[The previous replay mysteriously didn't include Eric in To:, sorry,
quoting whole message here.]
Tejun Heo wrote:
> Hello, Eric.
>
> Eric D. Mudama wrote:
>> Per Jeff's suggestion, this patch rearranges the info printed for ATA
>> drives into dmesg to add the full ATA firmware revision and model
>> information, while keeping the output to 2 lines.
>>
>> Signed-off-by: Eric D. Mudama <[EMAIL PROTECTED]>
>
> The patch is formatted and applies perfectly. I'm glad to see this
> change. Just a few nits below.
>
>> char revbuf[7]; /* XYZ-99\0 */
>> + char fwrevbuf[9];
>> + char modelbuf[41];
>
> Please use ATA_ID_FW_REV_LEN + 1 and ATA_ID_PROD_LEN + 1.
This depends on to which version this patch applies. For
#upstream-fixes (2.6.20-rc6), you have to use raw numbers as you did.
For #upstream, there are above two constants to use. I think this patch
is good for 2.6.20 as it's safe && will help us analyzing bug reports
for 2.6.20. So, ignore this part of the comment.
Jeff, if it gets merged into #upstream through #upstream-fixes, please
don't forget to change above constants.
>> @@ -1680,13 +1692,18 @@ int ata_dev_configure(struct ata_device *dev)
>> ata_dev_config_ncq(dev, ncq_desc, sizeof(ncq_desc));
>>
>> /* print device info to dmesg */
>> - if (ata_msg_drv(ap) && print_info)
>> - ata_dev_printk(dev, KERN_INFO, "%s, "
>> - "max %s, %Lu sectors: %s %s\n",
>> + if (ata_msg_drv(ap) && print_info) {
>> + ata_dev_printk(dev, KERN_INFO,
>> + "%s: %s, %s, max %s\n",
>> revbuf,
>> - ata_mode_string(xfer_mask),
>> + modelbuf, fwrevbuf,
>
> Please merge the above line with the line above it.
>
>> + ata_mode_string(xfer_mask));
>> + ata_dev_printk(dev, KERN_INFO,
>> + "%Lu sectors, multi %u: %s %s\n",
>> (unsigned long long)dev->n_sectors,
>> + dev->multi_count,
>> lba_desc, ncq_desc);
>
> Ditto.
>
>> + }
>> } else {
>> /* CHS */
>>
>> @@ -1703,22 +1720,19 @@ int ata_dev_configure(struct ata_device *dev)
>> }
>>
>> /* print device info to dmesg */
>> - if (ata_msg_drv(ap) && print_info)
>> - ata_dev_printk(dev, KERN_INFO, "%s, "
>> - "max %s, %Lu sectors: CHS %u/%u/%u\n",
>> + if (ata_msg_drv(ap) && print_info) {
>> + ata_dev_printk(dev, KERN_INFO,
>> + "%s: %s, %s, max %s\n",
>> revbuf,
>> - ata_mode_string(xfer_mask),
>> + modelbuf, fwrevbuf,
>
> Ditto.
>
>> + ata_mode_string(xfer_mask));
>> + ata_dev_printk(dev, KERN_INFO,
>> + "%Lu sectors, multi %u, CHS %u/%u/%u\n",
>> (unsigned long long)dev->n_sectors,
>> + dev->multi_count,
>> dev->cylinders, dev->heads,
>> dev->sectors);
>
> I would prefer
>
> dev->multi_count, dev->cylinders,
> dev->heads, dev->sectors
>
> Other than these,
>
> Acked-by: Tejun Heo <[EMAIL PROTECTED]>
>
--
tejun
-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
