it turns out it was a bad eth cable. when watching console i see eth timing
out so i replaced the cable and it worked.
thanks,
damir
On Wed, Jan 13, 2016 at 12:32 AM Xiao Peng Wang <[email protected]> wrote:
> From symptom looks like your eth0 booted from dhcp and it faild to get ip
> from dhcpd. You may find dhcp failed log when this issue happens.
>
> Thanks
> Best Regards
> ----------------------------------------------------------------------
> Wang Xiaopeng (王晓朋)
> IBM China System Technology Laboratory
> Tel: 86-10-82453455
> Email: [email protected]
> Address: 28,ZhongGuanCun Software Park,No.8 Dong Bei Wang West Road,
> Haidian District Beijing P.R.China 100193
>
>
>
> ----- Original message -----
> From: Damir Krstic <[email protected]>
> To: xCAT Users Mailing list <[email protected]>
>
> Cc:
> Subject: Re: [xcat-user] issue when installing node
> Date: Wed, Jan 13, 2016 9:09 AM
>
> Yes all deployed from single management using commands like: nodeadd
> gpu[1-6] same thing for makehosts and makedns. That's why it's so weird and
> confusing that only one mode is having this issue.
>
> Before I left work today I redeployed this mode using our compute
> stateless image and that worked ok. Mode got the right name and eth
> started. Not sure what else to check. I am suspecting dhcp issue at this
> time but cannot be sure.
> On Tue, Jan 12, 2016 at 16:17 Casandra H Qiu <[email protected]> wrote:
>
> are all the 6 nodes defined on the same MN? check if the failed node
> defined in the /etc/hosts. make sure you ran makedns and makedhcp and
> compare node definition use lsdef command.
>
>
> Thanks,
> Casandra
> ...................................................................
> Casandra Hong Qiu
> Phone: (845) 433-9291, t/l 293-9291
> Office: B/002, Floor 3, Z13
> [email protected]
>
>
>
> [image: Inactive hide details for Damir Krstic ---01/12/2016 04:37:37
> PM---Hi, When installing new batch of GPU nodes via xCAT I've ran]Damir
> Krstic ---01/12/2016 04:37:37 PM---Hi, When installing new batch of GPU
> nodes via xCAT I've ran into an issue I
>
> From: Damir Krstic <[email protected]>
> To: xCAT Users Mailing list <[email protected]>
> Date: 01/12/2016 04:37 PM
> Subject: [xcat-user] issue when installing node
> ------------------------------
>
>
>
>
>
>
> Hi,
>
> When installing new batch of GPU nodes via xCAT I've ran into an issue I
> have not seen before. Out of 6 NextScale nx360m4 nodes with k80 GPUs all
> installed OK (nodeset <nodename> osimage=gpu6.6) except one.
>
> Symptoms of the issue: node installs OK (watching it via rcons/wcons) but
> on the reboot eth0 does not come up and hostname is set to
> localhost.localdomain
>
> Has anyone seen this issue before?
>
> Thanks,
>
> Damir
> ------------------------------------------------------------------------------
> Site24x7 APM Insight: Get Deep Visibility into Application Performance
> APM + Mobile APM + RUM: Monitor 3 App instances at just $35/Month
> Monitor end-to-end web transactions and take corrective actions now
> Troubleshoot faster and improve end-user experience. Signup Now!
> http://pubads.g.doubleclick.net/gampad/clk?id=267308311&iu=/4140
> _______________________________________________
> xCAT-user mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/xcat-user
>
>
>
> ------------------------------------------------------------------------------
> Site24x7 APM Insight: Get Deep Visibility into Application Performance
> APM + Mobile APM + RUM: Monitor 3 App instances at just $35/Month
> Monitor end-to-end web transactions and take corrective actions now
> Troubleshoot faster and improve end-user experience. Signup Now!
> http://pubads.g.doubleclick.net/gampad/clk?id=267308311&iu=/4140
> _______________________________________________
> xCAT-user mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/xcat-user
>
> [image: graycol.gif][image: graycol.gif]
>
>
> ------------------------------------------------------------------------------
> Site24x7 APM Insight: Get Deep Visibility into Application Performance
> APM + Mobile APM + RUM: Monitor 3 App instances at just $35/Month
> Monitor end-to-end web transactions and take corrective actions now
> Troubleshoot faster and improve end-user experience. Signup Now!
> http://pubads.g.doubleclick.net/gampad/clk?id=267308311&iu=/4140
> _______________________________________________
> xCAT-user mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/xcat-user
>
>
>
> ------------------------------------------------------------------------------
> Site24x7 APM Insight: Get Deep Visibility into Application Performance
> APM + Mobile APM + RUM: Monitor 3 App instances at just $35/Month
> Monitor end-to-end web transactions and take corrective actions now
> Troubleshoot faster and improve end-user experience. Signup Now!
> http://pubads.g.doubleclick.net/gampad/clk?id=267308311&iu=/4140
> _______________________________________________
> xCAT-user mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/xcat-user
>
------------------------------------------------------------------------------
Site24x7 APM Insight: Get Deep Visibility into Application Performance
APM + Mobile APM + RUM: Monitor 3 App instances at just $35/Month
Monitor end-to-end web transactions and take corrective actions now
Troubleshoot faster and improve end-user experience. Signup Now!
http://pubads.g.doubleclick.net/gampad/clk?id=267308311&iu=/4140
_______________________________________________
xCAT-user mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/xcat-user
