On Wed, 2015-01-14 at 17:08 -0800, Kevin Hilman wrote: > From: Kevin Hilman <khil...@linaro.org> > > The odroid-xu3 has 4 INA231 current sensors on board which can be > accessed from the Linux via the hwmon interface. > > There is one sensor for each of these power rails: > > - A15 cluster: VDD_ARM > - A7 cluster: VDD_KFC > - GPU: VDD_G3D > - memory: VDD_MEM > > In addition to adding the sensors, LDO26 from the PMIC needs to be > enabled because it's powering these sensor.
I haven't tested whether the sensor values are correct, but based on the
schematics & the hardkernel dts this describes the hardware correctly.
Reviewed-By: Sjoerd Simons <sjoerd.sim...@collabora.co.uk>
> Cc: Javier Martinez Canillas <javier.marti...@collabora.co.uk>
> Cc: Sjoerd Simons <sjoerd.sim...@collabora.co.uk>
> Signed-off-by: Kevin Hilman <khil...@linaro.org>
> ---
> v2: use "ti,ina231" as compatible string.
>
> Applies on top of "ARM: dts: Add dts file for odroid XU3 board" from Sjoerd
> Simons.
>
> arch/arm/boot/dts/exynos5422-odroidxu3.dts | 39
> ++++++++++++++++++++++++++++++
> 1 file changed, 39 insertions(+)
>
> diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3.dts
> b/arch/arm/boot/dts/exynos5422-odroidxu3.dts
> index c29123c0734d..50353d023225 100644
> --- a/arch/arm/boot/dts/exynos5422-odroidxu3.dts
> +++ b/arch/arm/boot/dts/exynos5422-odroidxu3.dts
> @@ -174,6 +174,13 @@
> regulator-always-on;
> };
>
> + ldo26_reg: LDO26 {
> + regulator-name = "vdd_ldo26";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-always-on;
> + };
> +
> buck1_reg: BUCK1 {
> regulator-name = "vdd_mif";
> regulator-min-microvolt = <800000>;
> @@ -257,6 +264,38 @@
> };
> };
>
> + i2c_0: i2c@12C60000 {
> + status = "okay";
> +
> + /* A15 cluster: VDD_ARM */
> + ina231@40 {
> + compatible = "ti,ina231";
> + reg = <0x40>;
> + shunt-resistor = <10000>;
> + };
> +
> + /* memory: VDD_MEM */
> + ina231@41 {
> + compatible = "ti,ina231";
> + reg = <0x41>;
> + shunt-resistor = <10000>;
> + };
> +
> + /* GPU: VDD_G3D */
> + ina231@44 {
> + compatible = "ti,ina231";
> + reg = <0x44>;
> + shunt-resistor = <10000>;
> + };
> +
> + /* A7 cluster: VDD_KFC */
> + ina231@45 {
> + compatible = "ti,ina231";
> + reg = <0x45>;
> + shunt-resistor = <10000>;
> + };
> + };
> +
> i2c_2: i2c@12C80000 {
> samsung,i2c-sda-delay = <100>;
> samsung,i2c-max-bus-freq = <66000>;
smime.p7s
Description: S/MIME cryptographic signature
