Hi Alexandre, As you are planning a clock binding rework and this patch in the series needs a change to account for that, do you want me to re-submit after your series or are we good to go as is?
Thanks, Ben > This adds support for Lairds CPU module, featuring Atheros wifi, CSR > Bluetooth and, Atmel SAMA5D3 CPU. > https://www.lairdtech.com/products/wb50nbt-wi-fi-bluetooth-module > > Signed-off-by: Ben Whitten <ben.whit...@lairdtech.com> > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/at91-wb50n.dts | 112 +++++++++++++++++++++ > arch/arm/boot/dts/at91-wb50n.dtsi | 198 > ++++++++++++++++++++++++++++++++++++++ > 3 files changed, 311 insertions(+) > create mode 100644 arch/arm/boot/dts/at91-wb50n.dts > create mode 100644 arch/arm/boot/dts/at91-wb50n.dtsi > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 04604d2..07823be 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -52,6 +52,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \ > at91-sama5d2_xplained.dtb \ > at91-sama5d3_xplained.dtb \ > at91-tse850-3.dtb \ > + at91-wb50n.dtb \ > sama5d31ek.dtb \ > sama5d33ek.dtb \ > sama5d34ek.dtb \ > diff --git a/arch/arm/boot/dts/at91-wb50n.dts b/arch/arm/boot/dts/at91- > wb50n.dts > new file mode 100644 > index 0000000..8cecc70 > --- /dev/null > +++ b/arch/arm/boot/dts/at91-wb50n.dts > @@ -0,0 +1,112 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * at91-wb50n.dts - Device Tree file for wb50n evaluation board > + * > + * Copyright (C) 2018 Laird > + * > + */ > + > +/dts-v1/; > +#include "at91-wb50n.dtsi" > + > +/ { > + model = "Laird Workgroup Bridge 50N - Atmel SAMA5D"; > + compatible = "laird,wb50n", "atmel,sama5d31", "atmel,sama5d3", > "atmel,sama5"; > + > + gpio_keys { > + compatible = "gpio-keys"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + btn0@10 { > + reg = <10>; > + label = "BTNESC"; > + linux,code = <1>; /* ESC button */ > + gpios = <&pioA 10 GPIO_ACTIVE_LOW>; > + gpio-key,wakeup = <1>; > + }; > + > + irqbtn@31 { > + reg = <31>; > + label = "IRQBTN"; > + linux,code = <99>; /* SysReq button */ > + gpios = <&pioE 31 GPIO_ACTIVE_LOW>; > + gpio-key,wakeup = <1>; > + }; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + led0 { > + label = "wb50n:blue:led0"; > + gpios = <&pioA 12 GPIO_ACTIVE_LOW>; > + default-state = "off"; > + }; > + > + led1 { > + label = "wb50n:green:led1"; > + gpios = <&pioA 24 GPIO_ACTIVE_LOW>; > + default-state = "off"; > + }; > + > + led2 { > + label = "wb50n:red:led2"; > + gpios = <&pioA 26 GPIO_ACTIVE_LOW>; > + default-state = "off"; > + }; > + }; > +}; > + > +&watchdog { > + status = "okay"; > +}; > + > +&mmc0 { > + status = "okay"; > +}; > + > +&macb1 { > + status = "okay"; > +}; > + > +&dbgu { > + status = "okay"; > +}; > + > +/* On BB40 this port is labeled UART1 */ > +&usart0 { > + status = "okay"; > +}; > + > +/* On BB40 this port is labeled UART0 */ > +&usart1 { > + status = "okay"; > +}; > + > +&i2c0 { > + status = "okay"; > +}; > + > +&spi1 { > + status = "okay"; > + > + spidev@0 { > + compatible = "spidev"; > + reg = <0>; > + spi-max-frequency = <8000000>; > + }; > +}; > + > +&usb0 { > + status = "okay"; > +}; > + > +&usb1 { > + status = "okay"; > +}; > + > +&usb2 { > + status = "okay"; > +}; > + > diff --git a/arch/arm/boot/dts/at91-wb50n.dtsi b/arch/arm/boot/dts/at91- > wb50n.dtsi > new file mode 100644 > index 0000000..85692c8 > --- /dev/null > +++ b/arch/arm/boot/dts/at91-wb50n.dtsi > @@ -0,0 +1,198 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * at91-wb50n.dtsi - Device Tree include file for wb50n cpu module > + * > + * Copyright (C) 2018 Laird > + * > + */ > + > +#include "sama5d31.dtsi" > + > +/ { > + model = "Laird Workgroup Bridge 50N - Atmel SAMA5D"; > + compatible = "laird,wb50n", "atmel,sama5d31", "atmel,sama5d3", > "atmel,sama5"; > + > + chosen { > + bootargs = "ubi.mtd=6 root=ubi0:rootfs rootfstype=ubifs > rw"; > + stdout-path = "serial0:115200n8"; > + }; > + > + memory { > + reg = <0x20000000 0x4000000>; > + }; > +}; > + > +&pinctrl { > + board { > + pinctrl_mmc0_cd: mmc0_cd { > + atmel,pins = <AT91_PIOC 26 AT91_PERIPH_GPIO > AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PC26 GPIO with pullup deglitch */ > + }; > + > + pinctrl_usba_vbus: usba_vbus { > + atmel,pins = <AT91_PIOB 13 AT91_PERIPH_GPIO > AT91_PINCTRL_DEGLITCH>; /* PB13 GPIO with deglitch */ > + }; > + }; > +}; > + > +&slow_xtal { > + clock-frequency = <32768>; > +}; > + > +&main_xtal { > + clock-frequency = <12000000>; > +}; > + > +&slow_osc { > + atmel,osc-bypass; > +}; > + > +&usart1_clk { > + atmel,clk-output-range = <0 132000000>; > +}; > + > +&mmc0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 > &pinctrl_mmc0_cd>; > + cd-gpios = <&pioC 26 GPIO_ACTIVE_LOW>; > + slot@0 { > + reg = <0>; > + bus-width = <4>; > + }; > +}; > + > +&mmc1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3>; > + status = "okay"; > + atheros@0 { > + compatible = "atheros,ath6kl"; > + atheros,board-id = "SD32"; > + reg = <0>; > + bus-width = <4>; > + }; > +}; > + > +&macb1 { > + phy-mode = "rmii"; > +}; > + > +&dbgu { > + dmas = <0>, <0>; /* Do not use DMA for dbgu */ > +}; > + > +/* On BB40 this port is labeled UART1 */ > +&usart0 { > + atmel,use-dma-rx; > + atmel,use-dma-tx; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usart0 &pinctrl_usart0_rts_cts>; > +}; > + > +/* On BB40 this port is labeled UART0 */ > +&usart1 { > + atmel,use-dma-rx; > + atmel,use-dma-tx; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>; > + dtr-gpios = <&pioD 13 GPIO_ACTIVE_LOW>; > + dsr-gpios = <&pioD 11 GPIO_ACTIVE_LOW>; > + dcd-gpios = <&pioD 7 GPIO_ACTIVE_LOW>; > + rng-gpios = <&pioD 8 GPIO_ACTIVE_LOW>; > +}; > + > +/* USART3 is direct-connect to the Bluetooth UART on the radio SIP */ > +&usart3 { > + atmel,use-dma-rx; > + atmel,use-dma-tx; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usart3 &pinctrl_usart3_rts_cts>; > + status = "okay"; > +}; > + > +&spi1 { > + cs-gpios = <&pioC 25 0>, <0>, <0>, <0>; > +}; > + > +&ebi { > + pinctrl-0 = <&pinctrl_ebi_nand_addr>; > + pinctrl-names = "default"; > + status = "okay"; > +}; > + > +&nand_controller { > + status = "okay"; > + > + nand: nand@3 { > + reg = <0x3 0x0 0x2>; > + atmel,rb = <0>; > + nand-bus-width = <8>; > + nand-ecc-mode = "hw"; > + nand-ecc-strength = <8>; > + nand-ecc-step-size = <512>; > + nand-on-flash-bbt; > + label = "atmel_nand"; > + > + partitions { > + compatible = "fixed-partitions"; > + #address-cells = <1>; > + #size-cells = <1>; > + > + at91bootstrap@0 { > + label = "at91bs"; > + reg = <0x0 0x20000>; > + }; > + > + uboot@20000 { > + label = "u-boot"; > + reg = <0x20000 0x80000>; > + }; > + > + ubootenv@a0000 { > + label = "u-boot-env"; > + reg = <0xa0000 0x20000>; > + }; > + > + ubootenv@c0000 { > + label = "u-boot-env"; > + reg = <0xc0000 0x20000>; > + }; > + > + kernel-a@e0000 { > + label = "kernel-a"; > + reg = <0xe0000 0x500000>; > + }; > + > + kernel-b@5e0000 { > + label = "kernel-b"; > + reg = <0x5e0000 0x500000>; > + }; > + > + rootfs-a@ae0000 { > + label = "rootfs-a"; > + reg = <0xae0000 0x3000000>; > + }; > + > + rootfs-b@3ae0000 { > + label = "rootfs-b"; > + reg = <0x3ae0000 0x3000000>; > + }; > + > + user@6ae0000 { > + label = "user"; > + reg = <0x6ae0000 0x14e0000>; > + }; > + }; > + }; > +}; > + > +&usb0 { > + atmel,vbus-gpio = <&pioB 13 GPIO_ACTIVE_LOW>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usba_vbus>; > +}; > + > +&usb1 { > + num-ports = <3>; > + atmel,vbus-gpio = <&pioA 2 GPIO_ACTIVE_LOW>; > + atmel,oc-gpio = <&pioA 4 GPIO_ACTIVE_LOW>; > +}; > -- > 2.7.4
