Dear Steve I installed the new version of spandsp 1i i used Mandrake 9.2 and upgrade my libtiff with newer and also copy tiff header files as you write in README: libtiff3-3.5.7-11mdk libtiff-progs-3.5.7-11mdk libtiff3-devel-3.5.7-11mdk -- But when i send a Fax from my Canon B150 i have the following error: -- Starting simple switch on 'Zap/33-1' -- Executing RxFAX("Zap/33-1", "/home/user/testfax.tif") in new stack Changed from phase 0 to 1 Slow carrier up Slow carrier down Start receiving document Changed from phase 1 to 4 Sending ident >>> CSI: 40 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 DIS: Preferred octets: 256 Can receive fax Supported data signalling rates: V.27ter and V.29 R8x7.7lines/mm and/or 200x200pels/25.4mm OK 2D coding OK Scan line length: 215mm Recording length: A4 (297mm) Receiver's minimum scan line time: 0ms at 3.85 l/mm: T7.7 = T3.85 R8x15.4lines/mm OK Minimum scan line time for higher resolutions: T15.4 = T7.7 >>> DIS: 80 00 ce f0 80 80 01 HDLC underflow in state 9 Changed from phase 4 to 3 Slow carrier up <<< TSI: 43 37 30 38 30 35 33 31 33 33 30 20 20 20 20 20 20 20 20 20 20 TSI without final frame tag Remote fax gave TSI as: "031xxxxx" <<< DCS: 83 00 86 a0 00 DCS with final frame tag In state 9 DCS: Can receive fax Selected data signalling rate: V.29, 9600bps 2D coding OK Scan line length: 215mm Recording length: A4 (297mm) Minimum scan line time: 10ms Get at 9600 Changed from phase 3 to 5 Fast carrier up Floating point exception [EMAIL PROTECTED] asterisk]# Ouch ... error while writing audio data: : Broken pipe Ouch ... error while writing audio data: : Broken pipe ----- And Crashed... The Fax is connect to FXS line of my TDM400 Canon--->TDM400
Finaly i used Asterisk cvs Satble 1_0. Can you give some tips :-). Thanks in advance Dimitri On Monday 29 March 2004 13:00, Reynaldo Simbulan wrote: > Hi Steve, > > You're right it is just the libtiff. I have uninstall 3.6 and 3.5 and > reinstall 3.5.7-11. Thanks, it is now receiving fax. > > Although after receiving the fax, the zap channel is not disconnecting. ? > On the fax client it was successfully sent and the tif file is complete. > > Here is my extensions.conf: > exten => s,1,Answer > exten => s,2,SetVar(FAXNAME=${TIMESTAMP}-${CALLERIDNUM}) > exten => s,3,RxFax(/var/lib/asterisk/fax/new/${FAXNAME}.tif) > exten => s,4,Hangup > exten => i,1,Hangup > exten => h,1,Hangup > > > And here is the log file: > > Page 1 of /var/lib/asterisk/fax/new/20040329-234801-0755965128.tif: > 1116 rows received > 0 total bad rows > 0 max consecutive bad rows > Rx page end detected > Changed from phase 5 to 3 > Slow carrier up > Slow carrier down > Slow carrier up > <<< EOP: 2f > EOP with final frame tag > In state 5 > Changed from phase 3 to 4 > > >>> MCF: 8c > > HDLC underflow in state 8 > Changed from phase 4 to 3 > Slow carrier up > <<< DCN: fb > DCN with final frame tag > In state 8 > Disconnecting > Changed from phase 3 to 7 > > *CLI> show channels > Channel (Context Extension Pri ) State Appl. Data > Zap/1-1 (faxserver s 3 ) Up RxFAX > /var/lib/asterisk/fax/new/20040329-234801-0755965128.tif > 1 active channel(s) > _______________________________________________ > Asterisk-Users mailing list > [EMAIL PROTECTED] > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users