Hi Mike,
The trace is here:
https://dl.dropboxusercontent.com/u/33211132/WSJT-X_trace_6.log
<https://dl.dropboxusercontent.com/u/33211132/WSJT-X_trace_6.log>
This is your patch running on top of r5700. Bill’s patch has not been installed.
There are two complete sessions in the trace file. In each case, I started the
program and immediately pressed Tx Enable. Bandhopping is enabled. If we define
0:00 to be the start of the first full receive cycle, then at some time near
1:54 the Tx Enable button goes from red to white. Further, the rig and the
program fail to hop, i.e. the rig fails to hop to a new frequency.
The error events can be found in the log at 22:41:54 and 22:47:54.
I’lll note that there is always a long string of errors produced during the
shutdown phase after I use Quit to end the program. The trace file includes
two examples of this as well.
Steve k9an
> On Jul 10, 2015, at 9:13 PM, Michael Black <mdblac...@gmail.com> wrote:
>
> Can you send a trace log? I can't imagine how this one line could cause any
> problems.
>
> From: Steven Franke [mailto:s.j.fra...@icloud.com
> <mailto:s.j.fra...@icloud.com>]
> Sent: Friday, July 10, 2015 2:56 PM
> To: WSJT software development
> Subject: Re: [wsjt-devel] FW: r5700
>
> I should have said “on a clean r5700…”.
>
>> On Jul 10, 2015, at 7:52 PM, Steven Franke <s.j.fra...@icloud.com
>> <mailto:s.j.fra...@icloud.com>> wrote:
>>
>> Mike,
>>
>> I just tried your patch on a clean r5712. I never got to the transmit phase,
>> as I now get a critical hamlib error at 1:54 at the end of the receive
>> cycle, which kills Tx Enable… Once Tx Enable is disabled by the error, I
>> cannot be re-enabled. I did not do a detailed trace, but the bottom line is
>> that this is not solution.
>>
>> Steve
>>
>>
>>> On Jul 10, 2015, at 3:10 PM, Michael Black <mdblac...@gmail.com
>>> <mailto:mdblac...@gmail.com>> wrote:
>>>
>>> OK…this WSPR patch is a hack…but I believe this will solve the TS-480
>>> problem. The real solution is to only call WSPR_scheduling once instead of
>>> twice and only do it after ptt is turned off.
>>> For this hack simply ensure ptt=false before calling WSPR_scheduling.
>>> This should at least confirm that this is the problem being experienced on
>>> rigs that can't change frequency while transmitting.
>>>
>>> In mainwindow.cpp
>>>
>>> @@ -1858,6 +1863,7 @@
>>> m_btxok=false;
>>> }
>>> if(m_ntr) {
>>> + Q_EMIT m_config.transceiver_ptt (false); //Lower PTT just in
>>> case we're transmitting
>>> WSPR_scheduling ();
>>> m_ntr=0; //This WSPR Rx sequence is
>>> complete
>>> }
>>>
>>> 73
>>> Mike W9MDB
>>> ------------------------------------------------------------------------------
>>> Don't Limit Your Business. Reach for the Cloud.
>>> GigeNET's Cloud Solutions provide you with the tools and support that
>>> you need to offload your IT needs and focus on growing your business.
>>> Configured For All Businesses. Start Your Cloud Today.
>>> https://www.gigenetcloud.com/_______________________________________________
>>>
>>> <https://www.gigenetcloud.com/_______________________________________________>
>>> wsjt-devel mailing list
>>> wsjt-devel@lists.sourceforge.net <mailto:wsjt-devel@lists.sourceforge.net>
>>> https://lists.sourceforge.net/lists/listinfo/wsjt-devel
>>> <https://lists.sourceforge.net/lists/listinfo/wsjt-devel>
>>
>> ------------------------------------------------------------------------------
>> Don't Limit Your Business. Reach for the Cloud.
>> GigeNET's Cloud Solutions provide you with the tools and support that
>> you need to offload your IT needs and focus on growing your business.
>> Configured For All Businesses. Start Your Cloud Today.
>> https://www.gigenetcloud.com/_______________________________________________
>> <https://www.gigenetcloud.com/_______________________________________________>
>> wsjt-devel mailing list
>> wsjt-devel@lists.sourceforge.net <mailto:wsjt-devel@lists.sourceforge.net>
>> https://lists.sourceforge.net/lists/listinfo/wsjt-devel
>> <https://lists.sourceforge.net/lists/listinfo/wsjt-devel>
>
> ------------------------------------------------------------------------------
> Don't Limit Your Business. Reach for the Cloud.
> GigeNET's Cloud Solutions provide you with the tools and support that
> you need to offload your IT needs and focus on growing your business.
> Configured For All Businesses. Start Your Cloud Today.
> https://www.gigenetcloud.com/_______________________________________________
> <https://www.gigenetcloud.com/_______________________________________________>
> wsjt-devel mailing list
> wsjt-devel@lists.sourceforge.net <mailto:wsjt-devel@lists.sourceforge.net>
> https://lists.sourceforge.net/lists/listinfo/wsjt-devel
> <https://lists.sourceforge.net/lists/listinfo/wsjt-devel>
------------------------------------------------------------------------------
Don't Limit Your Business. Reach for the Cloud.
GigeNET's Cloud Solutions provide you with the tools and support that
you need to offload your IT needs and focus on growing your business.
Configured For All Businesses. Start Your Cloud Today.
https://www.gigenetcloud.com/
_______________________________________________
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
