Yes ! I assume the clock has been clocked. For convenience, I have included the output script i get after I run the initialization script.
Programming 192.168.10.2 with direct_mar_29_2017_Mar_29_1500.bof.gz... Design built for ROACH2 rev2 with 4 ADCs (ZDOK rev2) Gateware supports demux modes (using demux by 1) Resetting ADC, power cycling ADC, and reprogramming FPGA... ZDOK0 clock OK Calibrating SERDES blocks...calibrating chips ["A", "B", "C", "D"] chip A chan 1 lane 0 no good taps found chip A chan 1 lane 1 no good taps found chip A chan 2 lane 0 no good taps found chip A chan 2 lane 1 no good taps found chip A chan 3 lane 0 no good taps found chip A chan 3 lane 1 no good taps found chip A chan 4 lane 0 no good taps found chip A chan 4 lane 1 no good taps found chip B chan 1 lane 0 no good taps found chip B chan 1 lane 1 no good taps found chip B chan 2 lane 0 no good taps found chip B chan 2 lane 1 no good taps found chip B chan 3 lane 0 no good taps found chip B chan 3 lane 1 no good taps found chip B chan 4 lane 0 no good taps found chip B chan 4 lane 1 no good taps found chip C chan 1 lane 0 no good taps found chip C chan 1 lane 1 no good taps found chip C chan 2 lane 0 no good taps found chip C chan 2 lane 1 no good taps found chip C chan 3 lane 0 no good taps found chip C chan 3 lane 1 no good taps found chip C chan 4 lane 0 no good taps found chip C chan 4 lane 1 no good taps found chip D chan 1 lane 0 no good taps found chip D chan 1 lane 1 no good taps found chip D chan 2 lane 0 no good taps found chip D chan 2 lane 1 no good taps found chip D chan 3 lane 0 no good taps found chip D chan 3 lane 1 no good taps found chip D chan 4 lane 0 no good taps found chip D chan 4 lane 1 no good taps found ERROR: SERDES calibration failed for ADC A. ERROR: SERDES calibration failed for ADC B. ERROR: SERDES calibration failed for ADC C. ERROR: SERDES calibration failed for ADC D. Selecting analog inputs... Using default digital gain of 1... Done! On Wed, Mar 29, 2017 at 5:33 PM, Jack Hickish <jackhick...@gmail.com> wrote: > Further, is the board clocking OK? -- I believe the initialization script > should give feedback on whether of not the FPGA's PLL has successfully > locked to the ADC clock, and what the current measured board clock is. > > Cheers > Jack > > On Wed, 29 Mar 2017 at 14:28 Matt Dexter <mdex...@berkeley.edu> wrote: > >> Is the design and lab setup consistent with the limitations documented at >> https://casper.berkeley.edu/wiki/ADC16x250-8#ADC16_Sample_ >> Rate_vs_Virtex-6_MMCM_Limitations >> ? >> >> More information on the clock requirements may be found at >> https://casper.berkeley.edu/wiki/ADC16x250-8_coax_rev_2# >> ADC16x250-8_coax_rev_2_Inputs >> >> Matt >> >> On Wed, 29 Mar 2017, vijay kumar wrote: >> >> > Date: Wed, 29 Mar 2017 17:16:34 -0400 >> > From: vijay kumar <vijaykumar01031...@gmail.com> >> > To: casper@lists.berkeley.edu >> > Subject: [casper] ADC calibration issue >> > >> > Hello Casperites, >> > I have been working on the ROACH-2 casper for the past few months. Now >> i have started to capture values from the ADC >> > 16x250-8 block. But, when I am trying to run the initialization script, >> it gives me an error saying that "chip 'x' >> > chan 'x' lane 'x' no good taps found ". I am unable to figure out what >> might be causing this error. I would be glad >> > if I could get help from you guys. >> > >> > Thank you. >> > >> > >> > With regards >> > Vijay >> > >> > -- >> > You received this message because you are subscribed to the Google >> Groups "casper@lists.berkeley.edu" group. >> > To unsubscribe from this group and stop receiving emails from it, send >> an email to >> > casper+unsubscr...@lists.berkeley.edu. >> > To post to this group, send email to casper@lists.berkeley.edu. >> > >> > >> >> -- >> You received this message because you are subscribed to the Google Groups >> "casper@lists.berkeley.edu" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to casper+unsubscr...@lists.berkeley.edu. >> To post to this group, send email to casper@lists.berkeley.edu. >> > -- > You received this message because you are subscribed to the Google Groups " > casper@lists.berkeley.edu" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to casper+unsubscr...@lists.berkeley.edu. > To post to this group, send email to casper@lists.berkeley.edu. > -- You received this message because you are subscribed to the Google Groups "casper@lists.berkeley.edu" group. To unsubscribe from this group and stop receiving emails from it, send an email to casper+unsubscr...@lists.berkeley.edu. To post to this group, send email to casper@lists.berkeley.edu.