Here's my entire interceptor driver output, if it helps.
raw data:
b'PASSKEY=XXXX&stationtype=EasyWeatherPro_V5.1.1&runtime=4&dateutc=2023-08-04+19:01:54&tempinf=73.2&humidityin=47&baromrelin=29.229&baromabsin=29.229&tempf=91.6&humidity=41&winddir=246&windspeedmph=4.03&windgustmph=4.25&maxdailygust=8.72&solarradiation=817.36&uv=7&rrain_piezo=0.000&erain_piezo=0.000&hrain_piezo=0.000&drain_piezo=0.000&wrain_piezo=0.000&mrain_piezo=0.000&yrain_piezo=0.000&ws90cap_volt=5.4&ws90_ver=133&gain10_piezo=1.00&gain20_piezo=1.00&gain30_piezo=1.00&gain40_piezo=1.00&gain50_piezo=1.00&wh90batt=3.14&freq=915M&model=HP2564BU_Pro_V1.9.0&interval=30'
raw packet: {'dateTime': 1691175714, 'usUnits': 1, 'temperature_in': 73.2,
'humidity_in': 47.0, 'pressure': 29.229, 'temperature_out': 91.6,
'humidity_out': 41.0, 'wind_dir': 246.0, 'wind_speed': 4.03, 'wind_gust':
4.25, 'solar_radiation': 817.36, 'uv': 7.0}
mapped packet: {'dateTime': 1691175714, 'usUnits': 1, 'pressure': 29.229,
'outHumidity': 41.0, 'inHumidity': 47.0, 'outTemp': 91.6, 'inTemp': 73.2,
'windSpeed': 4.03, 'windGust': 4.25, 'windDir': 246.0, 'radiation': 817.36,
'UV': 7.0}
I'm missing something. I have the driver configured as such:
[Interceptor]
driver = user.interceptor
device_type = ecowitt-client
port = 8001
...
[[sensor_map_extensions]]
inTemp = temperature_in
inHumidity = humidity_in
outTemp = temperature_out
outHumidity = humidity_out
dateTime = dateTime
usUnits = usUnits
pressure = pressure
windDir = wind_dir
windSpeed = wind_speed
UV = uv
And data doesn't seem to be flowing into Weewx. I guess I could start over
completely with my weewx config - this was previously running a
USB-connected Acurite. I was hoping I could comment that out and put this
in and it work.
On Tuesday, June 13, 2023 at 8:26:36 PM UTC-4 Jason Gibson wrote:
> Hi Rainer,
>
> Thanks for your reply.
>
> Rainfall data priority is set to piezo.
>
> Standalone interceptor driver output below:
>
> mapped packet: {'dateTime': 1686696648, 'usUnits': 1, 'pressure': 29.604,
> 'outHumidity': 85.0, 'inHumidity': 40.0, 'outTemp': 50.7, 'inTemp': 73.4,
> 'windSpeed': 8.5, 'windGust': 11.18, 'windDir': 279.0, 'radiation': 71.59,
> 'UV': 0.0}
>
> It seems that I had mapped the rain fields sort of correctly. Although I
> am not sure 'rain' and 'drain_piezo' are actually the same quantity. There
> does not appear to be an equivalent to the database field 'rain' in the
> output from the HP2560. It has only rain rate, daily, weekly, monthly and
> yearly rain totals. Not rain since last interval, which is my
> understanding of what the database fieldname 'rain' is meant to represent.
>
> Having looked at the wview-extended.py schema I can see that I had the
> wrong database field names for the battery values. I have since changed
> the mapping as seen below, still no rain or battery data.
>
> [[sensor_map_extensions]]
>
> rain = drain_piezo
> rainRate = rrain_piezo
> supplyVoltage = wh90batt
> referenceVoltage = ws90cap_volt
>
> Not sure where to go from here.
>
> Cheers,
>
> Jason
>
> On Wednesday, June 14, 2023 at 3:41:00 AM UTC+10 Rainer Lang wrote:
>
>> Hi Jason
>>
>> 1. the local API (local Ecowitt Gateway API aka GW1000 API) was never
>> implemented in the HP25x0, HP350x, WH2910 consoles => so no such thing like
>> depreciation
>> you want to know which console supports which API, look up
>> https://www.wxforum.net/index.php?topic=40730.0 😎
>>
>> 2. the reason why you may not receive WS90 (piezo rain) data via the
>> custom server could be that your WS90 has not been set in the console as
>> primary rain device.
>> gear wheel --> setup (more) --> rain priority (has to be set to piezo).
>>
>> 3. could you run the interceptor driver stand-alone and post here the
>> result of one console post ?
>> (or run weewx in debug = 3 mode and copy from the syslog)
>>
>> regards
>>
>> Rainer
>> On 13.06.2023 02:28, Jason Gibson wrote:
>>
>> Hi All,
>>
>> I have been trying to coax rain data out of the WS90 and into weewx.
>>
>> I assume that the local API is deprecated on the HP2560 as I can't appear
>> to get any details out of it on port 45000.
>>
>> I am currently using the interceptor driver in listen mode on port 8080.
>> And I am able to log all data in WeeWX except rain from the piezo sensor,
>> and battery voltages.
>>
>> I have tried mapping sensors to fields as below, to no avail, is anyone
>> able to assist with the interceptor driver, or is there another driver
>> better suited to my hardware?
>>
>> Hardware:
>> -----------------
>> HP2564 - HP2560 & WS90
>>
>> HP2560_C:
>> Hardware revision V2.0
>> Firmware: Pro_V1.9.0
>> EasyWeatherProv5.11
>> WS90:
>> Firmware 1.3.3
>>
>> weewx.conf extract:
>> --------------------------------
>>
>> driver = user.interceptor
>> device_type = ecowitt-client
>> port = 8080
>> iface = ens18
>> [[sensor_map_extensions]]
>> rain = drain_piezo
>> rainRate = rrain_piezo
>> bat_wind = wh90batt
>> bat_rain = ws90cap_volt
>>
>> Am I using the right field names? Example output from the ws90 is as
>> follows:
>>
>> PASSKEY: <redacted>
>> stationtype: EasyWeatherPro_V5.1.1
>> runtime: 2
>> dateutc: 2023-06-11 01:53:27
>> tempinf: 77.0
>> humidityin: 40
>> baromrelin: 30.224
>> baromabsin: 29.946
>> tempf: 61.2
>> humidity: 60
>> winddir: 12
>> windspeedmph: 5.14
>> windgustmph: 6.93
>> maxdailygust: 10.74
>> solarradiation: 270.64
>> uv: 2
>> rrain_piezo: 0.000
>> erain_piezo: 0.000
>> hrain_piezo: 0.000
>> drain_piezo: 0.000
>> wrain_piezo: 0.000
>> mrain_piezo: 1.209
>> yrain_piezo: 1.209
>> ws90cap_volt: 5.2
>> ws90_ver: 133
>> gain10_piezo: 1.15
>> gain20_piezo: 1.05
>> gain30_piezo: 1.00
>> gain40_piezo: 1.00
>> gain50_piezo: 1.00
>> wh90batt: 3.10
>> freq: 433M
>> model: HP2564CA_Pro_V1.9.0
>> interval: 30
>>
>> Cheers,
>>
>> Jason
>>
>> --
>> You received this message because you are subscribed to the Google Groups
>> "weewx-user" group.
>> To unsubscribe from this group and stop receiving emails from it, send an
>> email to [email protected].
>> To view this discussion on the web visit
>> https://groups.google.com/d/msgid/weewx-user/8828c0f2-f040-4558-bf6d-f2ff1dedb0ben%40googlegroups.com
>>
>> <https://groups.google.com/d/msgid/weewx-user/8828c0f2-f040-4558-bf6d-f2ff1dedb0ben%40googlegroups.com?utm_medium=email&utm_source=footer>
>> .
>>
>>
--
You received this message because you are subscribed to the Google Groups
"weewx-user" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion on the web visit
https://groups.google.com/d/msgid/weewx-user/6fae27f2-04ad-41e8-a3c5-390734694e4bn%40googlegroups.com.
