Thanks Rob for review, find answers below.
On 04/03/2017 06:23 PM, Rob Herring wrote:
> On Thu, Mar 30, 2017 at 05:27:40PM +0200, Hugues Fruchet wrote:
>> This adds documentation of device tree bindings for the STM32 DCMI
>> (Digital Camera Memory Interface).
>>
>> Signed-off-by: Hugues Fruchet <hugues.fruc...@st.com>
>> ---
>> .../devicetree/bindings/media/st,stm32-dcmi.txt | 85
>> ++++++++++++++++++++++
>> 1 file changed, 85 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/media/st,stm32-dcmi.txt
>>
>> diff --git a/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt
>> b/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt
>> new file mode 100644
>> index 0000000..8180f63
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt
>> @@ -0,0 +1,85 @@
>> +STMicroelectronics STM32 Digital Camera Memory Interface (DCMI)
>> +
>> +Required properties:
>> +- compatible: "st,stm32-dcmi"
>
> Same block and same errata on all stm32 variants?
Yes, it is the same IP block on all stm32 variants.
>
>> +- reg: physical base address and length of the registers set for the device
>> +- interrupts: should contain IRQ line for the DCMI
>> +- clocks: list of clock specifiers, corresponding to entries in
>> + the clock-names property
>> +- clock-names: must contain "mclk", which is the DCMI peripherial clock
>> +- resets: reference to a reset controller
>> +- reset-names: see Documentation/devicetree/bindings/reset/st,stm32-rcc.txt
>> +
>> +DCMI supports a single port node with parallel bus. It should contain one
>> +'port' child node with child 'endpoint' node. Please refer to the bindings
>> +defined in Documentation/devicetree/bindings/media/video-interfaces.txt.
>> +
>> +Example:
>> +
>> +Device node example
>> +-------------------
>> + dcmi: dcmi@50050000 {
>> + compatible = "st,stm32-dcmi";
>> + reg = <0x50050000 0x400>;
>> + interrupts = <78>;
>> + resets = <&rcc STM32F4_AHB2_RESET(DCMI)>;
>> + clocks = <&rcc 0 STM32F4_AHB2_CLOCK(DCMI)>;
>> + clock-names = "mclk";
>
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&dcmi_pins>;
>
> Not documented.
Fixed in v3.
>
>> + dmas = <&dma2 1 1 0x414 0x3>;
>> + dma-names = "tx";
>
> Not documented.
Fixed in v3.
>
>> + status = "disabled";
>
> Drop status from examples.
Fixed in v3.
>
>> + };
>> +
>> +Board setup example
>
> Please don't split examples. That's just source level details and not
> part of the ABI.
Fixed in v3.
>
>> +-------------------
>> +This example is extracted from STM32F429-EVAL board devicetree.
>> +Please note that on this board, the camera sensor reset & power-down
>> +line level are inverted (so reset is active high and power-down is
>> +active low).
>> +
>> +/ {
>> + [...]
>> + clocks {
>> + clk_ext_camera: clk-ext-camera {
>> + #clock-cells = <0>;
>> + compatible = "fixed-clock";
>> + clock-frequency = <24000000>;
>> + };
>> + };
>> + [...]
>> +};
>> +
>> +&dcmi {
>> + status = "okay";
>> +
>> + port {
>> + dcmi_0: endpoint@0 {
>> + remote-endpoint = <&ov2640_0>;
>> + bus-width = <8>;
>> + hsync-active = <0>;
>> + vsync-active = <0>;
>> + pclk-sample = <1>;
>> + };
>> + };
>> +};
>> +
>> +&i2c@1 {
>> + [...]
>> + ov2640: camera@30 {
>> + compatible = "ovti,ov2640";
>> + reg = <0x30>;
>> + resetb-gpios = <&stmpegpio 2 GPIO_ACTIVE_HIGH>;
>> + pwdn-gpios = <&stmpegpio 0 GPIO_ACTIVE_LOW>;
>> + clocks = <&clk_ext_camera>;
>> + clock-names = "xvclk";
>> + status = "okay";
>> +
>> + port {
>> + ov2640_0: endpoint {
>> + remote-endpoint = <&dcmi_0>;
>> + };
>> + };
>> + };
>> +};
>> --
>> 1.9.1
>>
