Hi daniel,
I had tried to use the vendor driver and it worked with zd1211b.
So i modify the line in the kernel:
{ USB_DEVICE(0x0cde, 0x001a), .driver_info = DEVICE_ZD1211B }
and it has worked fine also in monitor mode.
I saw the vendor kernel say (during the boot) :
kernel: [ 1298.836000] Finsih download Firmware. Ready to reboot
kernel: [ 1298.836000] zd1211:FIRMWARE_CONFIRM = 1
kernel: [ 1298.836000] zd1211:USB Download Boot code success
Perhaps the vendor dirver unlock some firmware lock ???
Otherwise it has worked fine also in monitor mode.
tanks and bye
----- Original Message -----
From: "Daniel Drake" <[EMAIL PROTECTED]>
To: "Giuseppe Lippolis" <[EMAIL PROTECTED]>
Cc: <zd1211-devs@lists.sourceforge.net>
Sent: Thursday, July 12, 2007 1:03 AM
Subject: Re: [zd1211-devs] problems on device 0cde:001a
> Giuseppe Lippolis wrote:
>> 00:37:02 kernel: [ 502.652000] SoftMAC: Sent Authentication Request to
>> 00:0f:3d:a6:fa:da.
>> 00:37:02 kernel: [ 502.656000] SoftMAC: Open Authentication completed
>> with 00:0f:3d:a6:fa:da
>> 00:37:02 kernel: [ 502.656000] zd1211rw 4-1:1.0: set_channel() channel 1
>> 00:37:02 kernel: [ 502.656000] zd1211rw 4-1:1.0: zd_chip_lock_phy_regs()
>> CR_REG1: 0xa0 -> 0x20
>> 00:37:02 kernel: [ 502.656000] zd1211rw 4-1:1.0: zd_rf_set_channel()
>> channel: 1
>> 00:37:02 kernel: [ 502.656000] zd1211rw 4-1:1.0: zd_usb_rfwrite() value
>> 0x003f790 bits 24
>> 00:37:02 kernel: [ 502.660000] zd1211rw 4-1:1.0: zd_usb_rfwrite() value
>> 0x0033331 bits 24
>> 00:37:02 kernel: [ 502.660000] zd1211rw 4-1:1.0: zd_usb_rfwrite() value
>> 0x000000d bits 24
>> 00:37:02 kernel: [ 502.664000] zd1211rw 4-1:1.0: update_pwr_int()
>> channel 1 pwr_int 0x53
>> 00:37:02 kernel: [ 502.664000] zd1211rw 4-1:1.0: patch_cck_gain()
>> patching value 1c
>> 00:37:02 kernel: [ 502.668000] zd1211rw 4-1:1.0:
>> zd_chip_unlock_phy_regs() CR_REG1: 0x20 -> 0xa0
>> 00:37:02 kernel: [ 502.668000] SoftMAC: sent association request!
>> 00:37:02 kernel: [ 502.672000] usb 4-1: handle_retry_failed_int() retry
>> failed interrupt
>> 00:37:06 kernel: [ 506.612000] zd1211rw 4-1:1.0: zd_mac_get_channel()
>> channel 1
>> 00:37:06 kernel: [ 506.612000] zd1211rw 4-1:1.0: iw_get_range()
>> 00:37:07 kernel: [ 507.668000] SoftMAC: assoc request timed out!
>
> Authentication completes (so zd1211 TX must be working) but association
> times out.
>
> Does the vendor driver work with this device?
>
> Do you have other wireless hardware that you could put in monitor mode, to
> confirm that the association response "hits the air" and to see if the AP
> sends any response?
>
> Thanks,
> Daniel
>
-------------------------------------------------------------------------
This SF.net email is sponsored by DB2 Express
Download DB2 Express C - the FREE version of DB2 express and take
control of your XML. No limits. Just data. Click to get it now.
http://sourceforge.net/powerbar/db2/
_______________________________________________
Zd1211-devs mailing list - http://zd1211.wiki.sourceforge.net/
Unsubscribe: https://lists.sourceforge.net/lists/listinfo/zd1211-devs
