; generated) >> >> Active: active (exited) since Wed 2021-04-21 23:48:06 BST; 2min 28s ago >> >> Docs: man:systemd-sysv-generator(8) >> >> Process: 338 ExecStart=/etc/init.d/weewx start (code=exited, >> status=0/SUCCESS) >> >> >> >> Apr 21 23:48:06 raspberrypi python3[611]: weewx[611] CRITICAL >> weewx.engine: **** self.port.openPort() >> >> Apr 21 23:48:06 raspberrypi python3[611]: weewx[611] CRITICAL >> weewx.engine: **** File "/usr/share/weewx/weewx/drivers/vantage.py", >> line 308, in openPort >> >> Apr 21 23:48:06 raspberrypi python3[611]: weewx[611] CRITICAL >> weewx.engine: **** self.serial_port = serial.Serial(self.port, >> self.baudrate, timeout=self.timeout) >> >> Apr 21 23:48:06 raspberrypi python3[611]: weewx[611] CRITICAL >> weewx.engine: **** File >> "/usr/lib/python3/dist-packages/serial/serialutil.py", line 240, in __init__ >> >> Apr 21 23:48:06 raspberrypi python3[611]: weewx[611] CRITICAL >> weewx.engine: **** self.open() >> >> Apr 21 23:48:06 raspberrypi python3[611]: weewx[611] CRITICAL >> weewx.engine: **** File >> "/usr/lib/python3/dist-packages/serial/serialposix.py", line 268, in open >> >> Apr 21 23:48:06 raspberrypi python3[611]: weewx[611] CRITICAL >> weewx.engine: **** raise SerialException(msg.errno, "could not >> open port {}: {}".format(self._port, msg)) >> >> Apr 21 23:48:06 raspberrypi python3[611]: weewx[611] CRITICAL >> weewx.engine: **** serial.serialutil.SerialException: [Errno 2] could >> not open port /dev/ttyUSB0: [Errno 2] No such file or directory: >> '/dev/ttyUSB0' >> >> Apr 21 23:48:06 raspberrypi python3[611]: weewx[611] CRITICAL __main__: >> Unable to load driver: [Errno 2] could not open port /dev/ttyUSB0: [Errno >> 2] No such file or directory: '/dev/ttyUSB0' >> >> Apr 21 23:48:06 raspberrypi python3[611]: weewx[611] CRITICAL >> __main__: **** Exiting... >> >> >> >> Any ideas? >> >> -- >> You received this message because you are subscribed to the Google Groups >> "weewx-user" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> To view this discussion on the web visit >> https://groups.google.com/d/msgid/weewx-user/27e48fc1-8ea2-44c7-bdaa-73cfb1c15dcen%40googlegroups.com >> <https://groups.google.com/d/msgid/weewx-user/27e48fc1-8ea2-44c7-bdaa-73cfb1c15dcen%40googlegroups.com?utm_medium=email&utm_source=footer> >> . >> >> -- >> You received this message because you are subscribed to a topic in the >> Google Groups "weewx-user" group. >> To unsubscribe from this topic, visit >> https://groups.google.com/d/topic/weewx-user/8CM2mGJ4eh8/unsubscribe. >> To unsubscribe from this group and all its topics, send an email to >> [email protected]. >> To view this discussion on the web visit >> https://groups.google.com/d/msgid/weewx-user/CAPq0zECZ4Z%3DFCUUjoGFqJAgVkMg-WAiD6YpV2RXo69uMtAv7%2BA%40mail.gmail.com >> <https://groups.google.com/d/msgid/weewx-user/CAPq0zECZ4Z%3DFCUUjoGFqJAgVkMg-WAiD6YpV2RXo69uMtAv7%2BA%40mail.gmail.com?utm_medium=email&utm_source=footer> >> . >> > -- > You received this message because you are subscribed to the Google Groups > "weewx-user" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/weewx-user/79f2b133-943c-487f-9038-a0d0458110ccn%40googlegroups.com > <https://groups.google.com/d/msgid/weewx-user/79f2b133-943c-487f-9038-a0d0458110ccn%40googlegroups.com?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/weewx-user/CAPq0zEAK5P6Ad5HYCmLAqJBXPfsGoVZ1tk%2BLZJ0tiBSrkmD6bg%40mail.gmail.com.
