Hi Arif,
I've created the partition file as below and set the parameter
partitionfile with chdef.
############
#XCAT_PARTITION_START#
part /boot --fstype=ext4 --size=256 --ondisk md127
part / --fstype=ext4 --size=86947 --ondisk md127
part swap --size=16384 --ondisk md127
##XCAT_PARTITION_END#
############
However I'm still getting the same error message:
############
Running anaconda 13.21.215, the CentOS system installer - please wait.
Examining storage devices
In progress
Examining storage devices
In progress
Could not allocate requested partitions:
not enough free space on disks.
Press 'OK' to exit the installer.
terminating anaconda...done
############
Do you have any tip?
Thanks in advance!
Fabio Souza
2014-10-15 14:32 GMT-03:00 Arif Ali <[email protected]>:
> On 15/10/14 18:06, Fabio Moreira wrote:
> >
> > Hi,
> >
> > I'm facing a problem while installing a server with an onboard Intel
> > SATA controller (*SATA controller: Intel Corporation C600/X79 series
> > chipset 6-Port SATA AHCI Controller (rev 06)*) when configured with
> > RAID1 through this controller (Hardware RAID). This controller sets
> > the RAID disks as /dev/md127 and the partitions as /dev/md127p1,
> > /dev/md127p2 and /dev/md127p3 for instance.
> >
> > Since the devices are not the standard /dev/sdX, I'm not able to
> > install. Is there any hint?
> >
> > Thanks in advance!
> >
> > Fabio Souza
> Hi Fabio,
>
> It depends on the template you are using, you can customise this however
> you want. By default it will use sd* device, But you can specify your
> own partition file with the osimage, for example for redhat based
> machines I tend to do, the below, with filename such as
> /install/templates/compute/compute.partfile, and then can specify the
> partition file as "chdef -t osimage my-osimage
> partitionfile=/install/templates/compute/compute.partfile". In my
> instance I have not specified the disk, but you should easily be able to
> use the "--ondisk=" paramater for any of the part commands in the
> kickstart file.
>
> #############
> part /boot --fstype=ext4 --size=1024
> part /boot/efi --fstype=vfat --size=100
> part pv.1 --grow --size=1
>
> volgroup system --pesize=4096 pv.1
>
> logvol / --fstype=ext4 --name=root --vgname=system --size=20480
> logvol swap --name=swap --vgname=system --size=8192
> logvol /var --fstype=ext4 --name=var --vgname=system --size=40960
> #############
>
> I hope that makes sense
>
> Arif Ali
>
> IRC: arif-ali at freenode
> LinkedIn: http://uk.linkedin.com/in/arifali
>
>
>
> ------------------------------------------------------------------------------
> Comprehensive Server Monitoring with Site24x7.
> Monitor 10 servers for $9/Month.
> Get alerted through email, SMS, voice calls or mobile push notifications.
> Take corrective actions from your mobile device.
> http://p.sf.net/sfu/Zoho
> _______________________________________________
> xCAT-user mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/xcat-user
>
--
Fábio MS
------------------------------------------------------------------------------
Comprehensive Server Monitoring with Site24x7.
Monitor 10 servers for $9/Month.
Get alerted through email, SMS, voice calls or mobile push notifications.
Take corrective actions from your mobile device.
http://p.sf.net/sfu/Zoho
_______________________________________________
xCAT-user mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/xcat-user