If putty sees that, then it's not KISS. That looks like normal TNC ASCII output, not KISS.
On Mon, Feb 8, 2021 at 11:16 AM Eric Chamberlain <[email protected]> wrote: > > The code hangs at this line, so the mutex is opened. > port_data[port].channel = open(port_data[port].device_name, O_RDWR|O_NOCTTY); > > Jason, I think its in KISS. Regarding the readable payload with binary > garbage, I'm getting it. Here's some of what putty sees, so I think the baud > rate is good too. > KC3OBB-1>APT314,WIDE1-1,WIDE2-1:>MT-Omega v1.47 > KC3OBB-1>APT314,WIDE1-1,WIDE2-1:$GPRMC,190857,A,4015.8900,N,07946.0796,W,000,057,080221,,*03/TT3 > ROCKET|!"#c'6|!w!x! > KC3OBB-1>APT314,WIDE1-1,WIDE2-1:$GPRMC,190958,A,4015.8927,N,07946.0753,W,000,169,080221,,*0D|!##c':|!w:Q! > KC3OBB-1>APT314,WIDE1-1,WIDE2-1:$GPRMC,191059,A,4015.8942,N,07946.0762,W,000,169,080221,,*05|!$#c'<|!wGY! > KC3OBB-1>APT314,WIDE1-1,WIDE2-1:$GPRMC,191159,A,4015.8922,N,07946.0766,W,000,169,080221,,*06|!%#c'>|!w5]! > KC3OBB-1>APT314,WIDE1-1,WIDE2-1:$GPRMC,191300,A,4015.8922,N,07946.0776,W,000,169,080221,,*09/TT3 > ROCKET|!&#c'?|!w5f! > KC3OBB-1>APT314,WIDE1-1,WIDE2-1:$GPRMC,191401,A,4015.8930,N,07946.0789,W,000,169,080221,,*0C|!'#c'@|!w<r! > > > > > > From: "Jason KG4WSV" <[email protected]> > > Are you sure it’s in KISS mode? > > That would equate to a bunch of binary garbage for the packet headers plus > some readable text that’s the payload. > > And maybe triple check the baud rate? > > -Jason > > > > On Feb 8, 2021, at 6:30 AM, Eric Chamberlain <[email protected]> > > wrote: > > > > That certainly prevents the port from blocking. The interface in xastir > > returns as 'up' but it doesn't appear to be reading packets off the TNC in > > the view-incoming data window. Looking in putty it still shows the incoming > > packets. So its not quite fixed yet. > > > > > > > > > > From: "Jason KG4WSV" <[email protected]> > > > > Try the /dev/cu.whatever device special file. > > > > It’s been a few years but when I hit the same problem (well, Kermit not > > putty) switching to cu did the trick. > > > > -Jason > > > >> On Feb 7, 2021, at 8:44 PM, Eric Chamberlain <[email protected]> > >> wrote: > >> > >> I've been trying to configure an interface to read the tinytrak4 TNC, > >> which is supposed to operate as KISS according to their docs. When I run > >> PuTTY on the /dev/tty.usbserial-1430 port I can see packets coming in from > >> a test transmitter. I close putty and open xastir so the port isn't > >> blocking. When I go to start the TNC interface, in mac it hangs without > >> messages in the terminal window. On the putty it doesn't hang but there's > >> nothing. There are never incoming packets from the view data window. > >> Unfortunately, Byonics say they don't know much about xastir. I've tried > >> this both on my mac and my raspberry. The cable setup works for > >> programming and PuTTY, so I don't think its that or drivers. I think it > >> comes down to settings. Is there anything I can try? > >> _______________________________________________ > >> Xastir mailing list > >> [email protected] > >> http://xastir.org/mailman/listinfo/xastir > > _______________________________________________ > > Xastir mailing list > > [email protected] > > http://xastir.org/mailman/listinfo/xastir[http://xastir.org/mailman/listinfo/xastir][http://xastir.org/mailman/listinfo/xastir[http://xastir.org/mailman/listinfo/xastir]] > > _______________________________________________ > > Xastir mailing list > > [email protected] > > http://xastir.org/mailman/listinfo/xastir[http://xastir.org/mailman/listinfo/xastir] > _______________________________________________ > Xastir mailing list > [email protected] > http://xastir.org/mailman/listinfo/xastir[http://xastir.org/mailman/listinfo/xastir] > _______________________________________________ > Xastir mailing list > [email protected] > http://xastir.org/mailman/listinfo/xastir -- Curt, WE7U http://xastir.org http://www.sarguydigital.com _______________________________________________ Xastir mailing list [email protected] http://xastir.org/mailman/listinfo/xastir
