"Siju George" writes: > On 3/6/07, Greg Oster <[EMAIL PROTECTED]> wrote: > > "Siju George" writes: > > > > It's working just fine... just probably telling you a bit more than > > you really wanted to know :) > > > > Later... > > > > Greg, > > Seeing that you work on RAIDFRAME let me dare to ask you one more thing :-) > > In my dmesg at one point it says > > ============================================== > Kernelized RAIDframe activated > dkcsum: wd0 matches BIOS drive 0x80 > dkcsum: wd1 matches BIOS drive 0x81 > root on wd0a > ================================================ > > Shouldn't the root be on raid0a ?
I don't know what OpenBSD is in with respect to "root-on-RAID". > Since the dmesg again shows > > =============================================== > raid0 (root) > =============================================== > > and raidctl shows > > ================================================= > Autoconfig: Yes > Root partition: Yes > ================================================ > > for both drives? what does 'mount' say for '/'? RAIDframe used to do a bit of 'hijacking' of the boot disk in order to get itself in as /, but I don't know the details in OpenBSD... [snip] > > Could you please shed any light on why my root device is not "raid0" > but "wda0" still? That part is specific to OpenBSD... > Thankyou so much ( especially for the simple make file introduction on > your website ) > > kind Regards > > Siju > > For my Full dmesg > > ============================================================ > OpenBSD 4.0 (GENERIC.RAID2) #0: Fri Nov 24 20:28:14 IST 2006 > [EMAIL PROTECTED]:/usr/src/sys/arch/amd64/compile/GENERIC. > RAID2 > real mem = 1039593472 (1015228K) > avail mem = 878211072 (857628K) > using 22937 buffers containing 104165376 bytes (101724K) of memory > mainbus0 (root) > bios0 at mainbus0: SMBIOS rev. 2.3 @ 0xfc650 (54 entries) > bios0: Acer Aspire Series > cpu0 at mainbus0: (uniprocessor) > cpu0: AMD Athlon(tm) 64 Processor 3400+, 2193.94 MHz > cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36 > ,CFLUSH,MMX,FXSR,SSE,SSE2,SSE3,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW > cpu0: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 512KB > 64b/line 16-way L2 cache > cpu0: ITLB 32 4KB entries fully associative, 8 4MB entries fully associative > cpu0: DTLB 32 4KB entries fully associative, 8 4MB entries fully associative > pci0 at mainbus0 bus 0: configuration mode 1 > pchb0 at pci0 dev 0 function 0 "ATI RS480 Host" rev 0x10 > ppb0 at pci0 dev 1 function 0 "ATI RS480 PCIE" rev 0x00 > pci1 at ppb0 bus 1 > vga1 at pci1 dev 5 function 0 "ATI Radeon XPRESS 200" rev 0x00 > wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) > wsdisplay0: screen 1-5 added (80x25, vt100 emulation) > pciide0 at pci0 dev 17 function 0 "ATI IXP400 SATA" rev 0x80: DMA > pciide0: using irq 11 for native-PCI interrupt > pciide0: port 0: device present, speed: 1.5Gb/s > wd0 at pciide0 channel 0 drive 0: <ST3120827AS> > wd0: 16-sector PIO, LBA48, 114473MB, 234441648 sectors > wd0(pciide0:0:0): using BIOS timings, Ultra-DMA mode 6 > pciide0: port 1: device present, speed: 1.5Gb/s > wd1 at pciide0 channel 1 drive 0: <ST3120827AS> > wd1: 16-sector PIO, LBA48, 114473MB, 234441648 sectors > wd1(pciide0:1:0): using BIOS timings, Ultra-DMA mode 6 > pciide1 at pci0 dev 18 function 0 "ATI IXP400 SATA" rev 0x80: DMA > pciide1: using irq 5 for native-PCI interrupt > ohci0 at pci0 dev 19 function 0 "ATI IXP400 USB" rev 0x80: irq 4, > version 1.0, legacy support > usb0 at ohci0: USB revision 1.0 > uhub0 at usb0 > uhub0: ATI OHCI root hub, rev 1.00/1.00, addr 1 > uhub0: 4 ports with 4 removable, self powered > ohci1 at pci0 dev 19 function 1 "ATI IXP400 USB" rev 0x80: irq 4, > version 1.0, legacy support > usb1 at ohci1: USB revision 1.0 > uhub1 at usb1 > uhub1: ATI OHCI root hub, rev 1.00/1.00, addr 1 > uhub1: 4 ports with 4 removable, self powered > ehci0 at pci0 dev 19 function 2 "ATI IXP400 USB2" rev 0x80: irq 4 > usb2 at ehci0: USB revision 2.0 > uhub2 at usb2 > uhub2: ATI EHCI root hub, rev 2.00/1.00, addr 1 > uhub2: 8 ports with 8 removable, self powered > piixpm0 at pci0 dev 20 function 0 "ATI IXP400 SMBus" rev 0x81: SMI > iic0 at piixpm0 > "unknown" at iic0 addr 0x2f not configured > pciide2 at pci0 dev 20 function 1 "ATI IXP400 IDE" rev 0x80: DMA, > channel 0 configured to compatibility, channel 1 configured to > compatibility > azalia0 at pci0 dev 20 function 2 "ATI IXP450 HD Audio" rev 0x01: irq 5 > azalia0: host: High Definition Audio rev. 1.0 > azalia0: codec: Realtek ALC880 (rev. 8.0), HDA version 1.0 > audio0 at azalia0 > pcib0 at pci0 dev 20 function 3 "ATI IXP400 ISA" rev 0x80 > ppb1 at pci0 dev 20 function 4 "ATI IXP400 PCI" rev 0x80 > pci2 at ppb1 bus 2 > re0 at pci2 dev 3 function 0 "Realtek 8169" rev 0x10: irq 5, address > 00:16:17:20:2a:a6 > rgephy0 at re0 phy 7: RTL8169S/8110S PHY, rev. 2 > pchb1 at pci0 dev 24 function 0 "AMD AMD64 HyperTransport" rev 0x00 > pchb2 at pci0 dev 24 function 1 "AMD AMD64 Address Map" rev 0x00 > pchb3 at pci0 dev 24 function 2 "AMD AMD64 DRAM Cfg" rev 0x00 > pchb4 at pci0 dev 24 function 3 "AMD AMD64 Misc Cfg" rev 0x00 > isa0 at pcib0 > isadma0 at isa0 > com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo > pckbc0 at isa0 port 0x60/5 > pckbd0 at pckbc0 (kbd slot) > pckbc0: using irq 1 for kbd slot > wskbd0 at pckbd0: console keyboard, using wsdisplay0 > pmsi0 at pckbc0 (aux slot) > pckbc0: using irq 12 for aux slot > wsmouse0 at pmsi0 mux 0 > pcppi0 at isa0 port 0x61 > midi0 at pcppi0: <PC speaker> > spkr0 at pcppi0 > lpt0 at isa0 port 0x378/4 irq 7 > fdc0 at isa0 port 0x3f0/6 irq 6 drq 2 > Kernelized RAIDframe activated > dkcsum: wd0 matches BIOS drive 0x80 > dkcsum: wd1 matches BIOS drive 0x81 > root on wd0a > rootdev=0x0 rrootdev=0x300 rawdev=0x302 > raid0: Component /dev/wd0d being configured at row: 0 col: 0 > Row: 0 Column: 0 Num Rows: 1 Num Columns: 2 > Version: 2 Serial Number: 200612010 Mod Counter: 832raid0: > Component /dev/wd1d being configured at row: 0 col: 1 > Row: 0 Column: 1 Num Rows: 1 Num Columns: 2 > Version: 2 Serial Number: 200612010 Mod Counter: 832 > Clean: Yes Status: 0 > raid0 (root) > ========================================================================= > # raidctl -sv raid0 > raid0 Components: > /dev/wd0d: optimal > /dev/wd1d: optimal > No spares. > Component label for /dev/wd0d: > Row: 0, Column: 0, Num Rows: 1, Num Columns: 2 > Version: 2, Serial Number: 200612010, Mod Counter: 837 > Clean: No, Status: 0 > sectPerSU: 128, SUsPerPU: 1, SUsPerRU: 1 > Queue size: 100, blocksize: 512, numBlocks: 231085824 > RAID Level: 1 > Autoconfig: Yes > Root partition: Yes > Last configured as: raid0 > Component label for /dev/wd1d: > Row: 0, Column: 1, Num Rows: 1, Num Columns: 2 > Version: 2, Serial Number: 200612010, Mod Counter: 837 > Clean: No, Status: 0 > sectPerSU: 128, SUsPerPU: 1, SUsPerRU: 1 > Queue size: 100, blocksize: 512, numBlocks: 231085824 > RAID Level: 1 > Autoconfig: Yes > Root partition: Yes > Last configured as: raid0 > Parity status: clean > Reconstruction is 100% complete. > Parity Re-write is 100% complete. > Copyback is 100% complete. > ======================================================================= > Clean: Yes Status: 0 Later... Greg Oster
