Hi Sergio,
Thanks for the review!
Aguirre, Sergio wrote:
> On Thu, Feb 2, 2012 at 5:54 PM, Sakari Ailus <sakari.ai...@iki.fi> wrote:
>> Configure CSI-2 phy based on platform data in the ISP driver. For that, the
>> new V4L2_CID_IMAGE_SOURCE_PIXEL_RATE control is used. Previously the same
>> was configured from the board code.
>>
>> Signed-off-by: Sakari Ailus <sakari.ai...@iki.fi>
>> ---
>> drivers/media/video/omap3isp/ispcsi2.c | 10 +++-
>> drivers/media/video/omap3isp/ispcsiphy.c | 78
>> ++++++++++++++++++++++++++----
>> drivers/media/video/omap3isp/ispcsiphy.h | 2 +
>> 3 files changed, 78 insertions(+), 12 deletions(-)
>>
>> diff --git a/drivers/media/video/omap3isp/ispcsi2.c
>> b/drivers/media/video/omap3isp/ispcsi2.c
>> index 9313f7c..e2e3d63 100644
>> --- a/drivers/media/video/omap3isp/ispcsi2.c
>> +++ b/drivers/media/video/omap3isp/ispcsi2.c
>> @@ -1068,7 +1068,13 @@ static int csi2_set_stream(struct v4l2_subdev *sd,
>> int enable)
>> struct isp_video *video_out = &csi2->video_out;
>>
>> switch (enable) {
>> - case ISP_PIPELINE_STREAM_CONTINUOUS:
>> + case ISP_PIPELINE_STREAM_CONTINUOUS: {
>> + int ret;
>> +
>> + ret = omap3isp_csiphy_config(isp, sd);
>> + if (ret < 0)
>> + return ret;
>> +
>> if (omap3isp_csiphy_acquire(csi2->phy) < 0)
>> return -ENODEV;
>> csi2->use_fs_irq = pipe->do_propagation;
>> @@ -1092,7 +1098,7 @@ static int csi2_set_stream(struct v4l2_subdev *sd, int
>> enable)
>> csi2_if_enable(isp, csi2, 1);
>> isp_video_dmaqueue_flags_clr(video_out);
>> break;
>> -
>> + }
>> case ISP_PIPELINE_STREAM_STOPPED:
>> if (csi2->state == ISP_PIPELINE_STREAM_STOPPED)
>> return 0;
>> diff --git a/drivers/media/video/omap3isp/ispcsiphy.c
>> b/drivers/media/video/omap3isp/ispcsiphy.c
>> index 5be37ce..5d7a6ab 100644
>> --- a/drivers/media/video/omap3isp/ispcsiphy.c
>> +++ b/drivers/media/video/omap3isp/ispcsiphy.c
>> @@ -28,6 +28,8 @@
>> #include <linux/device.h>
>> #include <linux/regulator/consumer.h>
>>
>> +#include "../../../../arch/arm/mach-omap2/control.h"
>> +
>> #include "isp.h"
>> #include "ispreg.h"
>> #include "ispcsiphy.h"
>> @@ -138,15 +140,73 @@ static void csiphy_dphy_config(struct isp_csiphy *phy)
>> isp_reg_writel(phy->isp, reg, phy->phy_regs, ISPCSIPHY_REG1);
>> }
>>
>> -static int csiphy_config(struct isp_csiphy *phy,
>> - struct isp_csiphy_dphy_cfg *dphy,
>> - struct isp_csiphy_lanes_cfg *lanes)
>> +/*
>> + * TCLK values are OK at their reset values
>> + */
>> +#define TCLK_TERM 0
>> +#define TCLK_MISS 1
>> +#define TCLK_SETTLE 14
>> +
>> +int omap3isp_csiphy_config(struct isp_device *isp,
>> + struct v4l2_subdev *csi2_subdev)
>> {
>> + struct isp_csi2_device *csi2 = v4l2_get_subdevdata(csi2_subdev);
>> + struct isp_pipeline *pipe = to_isp_pipeline(&csi2_subdev->entity);
>> + struct isp_v4l2_subdevs_group *subdevs = pipe->external->host_priv;
>> + struct isp_csiphy_dphy_cfg csi2phy;
>> + int csi2_ddrclk_khz;
>> + struct isp_csiphy_lanes_cfg *lanes;
>> unsigned int used_lanes = 0;
>> unsigned int i;
>>
>> + if (subdevs->interface == ISP_INTERFACE_CCP2B_PHY1
>> + || subdevs->interface == ISP_INTERFACE_CCP2B_PHY2)
>> + lanes = &subdevs->bus.ccp2.lanecfg;
>> + else
>> + lanes = &subdevs->bus.csi2.lanecfg;
>> +
>> + /* FIXME: Do 34xx / 35xx require something here? */
>> + if (cpu_is_omap3630()) {
>> + u32 cam_phy_ctrl = omap_readl(
>> + OMAP343X_CTRL_BASE +
>> OMAP3630_CONTROL_CAMERA_PHY_CTRL);
>
> How about:
> u32 cam_phy_ctrl =
> omap_ctrl_readl(OMAP3630_CONTROL_CAMERA_PHY_CTRL);
> ?
Fine for me.
>> +
>> + /*
>> + * SCM.CONTROL_CAMERA_PHY_CTRL
>> + * - bit[4] : CSIPHY1 data sent to CSIB
>> + * - bit [3:2] : CSIPHY1 config: 00 d-phy, 01/10 ccp2
>> + * - bit [1:0] : CSIPHY2 config: 00 d-phy, 01/10 ccp2
>> + */
>> + if (subdevs->interface == ISP_INTERFACE_CCP2B_PHY1)
>> + cam_phy_ctrl |= 1 << 2;
>> + else if (subdevs->interface == ISP_INTERFACE_CSI2C_PHY1)
>> + cam_phy_ctrl &= 1 << 2;
>
> Shouldn't this be:
> cam_phy_ctrl &= ~(1 << 2);
> ?
Probably yes. This has come directly as it was in the original board
code and might not be entirely correct. It works on the N9 at least.
>> +
>> + if (subdevs->interface == ISP_INTERFACE_CCP2B_PHY2)
>> + cam_phy_ctrl |= 1;
>> + else if (subdevs->interface == ISP_INTERFACE_CSI2A_PHY2)
>> + cam_phy_ctrl &= 1;
>
> ... and:
> cam_phy_ctrl &= ~1;
>
>> +
>> + omap_writel(cam_phy_ctrl,
>> + OMAP343X_CTRL_BASE
>> + + OMAP3630_CONTROL_CAMERA_PHY_CTRL);
>
> Again:
> omap_ctrl_writel(cam_phy_ctrl,
> OMAP3630_CONTROL_CAMERA_PHY_CTRL);
Will fix.
>> + }
>> +
>> + csi2_ddrclk_khz = pipe->external_rate / 1000
>> + / (2 * csi2->phy->num_data_lanes)
>> + * pipe->external_bpp;
>
> Can you please explain how did you came up with this formula?
>
> For example, if I keep the pixel_rate, yet I change the number of
> lanes my sensor is using,
> this result is unaltered, as phy->num_data_lanes is always equal to
> the maximum number
> of lanes available in the interface. (for OMAP4, that's 4 datalanes for
> CSI2-A).
The number of lanes is specified in the board code (in the future, DT)
and is thus specific to the board. The clock rate is per-lane whereas
the pipe->external_rate is the total pixel rate on all lanes.
> Meanwhile, in theory, if I keep the same pixels per second, and use
> less datalanes, the
> DDR frequency should at least double.
>
> Now, this brings me to another question, How can the sensor tell how many
> lanes
> is using from the total?
We might consider making the number of lanes used dynamic but that's
currently static. I can't think of any major benefits right now in
making this dynamically configurable.
Does this answer to your questions? :-)
Kind regards,
--
Sakari Ailus
sakari.ai...@iki.fi
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
