My zd1211 is hanging my machine when waking up from suspend until I pull the device out. Should the firmware be reloaded when waking from a suspend?
[12245.012000] PM: Writing back config space on device 0000:00:1d.7 at offset f (was 400, writing 405) [12253.456000] usb_endpoint usbdev5.5_ep00: PM: resume from 0, parent 5-4.5 still 2 [12253.456000] usb_device usbdev5.5: PM: resume from 0, parent 5-4.5 still 2 [12253.456000] usb_endpoint usbdev5.5_ep01: PM: resume from 0, parent 5-4.5:1.0 still 2 [12253.456000] usb_endpoint usbdev5.5_ep82: PM: resume from 0, parent 5-4.5:1.0 still 2 [12253.456000] usb_endpoint usbdev5.5_ep83: PM: resume from 0, parent 5-4.5:1.0 still 2 [12253.456000] usb_endpoint usbdev5.5_ep04: PM: resume from 0, parent 5-4.5:1.0 still 2 [12254.540000] e1000: 0000:02:0c.0: e1000_probe: (PCI:33MHz:32-bit) 00:07:e9:55:4b:7e [12254.544000] usb 1-2.1: new low speed USB device using uhci_hcd and address 8 [12254.576000] PM: Adding info for No Bus:eth0 [12254.576000] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection [12254.592000] ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 17 (level, low) -> IRQ 20 [12255.404000] usb 5-4.5: print_id() 0ace:1215 v4810 high [12255.480000] usb 5-4.5: reset high speed USB device using ehci_hcd and address 5 [12255.572000] usb 5-4.5: request_fw_file() fw name zd1211/zd1211b_ub [12255.572000] PM: Adding info for No Bus:5-4.5 [12255.624000] PM: Removing info for No Bus:5-4.5 [12255.624000] usb 5-4.5: upload_firmware() firmware device id 0x4810 is equal to the actual device id [12255.624000] usb 5-4.5: request_fw_file() fw name zd1211/zd1211b_uphr [12255.628000] PM: Adding info for No Bus:5-4.5 [12255.636000] PM: Removing info for No Bus:5-4.5 [12255.636000] usb 5-4.5: upload_code() transfer size 4096 [12255.644000] usb 5-4.5: upload_code() transfer size 1024 [12255.648000] usb 5-4.5: upload_code() firmware confirm return value 0x01 [12260.648000] zd1211rw_mac80211 5-4.5:1.0: probe() couldn't reset configuration. Error number -110 [12260.720000] usb 5-4.5: reset high speed USB device using ehci_hcd and address 5 [12275.792000] usb 5-4.5: device descriptor read/64, error -110 [12290.968000] usb 5-4.5: device descriptor read/64, error -110 [12291.144000] usb 5-4.5: reset high speed USB device using ehci_hcd and address 5 [12298.460000] zd1211rw_mac80211: probe of 5-4.5:1.0 failed with error -110 [12298.460000] usb 5-4.5: USB disconnect, address 5 -- Jon Smirl [EMAIL PROTECTED] ------------------------------------------------------------------------- This SF.net email is sponsored by DB2 Express Download DB2 Express C - the FREE version of DB2 express and take control of your XML. No limits. Just data. Click to get it now. http://sourceforge.net/powerbar/db2/ _______________________________________________ Zd1211-devs mailing list - http://zd1211.wiki.sourceforge.net/ Unsubscribe: https://lists.sourceforge.net/lists/listinfo/zd1211-devs