The provider is the timing source. Both wanpipe1.conf and
system.conf have the timing sources set to the remote side:
TE_CLOCK = NORMAL
span=1,1,0,CAS,HDB3
I still have a feeling that the problem is on the providers side as
during testing we never saw the issue.
I have modified wanpipe1.conf to be CAS but the strange thing is
that the freepbx gui does show CAS there but sets CCS on the
configuration file. Now I have to wait and see if the problem persists.
On 08/03/22 11:54, Duncan Turnbull wrote:
It’s been a r we hike since we used these cards. This example may help
https://wiki.freepbx.org/plugins/servlet/mobile?contentId=73007457#content/view/73007457
My thinking is it sounds like a timing error. Make sure your provider
is the timing source. Once it loses time you will get dropped calls
until it resyncs
Good luck
On 9/03/2022, at 4:25 AM, Steinwendtner <steinwendt...@gmx.net> wrote:
Hello,
I must admit that I have never set up an asterisk system with R2
signalling. But from the config files
point of view, you stated TE_SIG_MODE in wanpipe1.conf as ccs which
should be cas, right ?
If this does not help, you need to connect an external E1 Monitor.
Regards,
Hans
Am 08.03.22 um 06:41 schrieb Carlos Chavez:
Last month we switched a Panasonic pbx with a Freepbx 16
appliance. We use a single E1 in MFC/R2 (Mexico) with Telmex as a
provider. This was connected for a couple of days for testing with no
problems before the client moved offices to a new location. In the new
location we are now having a problem every few days where we get the
following error:
[2022-03-07 07:30:11] ERROR[3469][C-0000004c] chan_dahdi.c: Chan 10 -
Protocol error. Reason = Seize Timeout, R2 State = Seize Transmitted, MF
state = MF Engine Off, MF Group = Forward MF init, CAS = 0x08
[2022-03-07 07:30:44] ERROR[29573] chan_dahdi.c: Chan 10 - Protocol
error. Reason = Seize Timeout, R2 State = Clear Forward Transmitted, MF
state = MF Engine Off, MF Group = Forward MF init, CAS = 0x08
[2022-03-07 07:32:15] ERROR[3704][C-0000004e] chan_dahdi.c: Chan 10 -
Protocol error. Reason = Seize Timeout, R2 State = Seize Transmitted, MF
state = MF Engine Off, MF Group = Forward MF init, CAS = 0x08
[2022-03-07 07:32:52] ERROR[29573] chan_dahdi.c: Chan 10 - Protocol
error. Reason = Seize Timeout, R2 State = Clear Forward Transmitted, MF
state = MF Engine Off, MF Group = Forward MF init, CAS = 0x08
When we see that error the E1 will no longer send or receive
calls. Our solution has been to stop and restart Asterisk and
Wanconfig/Dahdi to restore service. Since restarting solves it I am
wondering if the problem is on my side and not on the providers. So far
it happens once or twice a week. When we report this to the provider
they simply state that the problem is on our side (it is their default
position) unless we can provide evidence to the contrary. Any
recommendations on how to debug this?
Here is wanpipe1.conf:
[devices]
wanpipe1 = WAN_AFT_TE1, Comment
[interfaces]
w1g1 = wanpipe1, , TDM_VOICE, Comment
[wanpipe1]
CARD_TYPE = AFT
S514CPU = A
CommPort = PRI
AUTO_PCISLOT = NO
PCISLOT = 4
PCIBUS = 8
FE_MEDIA = E1
FE_LCODE = HDB3
FE_FRAME = NCRC4
FE_LINE = 1
TE_CLOCK = NORMAL
TE_REF_CLOCK = 0
TE_SIG_MODE = CCS
TE_HIGHIMPEDANCE = NO
TE_RX_SLEVEL = 430
HW_RJ45_PORT_MAP = DEFAULT
LBO = 120OH
FE_TXTRISTATE = NO
MTU = 1500
UDPPORT = 9000
TTL = 255
IGNORE_FRONT_END = NO
TDMV_SPAN = 1
TDMV_DCHAN = 16
TE_AIS_MAINTENANCE = NO #NO: defualt YES: Start port in AIS
Blue Alarm and keep line down
#wanpipemon -i w1g1 -c Ttx_ais_off to
disable AIS maintenance mode
#wanpipemon -i w1g1 -c Ttx_ais_on to
enable AIS maintenance mode
TDMV_HW_DTMF = NO # YES: receive dtmf events from hardware
TDMV_HW_FAX_DETECT = NO # YES: receive fax 1100hz events
from hardware
HWEC_OPERATION_MODE = OCT_NORMAL # OCT_NORMAL: echo cancelation
enabled with nlp (default)
# OCT_SPEECH: improves software
tone detection by disabling NLP (echo possible)
# OCT_NO_ECHO:disables echo
cancelation but allows VQE/tone functions.
HWEC_DTMF_REMOVAL = NO # NO: default YES: remove dtmf out of
incoming media (must have hwdtmf enabled)
HWEC_NOISE_REDUCTION = NO # NO: default YES: reduces noise on the
line - could break fax
HWEC_ACUSTIC_ECHO = NO # NO: default YES: enables acustic echo
cancelation
HWEC_NLP_DISABLE = NO # NO: default YES: guarantees software
tone detection (possible echo)
HWEC_TX_AUTO_GAIN = 0 # 0: disable -40-0: default tx audio
level to be maintained (-20 default)
HWEC_RX_AUTO_GAIN = 0 # 0: disable -40-0: default tx audio
level to be maintained (-20 default)
HWEC_TX_GAIN = 0 # 0: disable -24-24: db values to
be applied to tx signal
HWEC_RX_GAIN = 0 # 0: disable -24-24: db values to
be applied to tx signal
[w1g1]
ACTIVE_CH = ALL
TDMV_HWEC = NO
MTU = 8
Here is system.conf
span=1,1,0,CAS,HDB3
cas=1-10,11-15,17-31:1101
echocanceller=oslec,1-10,11-15,17-31
loadzone=mx
defaultzone=mx
Here is chan_dahdi.conf
signalling=mfcr2
mfcr2_variant=mx
mfcr2_get_ani_first=no
mfcr2_max_ani=10
mfcr2_max_dnis=4
mfcr2_category=national_priority_subscriber
mfcr2_call_files=no
mfcr2_mfback_timeout=-1
mfcr2_metering_pulse_timeout=-1
mfcr2_allow_collect_calls=yes
mfcr2_double_answer=no
mfcr2_immediate_accept=no
mfcr2_accept_on_offer=yes
mfcr2_skip_category=no
mfcr2_forced_release=no
mfcr2_charge_calls=yes
group=0
context=from-digital
channel=>1-10
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
Check out the new Asterisk community forum at:
https://community.asterisk.org/
New to Asterisk? Start here:
https://wiki.asterisk.org/wiki/display/AST/Getting+Started
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
--
Telecomunicaciones Abiertas de México S.A. de C.V.
Carlos Chávez
+52 (55)8116-9161
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
Check out the new Asterisk community forum at: https://community.asterisk.org/
New to Asterisk? Start here:
https://wiki.asterisk.org/wiki/display/AST/Getting+Started
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
