It is not working with StdCalibrate
[StdCalibrate]
[[Corrections]]
# For each type, an arbitrary calibration expression can be given.
# It should be in the units defined in the StdConvert section.
# Example:
foo = foo + 0.2
outHumidity = extraHumid1
I am getting correct values in extraHumid1 from replacement sensor. I
checked database. But outHumidity is stil getting value from dead station
sensor.
sreda, 8. november 2023 ob 11:14:14 UTC+1 je oseba [email protected]
napisala:
> I will try this one for now! I hope weewx will use it later to calculate
> dew point and heat index with this value.
>
> [StdCalibrate]
> [[Corrections]]
> outHumidity = extraHumid1 if extraHumid1 is not None else None
>
> torek, 7. november 2023 ob 12:36:26 UTC+1 je oseba [email protected]
> napisala:
>
>> Thanks, I forgot about that! Then I would definitely prefer getting an
>> Ecowitt Gateway + outdoor sensor over the replacement part.
>>
>> gjr80 schrieb am Montag, 6. November 2023 um 21:08:54 UTC+1:
>>
>>> Not necessary, if the Ecowitt gateway driver can be used it can be run
>>> as a data service to augment an existing driver.
>>>
>>> Gary
>>>
>>> On Tuesday, 7 November 2023 at 06:03:39 UTC+10 [email protected]
>>> wrote:
>>>
>>>> With the ecowitt gateway you need a second weewxd running, as a
>>>> downside. But you can build a whole new station, step by step, around that
>>>> gateway (which is probably way to go, sooner or later).
>>>>
>>>> vince schrieb am Montag, 6. November 2023 um 20:41:08 UTC+1:
>>>>
>>>>> Another option is an ecowitt gateway and their outside T+H sensor,
>>>>> which integrates well into weewx.
>>>>>
>>>>> On Monday, November 6, 2023 at 11:19:23 AM UTC-8 [email protected]
>>>>> wrote:
>>>>>
>>>>>> Do not use a BME280 as an outdoor Sensor, it is not suited for this
>>>>>> purpose. The operating range is only valid in non-condensing
>>>>>> environments.
>>>>>> In condensing environments, especially below freezing point, these
>>>>>> sensors
>>>>>> are proven unusable. Go for a SHT3x or SHT4x.
>>>>>>
>>>>>> Mark Fraser schrieb am Montag, 6. November 2023 um 18:32:59 UTC+1:
>>>>>>
>>>>>>> On 06/11/2023 08:18, [email protected] wrote:
>>>>>>> > Hello i have ws2300 station and my humidity sensor probably died.
>>>>>>> It
>>>>>>> > only shows values from 70 to 80% .I cannot get replacement part
>>>>>>> anywhere
>>>>>>> > because it is not in production anymore and I cannot buy whole new
>>>>>>> > station because it will be complicated to get all things up
>>>>>>> running again.
>>>>>>> >
>>>>>>> > I was thinking of getting external humidity sensor and hook it to
>>>>>>> > arduino board and then read humidity values remotely via crontabs
>>>>>>> in a
>>>>>>> > txt file. Is is somehow possible to "trick" weewx to read this
>>>>>>> value
>>>>>>> > instead of getting it from station because I am using weewx to
>>>>>>> calculate
>>>>>>> > heat index and dew point.
>>>>>>> Could you use something like BME280WX from here?
>>>>>>> https://gitlab.com/wjcarpenter/bme280wx
>>>>>>>
>>>>>>
--
You received this message because you are subscribed to the Google Groups
"weewx-user" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion on the web visit
https://groups.google.com/d/msgid/weewx-user/0d8984ab-6bb1-4380-8b05-3dc74b41134en%40googlegroups.com.
