Hallo! It almost works now. I really do get two screens :0.0 and :0.1 - I can start a 2nd WM on :0.1 and xrandr really knows only about LVDS.
BUT the image on the LVDS is completely blank. My Xorg.0.log ist here: http://paste.debian.net/14304/ The config is unchanged but for the ConnectorTable (for which I did not find any explaination yet) option. Saluti! Ludwig Alex Deucher wrote: > On Fri, Aug 8, 2008 at 6:53 AM, Ludwig Meyerhoff <[EMAIL PROTECTED]> wrote: >> Hallo! >> >> I am trying to (re-) setup Zaphod-mode one more time. >> After I found the device-sctions had the same identifier, I am back to >> the original problem: LVDS is off, image only on the 2nd head. >> >> There is a panel connected at the LVDS port, and there is one at the >> VGA-0 port. The notebook only has one more S-Video connector. >> >> The setup is as follows: >> (==) ServerLayout "Default Layout" >> (**) |-->Screen "Default Screen" (0) >> (**) | |-->Monitor "Generic Monitor 0" >> (**) | |-->Device "ATI Technologies Inc Radeon RV200 LX [Mobility FireGL >> 7800 M7] 0" >> (**) |-->Screen "External Screen" (1) >> (**) | |-->Monitor "Generic Monitor 1" >> (**) | |-->Device "ATI Technologies Inc Radeon RV200 LX [Mobility FireGL >> 7800 M7] 1" >> > > <snip> > >> (II) RADEON(0): Port0: >> Monitor -- AUTO >> Connector -- DVI-D >> DAC Type -- None >> TMDS Type -- Internal >> DDC Type -- 0x64 > > this instance of the driver is getting the DVI port. > > >> (II) RADEON(1): Port0: >> Monitor -- AUTO >> Connector -- VGA >> DAC Type -- Primary >> TMDS Type -- None >> DDC Type -- 0x60 > > > > and this instance is getting VGA. > >> And I do not get a second screen: >> [EMAIL PROTECTED]:~$ DISPLAY=":0.1" icewm-gnome >> IceWM: using /home/ludwig/.icewm for private configuration files >> IceWM: Can't open display: :0.1. X must be running and $DISPLAY set. >> [EMAIL PROTECTED]:~$ >> >> >> The module I run has the following version: >> (II) LoadModule: "ati" >> (II) Loading /usr/lib/xorg/modules/drivers//ati_drv.so >> (II) Module ati: vendor="X.Org Foundation" >> compiled for 1.4.2, module version = 6.9.0 >> Module class: X.Org Video Driver >> ABI class: X.Org Video Driver, version 2.0 >> (II) LoadModule: "radeon" >> (II) Loading /usr/lib/xorg/modules/drivers//radeon_drv.so >> (II) Module radeon: vendor="X.Org Foundation" >> compiled for 1.4.2, module version = 4.3.0 >> Module class: X.Org Video Driver >> ABI class: X.Org Video Driver, version 2.0 >> >> >> There is no difference if I set up "ati" or "readeon" driver directly in the >> xorg.conf. >> > > ati is just a wrapper. it loads radeon or r128 or mach64 depending on > what chip you have, so it doesn't matter which one you have. > >> >> Any hint, what to do? > > In your case, since you system has LVDS, DVI, and VGA, it's ending up > with DVI and VGA for each zaphod head. You'll have to force the > connector table to get this to work. If you want to use LVDS and VGA, > add this option to each device section: > > Option "ConnectorTable" "0,0,0,7,96,1,0,1" > > Alex _______________________________________________ xorg-driver-ati mailing list [email protected] http://lists.x.org/mailman/listinfo/xorg-driver-ati
