So don’t errors like this suggest replacing the hardware?
Frank From: foundry-nsp [mailto:foundry-nsp-boun...@puck.nether.net] On Behalf Of Brad Fleming Sent: Tuesday, February 17, 2015 3:10 PM To: Josh Galvez Cc: foundry-nsp@puck.nether.net Subject: Re: [f-nsp] MLX throughput issues The common symptoms for us are alarms of TM errors / resets. We’ve been told on multiple TAC cases that logs indicating transmit TM errors are likely caused by problems in one of the SFM links / lanes. We’ve been told that resetting the SFMs one at a time will clear the issue. Symptoms during the issue is that 1/3rd of the traffic moving from one TM to another TM will simply get dropped. So we see TCP globally start to throttle like crazy and if enough errors count up the TM will simply reset. After the TM reset is seems a 50/50 chance the box will remain stable or go back to dropping packets within ~20mins. So when we see a TM reset we simply do the SFM Dance no matter what. On Feb 16, 2015, at 10:08 PM, Josh Galvez <j...@zevlag.com <mailto:j...@zevlag.com> > wrote: Why kind of wigout? And how do you diagnose the corruption? I'm intrigued. On Mon, Feb 16, 2015 at 8:43 AM, Brad Fleming <bdfle...@gmail.com <mailto:bdfle...@gmail.com> > wrote: We’ve seen it since installing the high-capacity switch fabrics into our XMR4000 chassis roughly 4 years ago. We saw it through IronWare 5.4.00d. I’m not sure what software we were using when they were first installed; probably whatever would have been stable/popular around December 2010. Command is simply “power-off snm [1-3]” then “power-on snm [1-3]”. Note that the power-on process causes your management session to hang for a few seconds. The device isn’t broken and packets aren’t getting dropped; it’s just going through checks and echoing back status. -brad > On Feb 16, 2015, at 7:07 AM, Jethro R Binks <jethro.bi...@strath.ac.uk > <mailto:jethro.bi...@strath.ac.uk> > wrote: > > On Fri, 13 Feb 2015, Brad Fleming wrote: > >> Over the years we’ve seen odd issues where one of the >> switch-fabric-links will “wigout” and some of the data moving between >> cards will get corrupted. When this happens we power cycle each switch >> fab one at a time using this process: >> >> 1) Shutdown SFM #3 >> 2) Wait 1 minute >> 3) Power SFM #3 on again >> 4) Verify all SFM links are up to SFM#3 >> 5) Wait 1 minute >> 6) Perform steps 1-5 for SFM #2 >> 7) Perform steps 1-5 for SFM #3 >> >> Not sure you’re seeing the same issue that we see but the “SFM Dance” >> (as we call it) is a once-every-four-months thing somewhere across our >> 16 XMR4000 boxes. It can be done with little to no impact if you are >> patient verify status before moving to the next SFM. > > That's all interesting. What code versions is this? Also, how do you > shutdown the SFMs? I don't recall seeing documentation for that. > > Jethro. > > >> >>> On Feb 13, 2015, at 11:41 AM, net...@gmail.com <mailto:net...@gmail.com> >>> wrote: >>> >>> We have three switch fabrics installed, all are under 1% utilized. >>> >>> >>> From: Jeroen Wunnink | Hibernia Networks [mailto:jeroen.wunn...@atrato.com >>> <mailto:jeroen.wunn...@atrato.com> <mailto:jeroen.wunn...@atrato.com >>> <mailto:jeroen.wunn...@atrato.com> >] >>> Sent: Friday, February 13, 2015 12:27 PM >>> To: net...@gmail.com <mailto:net...@gmail.com> <mailto:net...@gmail.com >>> <mailto:net...@gmail.com> >; 'Jeroen Wunnink | Hibernia Networks' >>> Subject: Re: [f-nsp] MLX throughput issues >>> >>> How many switchfabrics do you have in that MLX and how high is the >>> utilization on them >>> >>> On 13/02/15 18:12, net...@gmail.com <mailto:net...@gmail.com> >>> <mailto:net...@gmail.com <mailto:net...@gmail.com> > wrote: >>>> We also tested with a spare Quanta LB4M we have and are seeing about the >>>> same speeds as we are seeing with the FLS648 (around 20MB/s or 160Mbps). >>>> >>>> I also reduced the number of routes we are accepting down to about 189K >>>> and that did not make a difference. >>>> >>>> >>>> From: foundry-nsp [mailto:foundry-nsp-boun...@puck.nether.net >>>> <mailto:foundry-nsp-boun...@puck.nether.net> >>>> <mailto:foundry-nsp-boun...@puck.nether.net >>>> <mailto:foundry-nsp-boun...@puck.nether.net> >] On Behalf Of Jeroen >>>> Wunnink | Hibernia Networks >>>> Sent: Friday, February 13, 2015 3:35 AM >>>> To: foundry-nsp@puck.nether.net <mailto:foundry-nsp@puck.nether.net> >>>> <mailto:foundry-nsp@puck.nether.net <mailto:foundry-nsp@puck.nether.net> > >>>> Subject: Re: [f-nsp] MLX throughput issues >>>> >>>> The FLS switches do something weird with packets. I've noticed they >>>> somehow interfere with changing the MSS window size dynamically, resulting >>>> in destinations further away having very poor speed results compared to >>>> destinations close by. >>>> >>>> We got rid of those a while ago. >>>> >>>> >>>> On 12/02/15 17:37, net...@gmail.com <mailto:net...@gmail.com> >>>> <mailto:net...@gmail.com <mailto:net...@gmail.com> > wrote: >>>>> We are having a strange issue on our MLX running code 5.6.00c. We are >>>>> encountering some throughput issues that seem to be randomly impacting >>>>> specific networks. >>>>> >>>>> We use the MLX to handle both external BGP and internal VLAN routing. >>>>> Each FLS648 is used for Layer 2 VLANs only. >>>>> >>>>> From a server connected by 1 Gbps uplink to a Foundry FLS648 switch, >>>>> which is then connected to the MLX on a 10 Gbps port, running a speed >>>>> test to an external network is getting 20MB/s. >>>>> >>>>> Connecting the same server directly to the MLX is getting 70MB/s. >>>>> >>>>> Connecting the same server to one of my customer's Juniper EX3200 (which >>>>> BGP peers with the MLX) also gets 70MB/s. >>>>> >>>>> Testing to another external network, all three scenarios get 110MB/s. >>>>> >>>>> The path to both test network locations goes through the same IP transit >>>>> provider. >>>>> >>>>> We are running NI-MLX-MR with 2GB RAM, NI-MLX-10Gx4 connect to the >>>>> Foundry FLS648 by XFP-10G-LR, NI-MLX-1Gx20-GC was used for directly >>>>> connecting the server. A separate NI-MLX-10Gx4 connects to our upstream >>>>> BGP providers. Customer’s Juniper EX3200 connects to the same >>>>> NI-MLX-10Gx4 as the FLS648. We take default routes plus full tables from >>>>> three providers by BGP, but filter out most of the routes. >>>>> >>>>> The fiber and optics on everything look fine. CPU usage is less than 10% >>>>> on the MLX and all line cards and CPU usage at 1% on the FLS648. ARP >>>>> table on the MLX is about 12K, and BGP table is about 308K routes. >>>>> >>>>> Any assistance would be appreciated. I suspect there is a setting that >>>>> we’re missing on the MLX that is causing this issue. >>>>> >>>>> >>>>> >>>>> >>>>> _______________________________________________ >>>>> foundry-nsp mailing list >>>>> foundry-nsp@puck.nether.net <mailto:foundry-nsp@puck.nether.net> >>>>> <mailto:foundry-nsp@puck.nether.net <mailto:foundry-nsp@puck.nether.net> > >>>>> http://puck.nether.net/mailman/listinfo/foundry-nsp >>>>> <http://puck.nether.net/mailman/listinfo/foundry-nsp> >>>> >>>> >>>> >>>> -- >>>> >>>> Jeroen Wunnink >>>> IP NOC Manager - Hibernia Networks >>>> Main numbers (Ext: 1011): USA +1.908.516.4200 <tel:%2B1.908.516.4200> | >>>> UK +44.1704.322.300 <tel:%2B44.1704.322.300> >>>> Netherlands +31.208.200.622 <tel:%2B31.208.200.622> | 24/7 IP NOC Phone: >>>> +31.20.82.00.623 <tel:%2B31.20.82.00.623> >>>> jeroen.wunn...@hibernianetworks.com >>>> <mailto:jeroen.wunn...@hibernianetworks.com> >>>> <mailto:jeroen.wunn...@hibernianetworks.com >>>> <mailto:jeroen.wunn...@hibernianetworks.com> > >>>> www.hibernianetworks.com <http://www.hibernianetworks.com/> >>>> <http://www.hibernianetworks.com/> >>> >>> >>> -- >>> >>> Jeroen Wunnink >>> IP NOC Manager - Hibernia Networks >>> Main numbers (Ext: 1011): USA +1.908.516.4200 <tel:%2B1.908.516.4200> | UK >>> +44.1704.322.300 <tel:%2B44.1704.322.300> >>> Netherlands +31.208.200.622 <tel:%2B31.208.200.622> | 24/7 IP NOC Phone: >>> +31.20.82.00.623 <tel:%2B31.20.82.00.623> >>> jeroen.wunn...@hibernianetworks.com >>> <mailto:jeroen.wunn...@hibernianetworks.com> >>> <mailto:jeroen.wunn...@hibernianetworks.com >>> <mailto:jeroen.wunn...@hibernianetworks.com> > >>> www.hibernianetworks.com <http://www.hibernianetworks.com/> >>> <http://www.hibernianetworks.com/>_______________________________________________ >>> foundry-nsp mailing list >>> foundry-nsp@puck.nether.net <mailto:foundry-nsp@puck.nether.net> >>> <mailto:foundry-nsp@puck.nether.net <mailto:foundry-nsp@puck.nether.net> > >>> http://puck.nether.net/mailman/listinfo/foundry-nsp >>> <http://puck.nether.net/mailman/listinfo/foundry-nsp> >> > > . . . . . . . . . . . . . . . . . . . . . . . . . > Jethro R Binks, Network Manager, > Information Services Directorate, University Of Strathclyde, Glasgow, UK > > The University of Strathclyde is a charitable body, registered in > Scotland, number SC015263. _______________________________________________ foundry-nsp mailing list foundry-nsp@puck.nether.net <mailto:foundry-nsp@puck.nether.net> http://puck.nether.net/mailman/listinfo/foundry-nsp
_______________________________________________ foundry-nsp mailing list foundry-nsp@puck.nether.net http://puck.nether.net/mailman/listinfo/foundry-nsp
