Hi, 2011/9/30 Fernando Herrero Carrón <[email protected]>: > Dear list, > > I am testing Xenomai 2.6.0-rc4 on a 2.6.38.8 linux kernel. I have two cards, > one NI 6713 for AO and one NI 6143 for AI. I use the analogy_ni_pcimio for > both, and it loads well. I can run the config program succesfully too. > > If I remove the devices using 'analogy_config -r ...', then unload the > modules with: > > rmmod analogy_ni_pcimio analogy_ni_mio analogy_ni_tio analogy_8255 > analogy_ni_mite xeno_analogy > > then load them again and try to reconfigure, I get the following error on > dmesg (I include the boot messages and the execution of a "cmd_read"): > > [ 55.735198] Analogy: analogy_ni_pcimio: pcimio_attach: found pci-6713 > board > [ 55.735246] Analogy: analogy_ni_pcimio: pcimio_attach: found irq 21 > [ 60.143227] Analogy: analogy_ni_pcimio: pcimio_attach: found pci-6143 > board > [ 60.143274] Analogy: analogy_ni_pcimio: pcimio_attach: found irq 20 > [ 79.772511] Analogy: a4l_ioctl_cancel: no acquisition to cancel on this > context > [ 79.772517] Analogy: analogy_ni_pcimio: ni_ai_cmd: start > [ 79.772525] Analogy: analogy_ni_pcimio: ni_ai_cmd: > Interrupt_A_Enable_Register = 0x0021 > [ 79.772531] Analogy: analogy_ni_pcimio: ni_ai_cmd: exit > [ 80.572613] Analogy: analogy_ni_pcimio: ni_mio_common: interrupt: > a_status=90f0 ai_mite_status=00200000 > [ 80.572616] Analogy: analogy_ni_pcimio: ni_mio_common: SC_TC interrupt > [ 236.290044] Analogy: MITE: Available NI device IDs: 0x1870 0x70c0 > [ 246.113821] Analogy: analogy_ni_pcimio: pcimio_attach: found pci-6143 > board > [ 246.113872] Analogy: analogy_ni_pcimio: pcimio_attach: found irq 20 > [ 246.113876] Analogy: analogy_ni_pcimio: pcimio_attach: irq not available > [ 246.113879] Analogy: a4l_request_irq: IRQ registration failed > [ 251.563782] Analogy: analogy_ni_pcimio: pcimio_attach: found pci-6713 > board > [ 251.563824] Analogy: analogy_ni_pcimio: pcimio_attach: found irq 21 > [ 251.563828] Analogy: analogy_ni_pcimio: pcimio_attach: irq not available > [ 251.563830] Analogy: a4l_request_irq: IRQ registration failed > > BTW, the analogy_config program does not report those errors. > > This is bothering because I'm fiddling with the drivers and everytime I > change something I have to reboot. Anyone experiencing the same problem?
Sorry. I will try to fix that as soon as possible. > > Thanks for your help, > Fernando > > _______________________________________________ > Xenomai-help mailing list > [email protected] > https://mail.gna.org/listinfo/xenomai-help > > Alexis. _______________________________________________ Xenomai-help mailing list [email protected] https://mail.gna.org/listinfo/xenomai-help
