Hi Bill, This may (or may not) be of interest. Looking through the list of UDP status messages, I find an extra message (out of sequence?) that occurs at the end of a transmitting period. For example:
05:09:54: Dial: 14095600, Mode: WSPR-2, DX_Call: G4KLA, Report: -15, TX_Mode: WSPR-2, TX_Enabled: 1, Transmitting: 0 05:11:54: Dial: 18104460, Mode: WSPR-2, DX_Call: G4KLA, Report: -15, TX_Mode: WSPR-2, TX_Enabled: 1, Transmitting: 0 05:13:54: Dial: 21094600, Mode: WSPR-2, DX_Call: G4KLA, Report: -15, TX_Mode: WSPR-2, TX_Enabled: 1, Transmitting: 0 Changing freq for another RX period 05:14:00: Dial: 21094600, Mode: WSPR-2, DX_Call: G4KLA, Report: -15, TX_Mode: WSPR-2, TX_Enabled: 1, Transmitting: 1 Quick change of mind: TX instead of RX 05:15:53: Dial: 21094600, Mode: WSPR-2, DX_Call: G4KLA, Report: -15, TX_Mode: WSPR-2, TX_Enabled: 1, Transmitting: 0 End of transmission: so status message 05:15:53: Dial: 24924600, Mode: WSPR-2, DX_Call: G4KLA, Report: -15, TX_Mode: WSPR-2, TX_Enabled: 1, Transmitting: 0 Change of frequency for next RX period 05:15:53: Dial: 21094600, Mode: WSPR-2, DX_Call: G4KLA, Report: -15, TX_Mode: WSPR-2, TX_Enabled: 1, Transmitting: 0 Change back to previous frequency >>> this seems out of place 05:16:07: Dial: 24924600, Mode: WSPR-2, DX_Call: G4KLA, Report: -15, TX_Mode: WSPR-2, TX_Enabled: 1, Transmitting: 0 Re-think: change to new frequency >>> correction to fix this 05:17:54: Dial: 28124600, Mode: WSPR-2, DX_Call: G4KLA, Report: -15, TX_Mode: WSPR-2, TX_Enabled: 1, Transmitting: 0 Continue RX sequence without extra messages 05:19:54: Dial: 7038600, Mode: WSPR-2, DX_Call: G4KLA, Report: -15, TX_Mode: WSPR-2, TX_Enabled: 1, Transmitting: 0 17:55:54: Dial: 24924600, Mode: WSPR-2, DX_Call: G4KLA, Report: -15, TX_Mode: WSPR-2, TX_Enabled: 1, Transmitting: 0 17:57:54: Dial: 28124600, Mode: WSPR-2, DX_Call: G4KLA, Report: -15, TX_Mode: WSPR-2, TX_Enabled: 1, Transmitting: 0 17:59:54: Dial: 10138700, Mode: WSPR-2, DX_Call: G4KLA, Report: -15, TX_Mode: WSPR-2, TX_Enabled: 1, Transmitting: 0 But 7MHz should be next in RX lis. 18:00:00: Dial: 10138700, Mode: WSPR-2, DX_Call: G4KLA, Report: -15, TX_Mode: WSPR-2, TX_Enabled: 1, Transmitting: 1 18:01:53: Dial: 10138700, Mode: WSPR-2, DX_Call: G4KLA, Report: -15, TX_Mode: WSPR-2, TX_Enabled: 1, Transmitting: 0 18:01:53: Dial: 24924600, Mode: WSPR-2, DX_Call: G4KLA, Report: -15, TX_Mode: WSPR-2, TX_Enabled: 1, Transmitting: 0 18:01:53: Dial: 10138700, Mode: WSPR-2, DX_Call: G4KLA, Report: -15, TX_Mode: WSPR-2, TX_Enabled: 1, Transmitting: 0 Out of place?? 18:02:08: Dial: 24924600, Mode: WSPR-2, DX_Call: G4KLA, Report: -15, TX_Mode: WSPR-2, TX_Enabled: 1, Transmitting: 0 Expected 14Mhz next 18:03:54: Dial: 7038600, Mode: WSPR-2, DX_Call: G4KLA, Report: -15, TX_Mode: WSPR-2, TX_Enabled: 1, Transmitting: 0 Start next RX run correctly with 7Mhz, 10, 14, 18 etc 18:07:54: Dial: 10138700, Mode: WSPR-2, DX_Call: G4KLA, Report: -15, TX_Mode: WSPR-2, TX_Enabled: 1, Transmitting: 0 18:09:54: Dial: 14095600, Mode: WSPR-2, DX_Call: G4KLA, Report: -15, TX_Mode: WSPR-2, TX_Enabled: 1, Transmitting: 0 18:11:54: Dial: 18104460, Mode: WSPR-2, DX_Call: G4KLA, Report: -15, TX_Mode: WSPR-2, TX_Enabled: 1, Transmitting: 0 Sequence of 7, 10, 14, 18, 21, 24, 28 is not always followed. I thought coordinated sequential was in force? --- John G4KLA ------------------------------------------------------------------------------ _______________________________________________ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/wsjt-devel
