Hi Rolando, Nice work!
My advice - if everything works, don't touch it! It would be good to note your currently working combination of package versions, in case you have problems in the future. Cheers Jack On Mon, 5 Dec 2016, 12:01 Rolando Paz, <flx...@gmail.com> wrote: > Hi Jack > > I found this email > http://www.mail-archive.com/casper@lists.berkeley.edu/msg02504.html > > Then I used minicom and I replaced tcpborphserver2 > > root@roach:/usr/local/sbin# ls > fancontrol pwmconfig sensors-detect tcpborphserver2 tgtap > flash_eraseall sensord tb2server-allfix tcpborphserver2_old > root@roach:/usr/local/sbin# > > After this worked tut2! > > However, should I upgrade the versions of corr and katcp and filesystem? > > This is the output of ?help > > rolando@rolando-MS-7815:~$ telnet 192.168.100.2 7147 > Trying 192.168.100.2... > Connected to 192.168.100.2. > Escape character is '^]'. > #version poco-0.1 > #build-state poco-0.0a271150300 > ?help > #help sensor-dump dump\_sensor\_tree\_(?sensor-dump) > #help sensor-value query\_a\_sensor\_(?sensor-value\_sensor) > #help sensor-sampling > configure\_sensor\_(?sensor-sampling\_sensor\_[strategy\_[parameter]]) > #help sensor-list lists\_available\_sensors\_(?sensor-list\_[sensor]) > #help client-list displays\_client\_list\_(?client-list) > #help tap-stop stop\_a\_tgtap\_instance\_(?tap-stop\_register-name) > #help tap-start > start\_a\_tgtap\_instance\_(?tap-start\_tap-device\_register-name\_ip-address\_[port\_[mac]]) > #help wordwrite > writes\_a\_word\_(?wordwrite\_register-name\_word-offset\_payload\_...) > #help wordread > reads\_a\_word\_(?wordread\_register-name\_word-offset\_length) > #help sysinit > writes\_the\_timing\_ctl\_register\_that\_resets\_the\_entire\_system\_(?sysinit) > #help write > write\_a\_given\_payload\_to\_an\_offset\_in\_a\_register\_(?write\_register-name\_register-offset\_data-payload) > #help bulkread > reads\_a\_given\_number\_of\_bytes\_from\_an\_offset\_in\_a\_register\_in\_a\_form\_suitable\_for\_large\_transfers\_(?bulkread\_register-name\_[register-offset\_[byte-count]]) > #help read > reads\_a\_given\_number\_of\_bytes\_from\_an\_offset\_in\_a\_register\_(?read\_register-name\_[register-offset\_[byte-count]]) > #help echotest > basic\_network\_echo\_tester\_(?echotest\_ip-address\_echo-port\_byte-count) > #help listdev lists\_available\_registers\_(?listdev) > #help delbof deletes\_a\_gateware\_image\_(?delbof\_image-file) > #help uploadbof > upload\_a\_gateware\_image\_(?uploadbof\_net-port\_filename\_[size]) > #help listbof lists\_available\_gateware\_images\_(?listbof) > #help status reports\_if\_gateware\_has\_been\_programmed\_(?status) > #help progdev programs\_a\_gateware\_image\_(?progdev\_[image-file]) > #help mode mode\_change\_command\_(?mode\_[new-mode]) > #help watchdog pings\_the\_system\_(?watchdog) > #help log-level > sets\_the\_minimum\_reported\_log\_priority\_(?log-level\_[priority]) > #help help displays\_this\_help\_(?help\_[command]) > #help restart restarts\_the\_system\_(?restart) > #help halt shuts\_the\_system\_down\_(?halt) > !help ok 26 > > Regards > > Rolando > > > 2016-12-05 12:30 GMT-06:00 Jack Hickish <jackhick...@gmail.com>: > > Hi Rolando, > Can you telnet into the roach using the command > > telnet <roach ip address> 7147 > > You should be greeted by a welcome prompt. In the prompt, type > > ?help > > If you can paste the output of these commands in an email, maybe I can > find you a version of the katcpserver which will work (assuming that's the > problem) > > Cheers > Jack > > On Mon, 5 Dec 2016, 09:30 Rolando Paz, <flx...@gmail.com> wrote: > > Hi Jack > > I have a ROACH1 Rev.3, S/N 040433, and I'm using the file system that came > in the SD-Card to use ROACH. > > Is this what I need to update? > > Also, I am using corr-0.7.3 and katcp-0.3.4. > > What are the correct versions of corr and katcp for my ROACH? Or, should > I use casperfpga? > > Best Regard > > Rolando > > 2016-12-04 15:30 GMT-06:00 Jack Hickish <jackhick...@gmail.com>: > > Hi Rolando, > > If I had to guess, I'd say there is a problem with the version of the > python katcp/corr libraries you're using, and the version of tcpborphserver > running on your ROACH. Do you know the versions of these bits of code that > you're using? > > Cheers > Jack > > On Thu, 1 Dec 2016 at 16:52 Rolando Paz <flx...@gmail.com> wrote: > > Hello again > > I'm experimenting with the 10G port, however when I tried to run the > tut_2, the following problem arises: > > rolando@rolando-MS-7815:~/codigo_ROACH/tut2$ sudo python tut2.py > 192.168.100.2 -s > [sudo] password for rolando: > Connecting to server 192.168.100.2... ok > > ------------------------ > Programming FPGA... ok > --------------------------- > Disabling output... done > --------------------------- > Port 0 linkup: True > Port 3 linkup: True > --------------------------- > Configuring receiver core... <type 'exceptions.RuntimeError'> > ('Request tap-start failed.\n Request: ?tap-start tap0 gbe3 192.168.3.16 > 60000 02:02:C0:A8:03:10\n Reply: !tap-start fail.',) > Request tap-start failed. > Request: ?tap-start tap0 gbe3 192.168.3.16 60000 02:02:C0:A8:03:10 > Reply: !tap-start fail. > FAILURE DETECTED. Log entries: > 192.168.100.2: Starting thread Thread-1 > 192.168.100.2: #version poco-0.1 > 192.168.100.2: #build-state poco-0.2804 > 192.168.100.2: ?progdev tut2.bof > > 192.168.100.2: !progdev ok 528 > 192.168.100.2: Programming FPGA with tut2.bof... ok. > 192.168.100.2: ?write pkt_sim_enable 0 \0\0\0\0 > > 192.168.100.2: !write ok > 192.168.100.2: ?read pkt_sim_enable 0 4 > > 192.168.100.2: !read ok \0\0\0\0 > 192.168.100.2: Write 0 to register pkt_sim_enable at offset 0 ok. > 192.168.100.2: ?read gbe0_linkup 0 4 > > 192.168.100.2: !read ok \0\0\0 > 192.168.100.2: ?read gbe3_linkup 0 4 > > 192.168.100.2: !read ok \0\0\0 > 192.168.100.2: Starting tgtap driver instance for tap-start: tap0 gbe3 > 192.168.3.16 60000 02:02:C0:A8:03:10 > 192.168.100.2: ?tap-start tap0 gbe3 192.168.3.16 60000 02:02:C0:A8:03:10 > > 192.168.100.2: #log error 2416053613647 poco > register\_tap0\_seems\_unavailable > 192.168.100.2: !tap-start fail > 192.168.100.2: Request tap-start failed. > Request: ?tap-start tap0 gbe3 192.168.3.16 60000 02:02:C0:A8:03:10 > Reply: !tap-start fail. > None > rolando@rolando-MS-7815:~/codigo_ROACH/tut2$ > > > How do I solve the problem? > > I will appreciate any comments ... > > Regards > > RP > > > > >