Hello Oliver,
Am Montag 13 September 2010 schrieb oliver.ha...@semikron.com: > Hello, > > I have some questions about the installation of the EtherCAT-Master > software. > > 1. Just to make sure that I get it. Can I run EtherCAT-Master with the > following NIC? (Real-Time capabilities is not needed). Do I have to use a > generic Ethernet driver? > Yes, you can with the generic driver. You can use Real-Time capabilities with preempt-rt and the generic driver. > 26: PCI 304.1: 0200 Ethernet controller > [Created at pci.318] > UDI: /org/freedesktop/Hal/devices/pci_14e4_1678_0 > Unique ID: DkES._ObA2GyJda8 > Parent ID: B35A.ia5804xsnuD > SysFS ID: /devices/pci0000:00/0000:00:1c.4/0000:02:00.0/0000:03:04.1 > SysFS BusID: 0000:03:04.1 > Hardware Class: network > Model: "Broadcom NetXtreme BCM5715 Gigabit Ethernet" > Vendor: pci 0x14e4 "Broadcom" > Device: pci 0x1678 "NetXtreme BCM5715 Gigabit Ethernet" > SubVendor: pci 0x1734 "Fujitsu Technology Solutions" > SubDevice: pci 0x108c > Revision: 0xa3 > Driver: "tg3" > Driver Modules: "tg3" > Device File: eth3 > Memory Range: 0xdf930000-0xdf93ffff (rw,non-prefetchable) > Memory Range: 0xdf920000-0xdf92ffff (rw,non-prefetchable) > IRQ: 17 (no events) > HW Address: 00:26:2d:01:85:cd > Link detected: yes > Module Alias: "pci:v000014E4d00001678sv00001734sd0000108Cbc02sc00i00" > Driver Info #0: > Driver Status: tg3 is active > Driver Activation Cmd: "modprobe tg3" > Config Status: cfg=no, avail=yes, need=no, active=unknown > Attached to: #24 (PCI bridge) > > > 2. Running the configure-shell causes an error message (missing kernel > sources), but I would like to keep my kernel version (Linux primergy-llw1 > 2.6.31.5-0.1-desktop #1 SMP PREEMPT 2009-10-26 15:49:03 +0100 i686 i686 > i386 GNU/Linux). Are there any possibilities to achieve this? I've heard > the EtherCAT-Master 1.5 is still running successfully, but isn't released > now. Can I get this version? Is that version (1.5) still compatible with > the other existent software? You can use your kernel version, but you have to install the kernel header. Configure with ./configure --enable-generic --disable-8139too --with-linux-dir=your_path_to_kernel_header > Greatings Andreas > Best Regards > Oliver Haala > > IMPORTANT NOTICE - The contents of this email and attachments are > confidential. If you are not the intended recipient you must not use, copy, > distribute or rely on this email and should please return it immediately or > notify us by telephone. While we take every reasonable precaution to screen > out computer viruses from emails, attachments to this email may contain > such viruses. We cannot accept liability for loss or damage resulting from > such viruses. The integrity of email across the Internet cannot be > guaranteed and SEMIKRON will not accept liability for any claims arising as > a result of the use of this medium for transmissions by or to SEMIKRON. > _______________________________________________ > etherlab-users mailing list > etherlab-users@etherlab.org > http://lists.etherlab.org/mailman/listinfo/etherlab-users _______________________________________________ etherlab-users mailing list etherlab-users@etherlab.org http://lists.etherlab.org/mailman/listinfo/etherlab-users