I shopvacced all the PCI ports and reseated it. Now it comes up! Thanks Peter!
On Sun, Jun 3, 2012 at 11:05 PM, Bryce Johnson <sie...@gmail.com> wrote: > That might make sense. Inside of case was dusty. I'll clean it out and > give it another try tomorrow. > On Jun 3, 2012 9:45 PM, "Peter C. Wallace" <p...@mesanet.com> wrote: > >> On Sun, 3 Jun 2012, Bryce Johnson wrote: >> >> > Date: Sun, 3 Jun 2012 20:30:03 -0500 >> > From: Bryce Johnson <sie...@gmail.com> >> > Reply-To: "Enhanced Machine Controller (EMC)" >> > <emc-users@lists.sourceforge.net> >> > To: "Enhanced Machine Controller (EMC)" < >> emc-users@lists.sourceforge.net> >> > Subject: [Emc-users] Got my 5i25... now trying to set it up. >> > >> > I got a mesa 5i25 with prob_rfx2 firmware. I've tried two suggestions >> to >> > try and test it out. >> > >> > I put a prob_rfx2.xml (that I got off this list from a bit back) to the >> > lib/firmware/hm2/5i25 folder as well as the .bit and .pin files. Then >> > used pncconf to configure it. I think I am understanding how to >> configure >> > it, but I got this error when I tried to start it. >> > >> > insmod: error inserting >> > '/usr/realtime-2.6.32-122-rtai/modules/linuxcnc/hm2_pci.ko': -1 Invalid >> > parameters >> > >> > Next I tried to modify the 5i20 configuration to use 5i25...just to see >> if >> > I can get it to load. (someone suggested that on a prev thread) >> Changed >> > these lines in the ini >> > >> > [HOSTMOT2] >> > DRIVER=hm2_pci >> > BOARD=5i25 >> > CONFIG="firmware=hm2/5i25/prob_rfx2.bit num_encoders=0 num_pwmgens=0 >> > num_stepgens=3" >> >> OK no firmware is supposed to be included in the config line here but >> that is >> probably not the real problem >> >> > 01:0b.0 DPIO module: Device 2718:5125 >> > [ 878.146980] hm2_pci: discovered 5i25 at 0000:01:0b.0 >> > [ 878.147037] hm2/hm2_5i25.0: invalid config name, got 'HOsTMOt2', >> >> OK this is bad, this indicates a problem on the PCI bus (Bit 21 stuck >> high) >> (DEV and SSID codes are probably OK because they are read as 16 bit >> quantites >> so dont use bit 21) >> >> I would check that the slot and edge connector are clean and perhaps try >> another slot >> >> > expected 'HOSTMOT2' >> > [ 878.147042] hm2_5i25.0: board fails HM2 registration >> >> Peter Wallace >> Mesa Electronics >> >> >> >> ------------------------------------------------------------------------------ >> Live Security Virtual Conference >> Exclusive live event will cover all the ways today's security and >> threat landscape has changed and how IT managers can respond. Discussions >> will include endpoint security, mobile security and the latest in malware >> threats. http://www.accelacomm.com/jaw/sfrnl04242012/114/50122263/ >> _______________________________________________ >> Emc-users mailing list >> Emc-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/emc-users >> > ------------------------------------------------------------------------------ Live Security Virtual Conference Exclusive live event will cover all the ways today's security and threat landscape has changed and how IT managers can respond. Discussions will include endpoint security, mobile security and the latest in malware threats. http://www.accelacomm.com/jaw/sfrnl04242012/114/50122263/ _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
