Hello,
 following suggestions from others on this list I have tried to use freqcal
from WSJT-X 1.9.0-rc3 on a single GPS locked VHF beacon.

This beacon on 144.450 (VK5VF) runs a mixture of carrier and CW ID (on off
keying).  Each time I run the process that is outlined in the documentation
when I select the "solve for calibration"  I end up with the quite
unhelpful error telling me: "Calibration error  Check fmt.all for possible
bad data" so I dutifully look in this file to try and identify what is
wrong (sample below)

21:34:34 144450  1  1500  1368.324  -131.676   14.5   39.8
21:34:36 144450  1  1500  1369.671  -130.329   14.9   38.5
21:34:39 144450  1  1500  1369.555  -130.445   14.8   40.1
21:34:41 144450  1  1500  1368.284  -131.716   17.2   34.2
21:34:44 144450  1  1500  1368.318  -131.682   16.5   36.1
21:35:34 144450  1  1500  1369.171  -130.829   15.9   38.1
21:35:36 144450  1  1500  1369.574  -130.426   14.9   39.5
21:35:39 144450  1  1500  1369.270  -130.730   15.8   36.2
21:35:41 144450  1  1500  1370.659  -129.341   15.4   36.1
21:35:43 144450  1  1500  1372.416  -127.584   14.9   38.3
21:35:49 144450  1  1500  1371.663  -128.337   14.8   39.2
21:36:19 144450  1  1500  1373.065  -126.935   14.7   41.5
21:36:21 144450  1  1500  1372.527  -127.473   15.7   35.2
21:36:24 144450  1  1500  1372.356  -127.644   19.3   28.5
21:36:26 144450  1  1500  1372.464  -127.536   20.3   26.5
21:36:28 144450  1  1500  1372.826  -127.174   19.7   28.8
21:36:34 144450  1  1500  1370.782  -129.218   14.8   40.4
21:36:36 144450  1  1500  1370.859  -129.141   14.9   38.2
21:36:39 144450  1  1500  1371.701  -128.299   14.7   41.4
21:36:41 144450  1  1500  1371.060  -128.940   16.1   37.6
21:36:43 144450  1  1500  1371.607  -128.393   14.8   39.4
21:36:49 144450  1  1500  1373.245  -126.755   14.8   38.1

Can any of the list members help me identify which of these lines of data
would be in error?  Is the variance in offset too high as it goes from,
-126 to -131 Hz across the 30 second period,  When I try a smaller sample I
get the error telling me there is not enough information in the file, so
that did not help,

Regards,
Peter, vk5pj
------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, Slashdot.org! http://sdm.link/slashdot
_______________________________________________
wsjt-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/wsjt-devel

Reply via email to