Good script -- I would use it 'after' the move though - not before..
backout is much easier that way... make changes on the new dasd - not the
old.
Use SAPL and change PDVOL= to correct address... 'then' run this script
once everything comes up and looks good. IMHO.
Scott Rohling
On Thu, Aug 16, 2018 at 4:16 PM Davis, Larry (National VM Capability) <
larry.dav...@dxc.com> wrote:
> For that process to work you will have to load a new Standalone program
> Loader using the new Device address for the PDR volume on the PDVOL =xxxx
>
> Here is an example of an exec to load the IPL SALIPL file from the MAINT
> 190 "S" disk
>
> MKSAIPL EXEC:
> /* rexx exec */
>
> true = (1=1)
> false = \true
> debug = TRUE
>
> /* **************************************************************** */
> /* */
> /* Setup Procedures: */
> /* 1 NEED ACCESS TO THE Z/VM 6.4 IPL SALIPL TEXT DECK */
> /* 2 If this is SSI Environment set to TRUE otherwise FALSE */
> /* 3 Is the virtual address the address the RESVOL is linked as? */
> /* 4 Is the volid of the RESVOL? */
> /* 5 Is the real address of the PDR VOLUME? */
> /* */
> /* **************************************************************** */
>
> ssi = FALSE /* Set to TRUE when using SSI */
> DEV_ADDR = 'xxxx' /* RESVOL Virtual Address */
> VOL_ID = 'vvvvvv' /* RESVOL Volume Serial Number */
> PD_VOL = 'xxxx' /* PDR VOLUME Real Address */
>
> /* *************************************************** */
> /* PDNUM is the offset extent for the CF0 PARM disk */
> /* PDVOL is the Real address for the PDR Volume */
> /* *************************************************** */
>
> if ssi Then do
> Say
> Say 'Loading SALIPL text deck for SSI on RESVOL' vol_id 'on' dev_addr
> Say
> IPL_PARM = 'FN=SYSTEM FT=CONFIG PDNUM=1 PDVOL=' pd_vol end Else do
> Say
> Say 'Loading SALIPL text deck on RESVOL' vol_id 'on' dev_addr
> Say
> IPL_PARM = 'FN=SYSTEM FT=CONFIG'
> end
>
> if debug then do
> salp_opt = 'EXTENT 1 VOLID' vol_id ,
> 'IPLPARMS' ipl_parm
> say ' ADDRESS COMMAND SALIPL' dev_addr
> say ' (' salp_opt
> end
> else do
> salp_opt = 'EXTENT 1 VOLID' vol_id ,
> 'COMMENTS ? IPLPARMS' ipl_parm
>
> queue 'IPL Parameters Options are: '
> queue ' CONS=xxxx FN=fn FT=ft CLEARPDR REPAIR NOEXITS NOHCD PROMPT'
> queue ' PDNUM=n PDOFF=offset PDVOL=addr STORE=nnnnM/G/T/P/E '
> queue
>
> ADDRESS COMMAND 'SALIPL' dev_addr '(' salp_opt end
>
> Exit
>
>
>
> Larry Davis
>
>
> -----Original Message-----
> From: Linux on 390 Port [mailto:LINUX-390@VM.MARIST.EDU] On Behalf Of
> Davis, Jim [PRI-1PP]
> Sent: Thursday, August 16, 2018 17:54
> To: LINUX-390@VM.MARIST.EDU
> Subject: Re: Moving z/vm and zlinux volumes from old dasd to new dasd
>
> Thanks for the info. I get the following.
>
> Current IPL parameters:
> FN=SYSTEM FT=CONFIG PDNUM=1 PDVOL=A84C
> CONS=0908
>
> The PDVOL points to common volume which contains the SYSTEM CONFIG file.
>
> I wonder if I can
> Change PDVOL to the new address for the common volume.
> Shutdown
> Move all six volumes to their new addresses.
> IPL from new res volume address.
>
>
> -----Original Message-----
> From: Linux on 390 Port <LINUX-390@VM.MARIST.EDU> On Behalf Of Tom Huegel
> Sent: Thursday, August 16, 2018 5:36 PM
> To: LINUX-390@VM.MARIST.EDU
> Subject: Re: Moving z/vm and zlinux volumes from old dasd to new dasd
>
> Last question Q IPLPARMS
>
>
> On Thu, Aug 16, 2018 at 4:14 PM, Davis, Jim [PRI-1PP] <
> jim.da...@primerica.com> wrote:
>
> > I have been tasked with moving our z/VM and zlinux file system volume
> > from an old DASD system to a New DASD system.
> > All of my device numbers / unit addresses will change.
> >
> > I have been successful in moving all of the z/linux volumes.
> >
> > My problem is how to move the 6 VM volumes since the IPL text has unit
> > addresses in it.
> >
> > In z/vm 5.x I just zapped the 2 addresses in ipl text.
> >
> > In z/VM 6.4 the ipl text has all of 6 volume address in text and some
> > in hex.
> >
> > Can I use SALIPL to change these addresses?
> >
> > SALIPL was run under the covers when I installed VM6.4; Is there a way
> > to find out what was passed as parms to SALIPL.
> >
> >
> >
> > James Davis
> > jim.da...@primerica.com
> > 470-564-5061
> > "quando omni flunkus moritati"
> >
> > ----------------------------------------------------------------------
> > For LINUX-390 subscribe / signoff / archive access instructions, send
> > email to lists...@vm.marist.edu with the message: INFO LINUX-390 or
> > visit
> > http://www.marist.edu/htbin/wlvindex?LINUX-390
> > ----------------------------------------------------------------------
> > For more information on Linux on System z, visit
> > http://wiki.linuxvm.org/
> >
>
> ----------------------------------------------------------------------
> For LINUX-390 subscribe / signoff / archive access instructions, send
> email to lists...@vm.marist.edu with the message: INFO LINUX-390 or visit
> http://www.marist.edu/htbin/wlvindex?LINUX-390
> ----------------------------------------------------------------------
> For more information on Linux on System z, visit http://wiki.linuxvm.org/
>
> ----------------------------------------------------------------------
> For LINUX-390 subscribe / signoff / archive access instructions, send
> email to lists...@vm.marist.edu with the message: INFO LINUX-390 or visit
> http://www.marist.edu/htbin/wlvindex?LINUX-390
> ----------------------------------------------------------------------
> For more information on Linux on System z, visit http://wiki.linuxvm.org/
>
>
> DXC - This is a PRIVATE message - If you are not the intended recipient,
> please delete without copying and kindly advise us by e-mail of the mistake
> in delivery. NOTE: Regardless of content, this e-mail shall not operate to
> bind the Company to any order or other contract unless pursuant to explicit
> written agreement or government initiative expressly permitting the use of
> e-mail for such purpose.
>
> ----------------------------------------------------------------------
> For LINUX-390 subscribe / signoff / archive access instructions,
> send email to lists...@vm.marist.edu with the message: INFO LINUX-390 or
> visit
> http://www.marist.edu/htbin/wlvindex?LINUX-390
> ----------------------------------------------------------------------
> For more information on Linux on System z, visit
> http://wiki.linuxvm.org/
>
----------------------------------------------------------------------
For LINUX-390 subscribe / signoff / archive access instructions,
send email to lists...@vm.marist.edu with the message: INFO LINUX-390 or visit
http://www.marist.edu/htbin/wlvindex?LINUX-390
----------------------------------------------------------------------
For more information on Linux on System z, visit
http://wiki.linuxvm.org/
