upgrade to the following wanpipe and also upgrade the firmware o the crd (it's included in the wanpipe softwaare) ftp://ftp.sangoma.com/linux/custom/2.3.2/wanpipe-beta5g-2.3.2.tgz
On Thu, 17 Feb 2005 16:07:54 +0100, Kumak <[EMAIL PROTECTED]> wrote: > > Hello, > I have following problem with Sangoma A104 card: > > CLI> pri show span 1 > Primary D-channel: 16 > Status: Provisioned, Down, Active > Switchtype: EuroISDN > Type: CPE > Window Length: 0/7 > Sentrej: 0 > SolicitFbit: 0 > Retrans: 0 > Busy: 0 > Overlap Dial: 0 > T200 Timer: 1000 > T203 Timer: 10000 > T305 Timer: 30000 > T308 Timer: 4000 > T313 Timer: 4000 > N200 Counter: 3 > > NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI got event: HDLC Abort (6) on > Primary D-channel of span 1 > NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI got event: HDLC Abort (6) on > Primary D-channel of span 1 > NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI got event: HDLC Abort (6) on > Primary D-channel of span 1 > NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI got event: HDLC Abort (6) on > Primary D-channel of span 1 > > Any idea how to fix it? > > My configs: > > zaptel.conf: > > span=1,1,1,ccs,hdb3,crc4 > bchan=1-15,17-31 > dchan=16 > > zapata.conf > > [channels] > switchtype=euroisdn > pridialplan=unknown > overlapdial=no > usecallerid=yes > hidecallerid=yes > callwaiting=no > callwaitingcallerid=no > threewaycalling=no > transfer=no > cancallforward=no > callreturn=no > jitterbuffers=4 > echocancel=yes > echocancelwhenbridged=no > echotraining=yes > relaxdtmf=yes > rxgain=0.5 > txgain=0.9 > immediate=no > amaflags=billing > adsi=no > busydetect=no > callprogress=no > context = zapline1 > switchtype = euroisdn > group=1 > signalling = pri_cpe > channel => 1-15 > channel => 17-31 > > cat /proc/zaptel/1 : > > Span 1: WPE1/0 "wanpipe1 card 0" HDB3//CRC4 > > 1 WPE1/0/1 Clear (In use) > 2 WPE1/0/2 Clear (In use) > 3 WPE1/0/3 Clear (In use) > 4 WPE1/0/4 Clear (In use) > 5 WPE1/0/5 Clear (In use) > 6 WPE1/0/6 Clear (In use) > 7 WPE1/0/7 Clear (In use) > 8 WPE1/0/8 Clear (In use) > 9 WPE1/0/9 Clear (In use) > 10 WPE1/0/10 Clear (In use) > 11 WPE1/0/11 Clear (In use) > 12 WPE1/0/12 Clear (In use) > 13 WPE1/0/13 Clear (In use) > 14 WPE1/0/14 Clear (In use) > 15 WPE1/0/15 Clear (In use) > 16 WPE1/0/16 HDLCFCS (In use) > 17 WPE1/0/17 Clear (In use) > 18 WPE1/0/18 Clear (In use) > 19 WPE1/0/19 Clear (In use) > 20 WPE1/0/20 Clear (In use) > 21 WPE1/0/21 Clear (In use) > 22 WPE1/0/22 Clear (In use) > 23 WPE1/0/23 Clear (In use) > 24 WPE1/0/24 Clear (In use) > 25 WPE1/0/25 Clear (In use) > 26 WPE1/0/26 Clear (In use) > 27 WPE1/0/27 Clear (In use) > 28 WPE1/0/28 Clear (In use) > 29 WPE1/0/29 Clear (In use) > 30 WPE1/0/30 Clear (In use) > 31 WPE1/0/31 Clear (In use) > > Information from dmesg: > > Processing WAN device wanpipe1... > wanpipe1: Locating: A104 card, CPU A, PciSlot=8, PciBus=0 > wanpipe1: Found: A104 card, CPU A, PciSlot=8, PciBus=0, Port=0 > PCI: Found IRQ 10 for device 00:08.0 > wanpipe1: AFT PCI memory at 0xEE000000 > wanpipe1: IRQ 10 allocated to the AFT PCI card > wanpipe1: Initializing for SMP > wanpipe1: Starting AFT Quad Hardware Init. > wanpipe1: Enabling front end link monitor > wanpipe1: Global Chip Configuration: used=1 > wanpipe1: Global Front End Configuraton! > wanpipe1: T1/E1/J1 Global configuration! > wanpipe1: AFT Data Mux Bit Map: 0x76543210 > wanpipe1: Setting E1 configuration (Port 1)! > wanpipe1: All channels enabled > wanpipe1: Front end successful > wanpipe1: AFT Security: UnChannelised > wanpipe1: Configuring Device :wanpipe1 FrmVr=8 > wanpipe1: Global MTU = 1500 > wanpipe1: Global MRU = 1500 > wanpipe1: Data Mux Map = 0x76543210 > wanpipe1: Configuring Interface: w1g1 > wanpipe1:w1g1: Running in TDM Voice mode. > wanpipe1: AFT Fifo Level Map: 0x02082082 > wanpipe1: Registering interface to Zaptel span # 1! > wanpipe1: MRU :248 > wanpipe1: MTU :248 > wanpipe1: HDLC Eng :Off (Transparent) > wanpipe1: Data Mux Ctrl :On > wanpipe1:w1g1: Active channels = 0xFFFFFFFE > wanpipe1:w1g1: Setting first time slot to 1 > wanpipe1:w1g1: Config for Transparent mode: Idle=0 Len=248 > wanpipe1:w1g1: Allocating 65 dma skb len=256 Chaining=Off > > _______________________________________________ > Asterisk-Users mailing list > Asterisk-Users@lists.digium.com > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > -- Michal Bielicki http://www.asterisk.com.pl/ _______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users