Musa, I use SNMPView: - Right click on the device. If it is an SNMP managable device you will see SNMPView .... This interface will allow you to walk the MIB on the device. You can then select the object, then double click to see the OID. - Configure a SNMP monitor and use the OID. Joe In reply to 30 May message from [EMAIL PROTECTED]:
>Thanks very much for your advice !!!. I found out that the problem was on my Whatsup >Gold machine. The default gateway >had not been properly set. Now I can see the radios (Altium DMC) which use SNMP on >the maps. I also succeeded in setting >audio alerts when devices miss polls. In case of SMTP alerts how do get them to the >mail server which is on another LAN >from the one I'm working on? > > >I now want to monitor some parameters on these radios i.e RSSI-Radio Signal Strength >Indicator, BER-Bit Error Rate and >other alarms. I understand I have to set SNMP traps but how do I obtain the MIB >values for the parameters I need to >monitor. > >Thanking you in advance > >Musa > >-----Original Message----- >From: Kainz Michael [mailto:[EMAIL PROTECTED] Sent: Wednesday, May 28, 2003 5:16 PM >To: Musa Musazi >Subject: AW: [WhatsUp Forum] FW: [WhatsUp Gold 8] musazi musa [T20030522008C] > >I supose that these radios are on different subnets, > >Can you ping the radios from other machines on the same subnet of the WUG machine ? >If so first check routing on your WhatsUpGold machine. > >If not maybe your routers do not forward ICMP traffic, so check router config. >or default gateway settings in your radios are wrong. > >regards > >Michael > > -----Urspr�ngliche Nachricht----- > Von: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] > Gesendet: Mittwoch, 28. Mai 2003 16:04 > An: [EMAIL PROTECTED] > Cc: [EMAIL PROTECTED] > Betreff: [WhatsUp Forum] FW: [WhatsUp Gold 8] musazi musa [T20030522008C] > Wichtigkeit: Hoch > > > Good day, > > I am evaluating WhatsupGold 8. I made an ICMP scan on a LAN from my whatup Gold 8. > The radio addresses are in the same >range as the other devices The devices I get after the search are two routers, a >proxy server, a workstation and one >radio(altium). All these are on the same LAN as the Whatsup Gold machine > > However, there is a set of other radios in series beyond the one I see and another > set beyond each of the routers. All >these radios are not discovered by the scan. I verified by other means that these >radios were on at the time of the scan. >I can't even ping these radios from the WhatsupGold machine. > > Can anyone out there help me > > Regards > > Musazi musa > Transmission Planning Engineer > MTN Uganda > > > -----Original Message----- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] > Sent: Thursday, May 22, 2003 6:10 PM > To: Musa Musazi > Subject: RE: [WhatsUp Gold 8] musazi musa [T20030522008C] > > Hello, > > Are you evaluating WhatsUp Gold or do you have a fully purchased version? > Are the radio IP's in the same range as the other devices? Are the devices > that are not discovered on at the time of the scan? Can you ping these > devices from the WhatsUp Gold machine? > > > Regards, > > Martha Nguyen > WhatsUp Gold Technical Sales > Ipswitch, Inc > www.ipswitch.com > > > -----Original Message----- > Sender : [EMAIL PROTECTED] > Tracking Number : T20030522008CZ1900301 > Pool : WhatsUp + Gold Eval > Sent to : [EMAIL PROTECTED] > Date : 5/22/03 1:29 AM > --- > > Name: musazi musa > Address: [EMAIL PROTECTED] > Product: WhatsUp Gold 8 > OS: Windows 2000 > Problem: > > I connected whatsup gold to a LAN that has a radio network management > system. I used the create map wizard using ICMP for a specified range of IP > adress. However, the map contained only the workstations and routers > directly connected to the LAN. The radios(IP based Altium) in the field > where not seen. Where could the problem be. Can I send you the diagram of > the whole management system? > > > -- > > WhatsUp Gold Ask A Tech Version . (c) 2003 Ipswitch, Inc. > > > > > > This email and any files transmitted with it are confidential and intended solely > for the use of the individual or >entity to whom they are addressed. If you have received this email in error please >notify the network manager. This >message contains confidential information and is intended only for the individual >named. If you are not the named >addressee you should not disseminate, distribute or copy this e-mail. >This email and any files transmitted with it are confidential and intended solely for >the use of the individual or entity >to whom they are addressed. If you have received this email in error please notify >the network manager. This message >contains confidential information and is intended only for the individual named. If >you are not the named addressee you >should not disseminate, distribute or copy this e-mail. Please visit http://www.ipswitch.com/support/mailing-lists.html to be removed from this list. An Archive of this list is available at: http://www.mail-archive.com/whatsup_forum%40list.ipswitch.com/
