Gábor Stefanik wrote:
> Hello World!
>
> Great news for Broadcom BCM4310/4312/4315 (PCI 14e4:4315) users:
> LP-PHY support is now at the point where it can be tested for functionality!
>
> So, go ahead, give it a try, and let's rock!
>
Patches applied, well manually, cause I wasn't able to extract a working
version from the emails or the weblink provided. Whats the recommended
method to apply these git patches on mailinglists?
Here goes:
# modprobe b43 verbose=3
[ 1596.228088] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x16, vendor
0x4243)
[ 1596.228100] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x0F,
vendor 0x4243)
[ 1596.228110] ssb: Core 2 found: PCMCIA (cc 0x80D, rev 0x0A, vendor 0x4243)
[ 1596.228120] ssb: Core 3 found: PCI-E (cc 0x820, rev 0x09, vendor 0x4243)
[ 1596.248050] ssb: Found rev 1 PMU (capabilities 0x02A62F01)
[ 1596.256780] ssb: SPROM revision 8 detected.
[ 1596.276093] ssb: Sonics Silicon Backplane found on PCI device
0000:10:00.0
[ 1596.281108] b43-phy2: Broadcom 4312 WLAN found (core revision 15)
[ 1596.324046] b43-phy2 debug: Found PHY: Analog 6, Type 5, Revision 1
[ 1596.324060] b43-phy2 debug: Found Radio: Manuf 0x17F, Version 0x2062,
Revision 2
[ 1596.348233] phy2: Selected rate control algorithm 'minstrel'
[ 1596.348349] Broadcom 43xx driver loaded [ Features: PL, Firmware-ID:
FW13 ]
# ifconfig wlan0 up
SIOCSIFFLAGS: Input/output error
[ 1689.356055] b43 ssb0:0: firmware: requesting b43/ucode15.fw
[ 1689.703918] b43 ssb0:0: firmware: requesting b43/lp0initvals15.fw
[ 1689.710418] b43 ssb0:0: firmware: requesting b43/lp0bsinitvals15.fw
[ 1689.852058] b43-phy2: Loading firmware version 410.2160 (2007-05-26
15:32:10)
[ 1689.854963] b43-phy2 debug: b2062: Using crystal tab entry 19200 kHz.
[ 1689.855468] b43-phy2 debug: RC calib: Failed to switch to channel 7,
error = -5
[ 1689.860016] b43-phy2 debug: Switch to init channel failed, error = -5.
[ 1689.860543] b43-phy2 ERROR: PHY init: Channel switch to default failed
Interface is not coming up, so cannot scan:
# iwlist wlan0 scan
wlan0 Interface doesn't support scanning : Network is down
# iwconfig wlan0
wlan0 IEEE 802.11bg Mode:Managed Access Point: Not-Associated
Tx-Power=0 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
# iw dev wlan0 info
Interface wlan0
ifindex 5
type managed
# iw phy phy2 info
Wiphy phy2
Band 1:
Frequencies:
* 2412 MHz [1] (27.0 dBm)
* 2417 MHz [2] (27.0 dBm)
* 2422 MHz [3] (27.0 dBm)
* 2427 MHz [4] (27.0 dBm)
* 2432 MHz [5] (27.0 dBm)
* 2437 MHz [6] (27.0 dBm)
* 2442 MHz [7] (27.0 dBm)
* 2447 MHz [8] (27.0 dBm)
* 2452 MHz [9] (27.0 dBm)
* 2457 MHz [10] (27.0 dBm)
* 2462 MHz [11] (27.0 dBm)
* 2467 MHz [12] (disabled)
* 2472 MHz [13] (disabled)
* 2484 MHz [14] (disabled)
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
max # scan SSIDs: 4
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* WDS
* monitor
* mesh point
_______________________________________________
Bcm43xx-dev mailing list
Bcm43xx-dev@lists.berlios.de
https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
