Adds devicetree binding documentation.
Signed-off-by: Stanimir Varbanov <svarba...@mm-sol.com>
---
.../bindings/pinctrl/qcom,msm8916-pinctrl.txt | 186 ++++++++++++++++++++
1 files changed, 186 insertions(+), 0 deletions(-)
create mode 100644
Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.txt
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.txt
b/Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.txt
new file mode 100644
index 0000000..10c2dcf
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.txt
@@ -0,0 +1,186 @@
+Qualcomm MSM8916 TLMM block
+
+This binding describes the Top Level Mode Multiplexer block found in the
+MSM8916 platform.
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be "qcom,msm8916-pinctrl"
+
+- reg:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: the base address and size of the TLMM register space.
+
+- interrupts:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: should specify the TLMM summary IRQ.
+
+- interrupt-controller:
+ Usage: required
+ Value type: <none>
+ Definition: identifies this node as an interrupt controller
+
+- #interrupt-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: must be 2. Specifying the pin number and flags, as defined
+ in <dt-bindings/interrupt-controller/irq.h>
+
+- gpio-controller:
+ Usage: required
+ Value type: <none>
+ Definition: identifies this node as a gpio controller
+
+- #gpio-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: must be 2. Specifying the pin number and flags, as defined
+ in <dt-bindings/gpio/gpio.h>
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+
+PIN CONFIGURATION NODES:
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+- pins:
+ Usage: required
+ Value type: <string-array>
+ Definition: List of gpio pins affected by the properties specified in
+ this subnode. Valid pins are:
+ gpio0-gpio121,
+ sdc1_clk,
+ sdc1_cmd,
+ sdc1_data
+ sdc2_clk,
+ sdc2_cmd,
+ sdc2_data,
+ qdsd_cmd,
+ qdsd_data0,
+ qdsd_data1,
+ qdsd_data2,
+ qdsd_data3
+
+- function:
+ Usage: required
+ Value type: <string>
+ Definition: Specify the alternative function to be configured for the
+ specified pins. Functions are only valid for gpio pins.
+ Valid values are:
+ adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char, atest_char0,
+ atest_char1, atest_char2, atest_char3, atest_combodac, atest_gpsadc0,
+ atest_gpsadc1, atest_tsens, atest_wlan0, atest_wlan1, backlight_en,
+ bimc_dte0, bimc_dte1, blsp1_spi, blsp2_spi, blsp3_spi, blsp_i2c1,
+ blsp_i2c2, blsp_i2c3, blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_spi1,
+ blsp_spi2, blsp_spi3, blsp_spi4, blsp_spi5, blsp_spi6, blsp_uart1,
+ blsp_uart2, blsp_uim1, blsp_uim2, cam1_rst, cam1_standby, cam_mclk,
+ cci_async, cci_i2c, cci_timer0, cci_timer1, cci_timer2, cdc_pdm0,
+ codec_mad, dbg_out, display_5v, dmic0_clk, dmic0_data, dsi_rst,
+ ebi0_wrcdc, euro_us, ext_lpass, flash_strobe, gcc_gp1_clk_a,
+ gcc_gp1_clk_b, gcc_gp2_clk_a, gcc_gp2_clk_b, gcc_gp3_clk_a,
+ gcc_gp3_clk_b, gpio, gsm0_tx0, gsm0_tx1, gsm1_tx0, gsm1_tx1, gyro_accl,
+ kpsns0, kpsns1, kpsns2, ldo_en, ldo_update, mag_int, mdp_vsync,
+ modem_tsync, m_voc, nav_pps, nav_tsync, pa_indicator, pbs0, pbs1, pbs2,
+ pri_mi2s, pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a,
+ pwr_crypto_enabled_b, pwr_modem_enabled_a, pwr_modem_enabled_b,
+ pwr_nav_enabled_a, pwr_nav_enabled_b, qdss_cti_trig_in_a0,
+ qdss_cti_trig_in_a1, qdss_cti_trig_in_b0, qdss_cti_trig_in_b1,
+ qdss_cti_trig_out_a0, qdss_cti_trig_out_a1, qdss_cti_trig_out_b0,
+ qdss_cti_trig_out_b1, qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a,
+ qdss_tracectl_b, qdss_tracedata_a, qdss_tracedata_b, reset_n, sd_card,
+ sd_write, sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1_clk, uim1_data,
+ uim1_present, uim1_reset, uim2_clk, uim2_data, uim2_present, uim2_reset,
+ uim3_clk, uim3_data, uim3_present, uim3_reset, uim_batt, wcss_bt,
+ wcss_fm, wcss_wlan, wcss_wlan0, wcss_wlan1, wcss_wlan2, webcam1_rst,
+
+- bias-disable:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins should be configued as no pull.
+
+- bias-pull-down:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins should be configued as pull down.
+
+- bias-pull-up:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins should be configued as pull up.
+
+- output-high:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are configured in output mode, driven
+ high.
+ Not valid for sdc pins.
+
+- output-low:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are configured in output mode, driven
+ low.
+ Not valid for sdc pins.
+
+- drive-strength:
+ Usage: optional
+ Value type: <u32>
+ Definition: Selects the drive strength for the specified pins, in mA.
+ Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
+
+Example:
+
+ tlmm: pinctrl@1000000 {
+ compatible = "qcom,msm8916-pinctrl";
+ reg = <0x1000000 0x300000>;
+ interrupts = <0 208 0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ uart2: uart2-default {
+ mux {
+ pins = "gpio4", "gpio5";
+ function = "blsp_uart2";
+ };
+
+ tx {
+ pins = "gpio4";
+ drive-strength = <4>;
+ bias-disable;
+ };
+
+ rx {
+ pins = "gpio5";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+ };
--
1.7.0.4
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
