Back again with more debugging output after enabling the debug option in
kernel 2.6.23-gentoo-r5, that showed the same symptoms. This is what dmesg|
grep zd yields:
zd1211rw usb_init()
zd1211rw 1-10.2:1.0: zd_netdev_alloc() netdev->flags 0x1002
zd1211rw 1-10.2:1.0: zd_netdev_alloc() netdev->features 0x00000000
zd1211rw 1-10.2:1.0: zd_chip_read_mac_addr_fw()
zd1211rw 1-10.2:1.0: probe() successful
zd1211rw 1-10.2:1.0: eth1
usbcore: registered new interface driver zd1211rw
zd1211rw initialized
zd1211rw 1-10.2:1.0: zd_usb_init_hw()
usb 1-10.2: request_fw_file() fw name zd1211/zd1211b_ub
usb 1-10.2: request_fw_file() fw name zd1211/zd1211b_uphr
zd1211rw 1-10.2:1.0: zd_usb_enable_int()
zd1211rw 1-10.2:1.0: zd_usb_enable_int() submit urb ffff81003d3d0680
zd1211rw 1-10.2:1.0: zd_chip_init_hw()
zd1211rw 1-10.2:1.0: dump_cr() CR_AFTER_PNP 0x00000000
zd1211rw 1-10.2:1.0: dump_cr() CR_GPI_EN 0x00000000
zd1211rw 1-10.2:1.0: dump_cr() CR_INTERRUPT 0x00000000
zd1211rw 1-10.2:1.0: read_fw_regs_offset() fw_regs_base: 0xf772
zd1211rw 1-10.2:1.0: read_pod() E2P_POD 0x80000084
zd1211rw 1-10.2:1.0: read_pod() RF AL2230_RF 0x4 PA type 0x0 patch CCK 0 patch
CR157 0 patch 6M 0 new PHY 1 link LED2 tx led 1
zd1211rw 1-10.2:1.0: hw_init()
zd1211rw 1-10.2:1.0: zd1211b_hw_reset_phy()
zd1211rw 1-10.2:1.0: zd_chip_lock_phy_regs() CR_REG1: 0x00 -> 0x00
zd1211rw 1-10.2:1.0: zd_chip_unlock_phy_regs() CR_REG1: 0x00 -> 0x80
zd1211rw 1-10.2:1.0: zd1211b_hw_init_hmac()
zd1211rw 1-10.2:1.0: get_aw_pt_bi() aw 0 pt 0 bi 0
zd1211rw 1-10.2:1.0: set_aw_pt_bi() aw 0 pt 99 bi 100
zd1211rw 1-10.2:1.0: zd_chip_lock_phy_regs() CR_REG1: 0xa0 -> 0x20
zd1211rw 1-10.2:1.0: zd_usb_rfwrite() value 0x0241000 bits 24
zd1211rw 1-10.2:1.0: zd_chip_unlock_phy_regs() CR_REG1: 0x20 -> 0xa0
zd1211rw 1-10.2:1.0: firmware version 4725
zd1211rw 1-10.2:1.0: dump_fw_registers() FW_FIRMWARE_VER 0x4725
zd1211rw 1-10.2:1.0: dump_fw_registers() FW_USB_SPEED 0x0001
zd1211rw 1-10.2:1.0: dump_fw_registers() FW_FIX_TX_RATE 0x0000
zd1211rw 1-10.2:1.0: dump_fw_registers() FW_LINK_STATUS 0x0000
zd1211rw 1-10.2:1.0: dump_cr() CR_AFTER_PNP 0x00000001
zd1211rw 1-10.2:1.0: dump_cr() CR_GPI_EN 0x00000000
zd1211rw 1-10.2:1.0: dump_cr() CR_INTERRUPT 0x00000000
zd1211rw 1-10.2:1.0: zd1211b chip 1582:6003 v4810 high 00-11-f6 AL2230_RF
pa0 ---NS
zd1211rw 1-10.2:1.0: zd_read_regdomain() regdomain: 0x30
zd1211rw 1-10.2:1.0: regdomain 0x30
zd1211rw 1-10.2:1.0: zd_usb_disable_int() urb ffff81003d3d0680 killed
zd1211rw 1-10.2:1.0: zd_usb_enable_int()
zd1211rw 1-10.2:1.0: zd_usb_enable_int() submit urb ffff81003d3d0680
zd1211rw 1-10.2:1.0: zd_write_mac_addr() mac addr 00:11:f6:7f:fa:03
zd1211rw 1-10.2:1.0: zd_chip_set_basic_rates_locked() ff0f
zd1211rw 1-10.2:1.0: zd_usb_ioread16v() read timed out
zd1211rw 1-10.2:1.0: zd_ioread32v_locked() error: zd_ioread16v_locked. Error
number -110
zd1211rw 1-10.2:1.0: error ioread32(CR_REG1): -110
zd1211rw 1-10.2:1.0: zd_usb_disable_int() urb ffff81003d3d0680 killed
zd1211rw 1-10.2:1.0: set_security()
zd1211rw 1-10.2:1.0: set_security() .active_key = 0
zd1211rw 1-10.2:1.0: set_security() .level = 1
zd1211rw 1-10.2:1.0: set_security() .enabled = 1
zd1211rw 1-10.2:1.0: set_security() .encrypt = 1
For the sake of completeness, I attached the whole dmesg output.
Hope this will help.
Greets,
Andreas
Linux version 2.6.23-gentoo-r5 ([EMAIL PROTECTED]) (gcc version 4.1.2 (Gentoo
4.1.2 p1.0.2)) #2 SMP Sat Dec 29 15:35:45 CET 2007
Command line: root=/dev/sda1
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
BIOS-e820: 00000000c0000000 - 00000000d0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 159) 0 entries of 3200 used
Entering add_active_range(0, 256, 262128) 1 entries of 3200 used
end_pfn_map = 1048576
DMI 2.3 present.
ACPI: RSDP 000F6D90, 0014 (r0 Nvidia)
ACPI: RSDT 3FFF3000, 0030 (r1 Nvidia AWRDACPI 42302E31 AWRD 1010101)
ACPI: FACP 3FFF3040, 0074 (r1 Nvidia AWRDACPI 42302E31 AWRD 1010101)
ACPI: DSDT 3FFF30C0, 4C3F (r1 NVIDIA AWRDACPI 1000 MSFT 100000C)
ACPI: FACS 3FFF0000, 0040
ACPI: MCFG 3FFF7D80, 003C (r1 Nvidia AWRDACPI 42302E31 AWRD 1010101)
ACPI: APIC 3FFF7D00, 007C (r1 Nvidia AWRDACPI 42302E31 AWRD 1010101)
Scanning NUMA topology in Northbridge 24
CPU has 2 num_cores
No NUMA configuration found
Faking a node at 0000000000000000-000000003fff0000
Entering add_active_range(0, 0, 159) 0 entries of 3200 used
Entering add_active_range(0, 256, 262128) 1 entries of 3200 used
Bootmem setup node 0 0000000000000000-000000003fff0000
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1048576
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0 -> 159
0: 256 -> 262128
On node 0 totalpages: 262031
DMA zone: 56 pages used for memmap
DMA zone: 1565 pages reserved
DMA zone: 2378 pages, LIFO batch:0
DMA32 zone: 3527 pages used for memmap
DMA32 zone: 254505 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 48000000 (gap: 40000000:80000000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 31720 bytes of per cpu data
Built 1 zonelists in Node order. Total pages: 256883
Policy zone: DMA32
Kernel command line: root=/dev/sda1
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Marking TSC unstable due to TSCs unsynchronized
time.c: Detected 2211.361 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Checking aperture...
CPU 0: aperture @ 1432000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Memory: 1027372k/1048512k available (3437k kernel code, 20752k reserved, 1751k
data, 324k init)
Calibrating delay using timer specific routine.. 4425.43 BogoMIPS (lpj=8850870)
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 0/0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Parsing all Control Methods:
Table [DSDT](id 0001) - 771 Objects with 83 Devices 269 Methods 30 Regions
tbxface-0598 [00] tb_load_namespace : ACPI Tables successfully acquired
evxfevnt-0091 [00] enable : Transition to ACPI mode successful
Using local APIC timer interrupts.
result 12564576
Detected 12.564 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 4422.94 BogoMIPS (lpj=8845888)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
AMD Athlon(tm) 64 X2 Dual Core Processor 4200+ stepping 02
Brought up 2 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at c0000000 - cfffffff
PCI: No mmconfig possible on device 00:18
evgpeblk-0956 [00] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9
evgpeblk-0956 [00] ev_create_gpe_block : GPE 20 to 5F [_GPE] 8 regs on int 0x9
evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 7 Wake, Enabled 0 Runtime GPEs
in this block
evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 0 Wake, Enabled 0 Runtime GPEs
in this block
ACPI: EC: Look up EC in DSDT
Completing Region/Field/Buffer/Package
initialization:........................................................................
Initialized 26/30 Regions 1/1 Fields 32/32 Buffers 13/22 Packages (780 nodes)
Initializing Device/Processor/Thermal objects by executing _INI methods:.
Executed 1 _INI methods requiring 1 _STA executions (examined 87 objects)
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:09.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 15 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 2.21 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NET: Registered protocol family 23
pnp: 00:01: ioport range 0x1000-0x107f has been reserved
pnp: 00:01: ioport range 0x1080-0x10ff has been reserved
pnp: 00:01: ioport range 0x1400-0x147f has been reserved
pnp: 00:01: ioport range 0x1480-0x14ff has been reserved
pnp: 00:01: ioport range 0x1800-0x187f has been reserved
pnp: 00:01: ioport range 0x1880-0x18ff has been reserved
pnp: 00:0d: iomem range 0xc0000000-0xcfffffff could not be reserved
pnp: 00:0e: iomem range 0xd1800-0xd3fff has been reserved
pnp: 00:0e: iomem range 0xf0000-0xf7fff could not be reserved
pnp: 00:0e: iomem range 0xf8000-0xfbfff could not be reserved
pnp: 00:0e: iomem range 0xfc000-0xfffff could not be reserved
PCI: Bridge: 0000:00:09.0
IO window: 9000-9fff
MEM window: e4000000-e5ffffff
PREFETCH window: e6000000-e60fffff
PCI: Bridge: 0000:00:0b.0
IO window: 6000-6fff
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0c.0
IO window: 8000-8fff
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0d.0
IO window: 7000-7fff
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0e.0
IO window: a000-afff
MEM window: e0000000-e3ffffff
PREFETCH window: d0000000-dfffffff
Time: acpi_pm clocksource has been installed.
PCI: Setting latency timer of device 0000:00:09.0 to 64
PCI: Setting latency timer of device 0000:00:0b.0 to 64
PCI: Setting latency timer of device 0000:00:0c.0 to 64
PCI: Setting latency timer of device 0000:00:0d.0 to 64
PCI: Setting latency timer of device 0000:00:0e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 9, 3145728 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Total HugeTLB memory allocated, 0
Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]).
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
PCI: Found disabled HT MSI Mapping on 0000:00:0b.0
PCI: Found enabled HT MSI Mapping on 0000:00:00.0
PCI: Linking AER extended capability on 0000:00:0b.0
PCI: Found disabled HT MSI Mapping on 0000:00:0c.0
PCI: Found enabled HT MSI Mapping on 0000:00:00.0
PCI: Linking AER extended capability on 0000:00:0c.0
PCI: Found disabled HT MSI Mapping on 0000:00:0d.0
PCI: Found enabled HT MSI Mapping on 0000:00:00.0
PCI: Linking AER extended capability on 0000:00:0d.0
PCI: Found disabled HT MSI Mapping on 0000:00:0e.0
PCI: Found enabled HT MSI Mapping on 0000:00:00.0
PCI: Linking AER extended capability on 0000:00:0e.0
Boot video device is 0000:05:00.0
lp: driver loaded but no devices found
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102
Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60
seconds).
Hangcheck: Using get_cycles().
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input1
ACPI: Power Button (CM) [PWRB]
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
parport_pc 00:0a: reported by Plug and Play ACPI
parport0: PC-style at 0x378, irq 7 [PCSPP(,...)]
lp0: using parport0 (interrupt-driven).
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: module loaded
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
Copyright (c) 1999-2006 Intel Corporation.
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APCH] -> GSI 23 (level, low) ->
IRQ 23
PCI: Setting latency timer of device 0000:00:0a.0 to 64
forcedeth: using HIGHDMA
eth0: forcedeth.c: subsystem: 01458:e000 bound to 0000:00:0a.0
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver net1080
usbcore: registered new interface driver zaurus
netconsole: not configured, aborting
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0
NFORCE-CK804: chipset revision 242
NFORCE-CK804: not 100% native mode: will probe irqs later
NFORCE-CK804: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: Maxtor 6Y160P0, ATA DISK drive
hda: selected mode 0x46
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: _NEC DVD_RW ND-3500AG, ATAPI CD/DVD-ROM drive
hdc: selected mode 0x42
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: Host Protected Area detected.
current capacity is 320170943 sectors (163927 MB)
native capacity is 320173056 sectors (163928 MB)
hda: Host Protected Area disabled.
hda: 320173056 sectors (163928 MB) w/7936KiB Cache, CHS=19929/255/63, UDMA(133)
hda: cache flushes supported
hda: hda1 hda2 hda3 < hda5 hda6 hda7 > hda4
hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
3ware Storage Controller device driver for Linux v1.26.02.002.
sata_nv 0000:00:07.0: version 3.5
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [APSI] -> GSI 22 (level, low) ->
IRQ 22
sata_nv 0000:00:07.0: Using ADMA mode
PCI: Setting latency timer of device 0000:00:07.0 to 64
scsi0 : sata_nv
scsi1 : sata_nv
ata1: SATA max UDMA/133 cmd 0xffffc200001da480 ctl 0xffffc200001da4a0 bmdma
0x000000000001cc00 irq 22
ata2: SATA max UDMA/133 cmd 0xffffc200001da580 ctl 0xffffc200001da5a0 bmdma
0x000000000001cc08 irq 22
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATA-7: SAMSUNG SP2004C, VM100-33, max UDMA7
ata2.00: 390721968 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access ATA SAMSUNG SP2004C VM10 PQ: 0 ANSI: 5
ata2: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
sd 1:0:0:0: [sda] 390721968 512-byte hardware sectors (200050 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 1:0:0:0: [sda] 390721968 512-byte hardware sectors (200050 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sda: sda1 sda2 sda3 sda4
sd 1:0:0:0: [sda] Attached SCSI disk
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APSJ] -> GSI 21 (level, low) ->
IRQ 21
sata_nv 0000:00:08.0: Using ADMA mode
PCI: Setting latency timer of device 0000:00:08.0 to 64
scsi2 : sata_nv
scsi3 : sata_nv
ata3: SATA max UDMA/133 cmd 0xffffc200001dc480 ctl 0xffffc200001dc4a0 bmdma
0x000000000001e000 irq 21
ata4: SATA max UDMA/133 cmd 0xffffc200001dc580 ctl 0xffffc200001dc5a0 bmdma
0x000000000001e008 irq 21
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
usbmon: debugfs is not available
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 20 (level, low) ->
IRQ 20
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: irq 20, io mem 0xfeb00000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 23 (level, low) ->
IRQ 23
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 23, io mem 0xe6101000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
USB Universal Host Controller Interface driver v3.0
usb 1-10: new high speed USB device using ehci_hcd and address 2
usb 1-10: configuration #1 chosen from 1 choice
hub 1-10:1.0: USB hub found
hub 1-10:1.0: 4 ports detected
usb 1-10.2: new high speed USB device using ehci_hcd and address 3
usb 1-10.2: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input2
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
oprofile: using NMI interrupt.
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
NET: Registered protocol family 17
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <[EMAIL PROTECTED]>
ieee80211_crypt: registered algorithm 'NULL'
powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor 4200+ processors
(2 cpu cores) (version 2.00.00)
powernow-k8: 0 : fid 0xe (2200 MHz), vid 0x8
powernow-k8: 1 : fid 0x2 (1000 MHz), vid 0x12
logips2pp: Detected unknown logitech mouse model 89
input: ImExPS/2 Logitech Explorer Mouse as /class/input/input3
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 324k freed
i2c-adapter i2c-0: nForce2 SMBus adapter at 0x1c00
i2c-adapter i2c-1: nForce2 SMBus adapter at 0x1c40
zd1211rw usb_init()
usb 1-10.2: print_id() 1582:6003 v4810 high
usb 1-10.2: reset high speed USB device using ehci_hcd and address 3
ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCJ] -> GSI 22 (level, low) ->
IRQ 22
PCI: Setting latency timer of device 0000:00:04.0 to 64
zd1211rw 1-10.2:1.0: zd_netdev_alloc() netdev->flags 0x1002
zd1211rw 1-10.2:1.0: zd_netdev_alloc() netdev->features 0x00000000
zd1211rw 1-10.2:1.0: zd_chip_read_mac_addr_fw()
zd1211rw 1-10.2:1.0: probe() successful
zd1211rw 1-10.2:1.0: eth1
usbcore: registered new interface driver zd1211rw
zd1211rw initialized
net eth2: device_rename: sysfs_create_symlink failed (-17)
udev: renamed network interface eth1 to eth2
intel8x0_measure_ac97_clock: measured 58658 usecs
intel8x0: clocking to 47057
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ACPI: PCI Interrupt 0000:01:08.1[A] -> Link [APC1] -> GSI 16 (level, low) ->
IRQ 16
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [APC3] -> GSI 18 (level, low) ->
IRQ 18
nvidiafb: Device ID: 10de0402
nvidiafb: unknown NV_ARCH
EXT3 FS on sda1, internal journal
via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [APC4] -> GSI 19 (level, low) ->
IRQ 19
eth1: VIA Rhine II at 0x19000, 00:05:5d:09:b1:27, IRQ 19.
eth1: MII PHY found at address 8, status 0x7809 advertising 01e1 Link 0000.
Linux video capture interface: v2.00
bttv: driver version 0.9.17 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC1] -> GSI 16 (level, low) ->
IRQ 16
bttv0: Bt878 (rev 2) at 0000:01:08.0, irq: 16, latency: 32, mmio: 0xe6000000
bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
bttv0: using: Hauppauge (bt878) [card=10,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init]
bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
tveeprom 2-0050: Hauppauge model 37284, rev B121, serial# 3497320
tveeprom 2-0050: tuner model is Philips FM1216 (idx 21, type 5)
tveeprom 2-0050: TV standards PAL(B/G) (eeprom 0x04)
tveeprom 2-0050: audio processor is MSP3410D (idx 5)
tveeprom 2-0050: has radio
bttv0: Hauppauge eeprom indicates model#37284
bttv0: tuner type=5
bttv0: i2c: checking for MSP34xx @ 0x80... found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
bttv0: PLL: 28636363 => 35468950 .. ok
tuner 2-0042: chip found @ 0x84 (bt878 #0 [sw])
tda9887 2-0042: tda988[5/6/7] found @ 0x42 (tuner)
tuner 2-0061: chip found @ 0xc2 (bt878 #0 [sw])
tuner 2-0061: type set to 5 (Philips PAL_BG (FI1216 and compatibles))
tuner 2-0061: type set to 5 (Philips PAL_BG (FI1216 and compatibles))
NTFS driver 2.1.28 [Flags: R/O MODULE].
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
ip6_tables: (C) 2000-2006 Netfilter Core Team
i2c /dev entries driver
it87: Found IT8712F chip at 0x290, revision 5
u32 classifier
Actions configured
netem: version 1.2
msp3400 2-0040: MSP3410D-B4 found @ 0x80 (bt878 #0 [sw])
msp3400 2-0040: MSP3410D-B4 supports nicam, mode is autodetect
Bridge firewalling registered
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <[EMAIL PROTECTED]>
ieee80211_crypt: registered algorithm 'WEP'
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: mounting fs with errors, running e2fsck is recommended
EXT3 FS on hda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: mounting fs with errors, running e2fsck is recommended
EXT3 FS on sda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 3301316k swap on /dev/hda7. Priority:-1 extents:1 across:3301316k
zd1211rw 1-10.2:1.0: zd_usb_init_hw()
usb 1-10.2: request_fw_file() fw name zd1211/zd1211b_ub
usb 1-10.2: upload_firmware() firmware device id 0x4810 is equal to the actual
device id
usb 1-10.2: request_fw_file() fw name zd1211/zd1211b_uphr
usb 1-10.2: upload_code() transfer size 4096
usb 1-10.2: upload_code() transfer size 1024
usb 1-10.2: upload_code() firmware confirm return value 0x01
zd1211rw 1-10.2:1.0: zd_usb_enable_int()
zd1211rw 1-10.2:1.0: zd_usb_enable_int() submit urb ffff81003d3d0680
zd1211rw 1-10.2:1.0: zd_chip_init_hw()
zd1211rw 1-10.2:1.0: dump_cr() CR_AFTER_PNP 0x00000000
zd1211rw 1-10.2:1.0: dump_cr() CR_GPI_EN 0x00000000
zd1211rw 1-10.2:1.0: dump_cr() CR_INTERRUPT 0x00000000
zd1211rw 1-10.2:1.0: read_fw_regs_offset() fw_regs_base: 0xf772
zd1211rw 1-10.2:1.0: read_pod() E2P_POD 0x80000084
zd1211rw 1-10.2:1.0: read_pod() RF AL2230_RF 0x4 PA type 0x0 patch CCK 0 patch
CR157 0 patch 6M 0 new PHY 1 link LED2 tx led 1
zd1211rw 1-10.2:1.0: hw_init()
zd1211rw 1-10.2:1.0: zd1211b_hw_reset_phy()
zd1211rw 1-10.2:1.0: zd_chip_lock_phy_regs() CR_REG1: 0x00 -> 0x00
zd1211rw 1-10.2:1.0: zd_chip_unlock_phy_regs() CR_REG1: 0x00 -> 0x80
zd1211rw 1-10.2:1.0: zd1211b_hw_init_hmac()
zd1211rw 1-10.2:1.0: get_aw_pt_bi() aw 0 pt 0 bi 0
zd1211rw 1-10.2:1.0: set_aw_pt_bi() aw 0 pt 99 bi 100
zd1211rw 1-10.2:1.0: zd_chip_lock_phy_regs() CR_REG1: 0xa0 -> 0x20
zd1211rw 1-10.2:1.0: zd_usb_rfwrite() value 0x0241000 bits 24
zd1211rw 1-10.2:1.0: zd_chip_unlock_phy_regs() CR_REG1: 0x20 -> 0xa0
zd1211rw 1-10.2:1.0: firmware version 4725
zd1211rw 1-10.2:1.0: dump_fw_registers() FW_FIRMWARE_VER 0x4725
zd1211rw 1-10.2:1.0: dump_fw_registers() FW_USB_SPEED 0x0001
zd1211rw 1-10.2:1.0: dump_fw_registers() FW_FIX_TX_RATE 0x0000
zd1211rw 1-10.2:1.0: dump_fw_registers() FW_LINK_STATUS 0x0000
zd1211rw 1-10.2:1.0: dump_cr() CR_AFTER_PNP 0x00000001
zd1211rw 1-10.2:1.0: dump_cr() CR_GPI_EN 0x00000000
zd1211rw 1-10.2:1.0: dump_cr() CR_INTERRUPT 0x00000000
zd1211rw 1-10.2:1.0: zd1211b chip 1582:6003 v4810 high 00-11-f6 AL2230_RF pa0
---NS
zd1211rw 1-10.2:1.0: zd_read_regdomain() regdomain: 0x30
zd1211rw 1-10.2:1.0: regdomain 0x30
zd1211rw 1-10.2:1.0: zd_usb_disable_int() urb ffff81003d3d0680 killed
zd1211rw 1-10.2:1.0: zd_usb_enable_int()
zd1211rw 1-10.2:1.0: zd_usb_enable_int() submit urb ffff81003d3d0680
zd1211rw 1-10.2:1.0: zd_write_mac_addr() mac addr 00:11:f6:7f:fa:03
zd1211rw 1-10.2:1.0: zd_chip_set_basic_rates_locked() ff0f
zd1211rw 1-10.2:1.0: zd_usb_ioread16v() read timed out
zd1211rw 1-10.2:1.0: zd_ioread32v_locked() error: zd_ioread16v_locked. Error
number -110
zd1211rw 1-10.2:1.0: error ioread32(CR_REG1): -110
zd1211rw 1-10.2:1.0: zd_usb_disable_int() urb ffff81003d3d0680 killed
zd1211rw 1-10.2:1.0: set_security()
zd1211rw 1-10.2:1.0: set_security() .active_key = 0
zd1211rw 1-10.2:1.0: set_security() .level = 1
zd1211rw 1-10.2:1.0: set_security() .enabled = 1
zd1211rw 1-10.2:1.0: set_security() .encrypt = 1
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Associate: failed to initiate scan. Is device up?
hda: selected mode 0x46
hdc: selected mode 0x42
eth0: no IPv6 routers present
vpn: no IPv6 routers present
-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2005.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
Zd1211-devs mailing list - http://zd1211.wiki.sourceforge.net/
Unsubscribe: https://lists.sourceforge.net/lists/listinfo/zd1211-devs
