Hi Larry,
thank you for your answer.
This is same test I did. After this I lowered again to 4800...result:
iaxmodem receives at 9600 b/s.....that's why I cannot solve the puzzle.
I put that line (Class1RMQueryCmd: "!24,48,72") in config.IAXtty
and tried other configuration files too but I always get faxes at 9600.
Thank you
Giorgio
On 05/16/2012 03:59 PM, Larry Moore wrote:
Read the subject line more closely.
Tested receiving too,
I set the Send & Receive speed of the receiving analogue modem to that
below, the log file on the sending modem (iaxmodem) reported it
capable of 9600.
May 16 21:32:04.28: [ 2335]: REMOTE best rate 9600 bit/s
May 16 21:32:04.28: [ 2335]: REMOTE max A3 page width (303 mm)
May 16 21:32:04.28: [ 2335]: REMOTE max unlimited page length
May 16 21:32:04.28: [ 2335]: REMOTE best vres R16 x 15.4 line/mm
May 16 21:32:04.28: [ 2335]: REMOTE format support: MH, MR, MMR
May 16 21:32:04.28: [ 2335]: REMOTE supports T.30 Annex A, 256-byte ECM
May 16 21:32:04.28: [ 2335]: REMOTE best 0 ms/scanline
May 16 21:32:04.28: [ 2335]: USE 9600 bit/s
Perhaps the issue is with Hylafax.
Setting the Transmit & Receive strings to "!24,48,72,96" seems to
yield the most reliability in transmission
Cheers,
Larry.
On 16/05/2012 7:23 PM, Larry Moore wrote:
I have iaxmodem version 1.2.0 installed on my system.
I have set the following in the IAX configuration file, SIGHUP'd
FaxGetty and submitted a single page outbound fax via Asterisk;
Class1RMQueryCmd: "!24,48,72" # enable this to disable V.17
receiving
Class1TMQueryCmd: "!24,48,72" # enable this to disable V.17
sending
The resulting output from my T.38 Gateway reports the following;
-- Connection Statistics
Bit Rate :7200
ECM : No
Pages : 1
-- Hungup 'IAX2/iaxmodem0-11055'
I also tested with the maximum speed set to 4800, the image was
received however the responses to EOP timed out, I don't know if the
is to do with my Asterisk T.38 gateway or my VoIP providers T.38
gateway. The result was the fax was retried for the defined number of
attempts.
Cheers,
Larry.
On 16/05/2012 6:28 PM, gincantalupo wrote:
Hi all,
I'm trying to lower my iaxmodem speed but still I haven't found any
solution...I tried to add
Class1RMQueryCmd: "!24,48,72"
to config.IAXtty but does not work...Hylafax says it it running at 9600
(sometimes at 14400) baud..
Any ideas?
Thank you.
Giorgio
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided byhttp://www.api-digital.com --
New to Asterisk? Join us for a live introductory webinar every Thurs:
http://www.asterisk.org/hello
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided byhttp://www.api-digital.com --
New to Asterisk? Join us for a live introductory webinar every Thurs:
http://www.asterisk.org/hello
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
New to Asterisk? Join us for a live introductory webinar every Thurs:
http://www.asterisk.org/hello
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
New to Asterisk? Join us for a live introductory webinar every Thurs:
http://www.asterisk.org/hello
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
